How to install a gear reduction on a 2014+ Honda rancher, foreman, or rubicon

Рет қаралды 44,266

3 жыл бұрын

let us know if this video was helpful for you!
If you have any questions feel free to leave a comment or shoot us a DM on Instagram.
@vesselpowersports on all social medias!
checkout some hondaboats merch at vesselpowersports.com

Пікірлер: 64

@j-muddy93 3 жыл бұрын

Awesome video!

@vesselpowersports 3 жыл бұрын

Thanks!

@juancamacho9136 2 жыл бұрын

Gracias. Men saludos desde México

@williambrooks163 2 жыл бұрын

How did you know when to stop tightening the clutch basket. The one with the one way in it that’s why I haft to change out on mine

@MrMitchhaze 2 жыл бұрын

what happens if you overtighten centrifugal clutch. I just watched this video after I did mine to verify everything the only thing I did differently was just tighten the centrifugal clutch and didn't check for playm reguard less where the gears mesh together I had the slightest bit of movement so I'm thinking it may wear some stuff down but be ok as I drove it amd everything seems fine.

@colemanharvey7193 2 жыл бұрын

Great video

@vesselpowersports 2 жыл бұрын

Thanks!

@rideredoffroad3771 3 жыл бұрын

How long did you take to put it back on and completely finish

@jacobpos5722 2 жыл бұрын

Do you gotta pull the motor when doing clutches? 10 rancher 420? And does a clutch kit really do anything?

@stephaniealtman4021 3 жыл бұрын

left hand thread are right hand thread on the 27 mm staked nuts

@vesselpowersports 3 жыл бұрын

not sure which is which lol normal thread, righty tighty lefty loosey haha!

@kamironpellegrin3145 3 жыл бұрын

What are you sealing the front case with? Also what are the torque specs for the nuts holding the clutches on. Looking to do a GR soon.

@vesselpowersports 3 жыл бұрын

Hondabond or grey rtv. And the clutch basket i just go until tight, ans the centrifugal clutch you tighten it up where there is just a little back and forth movement as you see in the video. Thats how i do it, im not sure on torque specs

@RobertWilliams-up9hf 3 жыл бұрын

I’ll be at Boggs Halloween weekend,would like to ride with you some

@vesselpowersports 3 жыл бұрын

Sounds good, get up with us out there!

@hammahdepartment5667 3 жыл бұрын

Wish you were in Hawaii I’m looking for someone to do my 2016 rancher sra

@vesselpowersports 3 жыл бұрын

Fly me out! ill do it free of charge lol

@jacobreqps4760 2 жыл бұрын

You said lift up on the shifter what if it's a automatic

@mattpierre9993 3 жыл бұрын

Serious question, what way does the neutral switch face in the case, does the long or short side face neutral? Ple help

@vesselpowersports 3 жыл бұрын

long side faces neutral!

@amoryalexander7801 3 жыл бұрын

Where can i find a 35% reduction for my 14 rancher footshift 4x4?? I cant find any. Only ones i find is 07-13

@vesselpowersports 3 жыл бұрын

22fabcreations.com

@braydenstarnes6624 2 жыл бұрын

Does this work for a DCT

@djwilliard3891 3 жыл бұрын

With the 53 did you have to use washer behind GR

@vesselpowersports 3 жыл бұрын

no, didn't use any shims for it

@halofan4life1000 3 жыл бұрын

Is this the same install for a 2013 honda rancher 420? Or similar

@vesselpowersports 3 жыл бұрын

yes I'm pretty sure its the exact same

@julianroberts8610 3 жыл бұрын

@Dalton Bailey reduction boss, don oglesby

@Sidewayzrik 3 жыл бұрын

Isn’t that timing chain pretty stretched out?I can’t really tell

@vesselpowersports 3 жыл бұрын

Nope, its a new wiseco chain

@aurtisanminer2827 10 ай бұрын

No, the guides make it look like it’s sagging but it’s tight.

@lloydeaster4100 10 ай бұрын

Hey buddy I have a 2014 420FA1 , auto -esp .. sra is reduction same has 29.5 sassy.. clutch is slipping now don't know what in it now gr, can I count teeth, cause it may have gr in now, do you know teeth count...35, 53, thanks

@vesselpowersports 9 ай бұрын

Not sure, does your primary gear look welded or have reaction boss on it?

@lloydeaster4100 6 ай бұрын

Hey buddy thanks for responding I've been busy just about to get in it will update you thanks again

@lloydeaster4100 6 ай бұрын

Awesome video to brother 👍

@george2823 3 жыл бұрын

Might be a over asked question but, what tire size is the starting point for needing a gear reduction. I have a 2017 foreman 500 FS

@trentonhuggins8375 3 жыл бұрын

I’m in need of one and I’m on 28 in Moto havocs

@jaredmckenzie7821 3 жыл бұрын

@@trentonhuggins8375 my stock 500 is turning 29.5 outlaw 3s with relative ease but I still want to look into a gr

@rideredoffroad3771 2 жыл бұрын

@@trentonhuggins8375 I pulled 28 havoks before on my 420 and it pulls them just fine without gear reduction

@jonathanprimeaux884 3 жыл бұрын

Um where can someone order that cargo door cup holder at 14 seconds. I've searched everywhere. Nothing. I'm starting to think it was 3D printed

@vesselpowersports 3 жыл бұрын

its an oem honda part, check out tbm_customs on instagram and send them a message.

@jonathanprimeaux884 3 жыл бұрын

@@vesselpowersports lol literally minutes after I posted it this, we found it. It's 44.95ish on hondas website

@Carruthers84 3 жыл бұрын

Same process for one with a dct?

@vesselpowersports 3 жыл бұрын

if I'm not mistaken yes, just looks a little different

@grayhancock6953 3 жыл бұрын

It’s not you have a gear in the back case

@allen8736 3 жыл бұрын

Does that 520 on assanators have a gr

@vesselpowersports 3 жыл бұрын

Yes, 53%

@blakemarkin9783 3 жыл бұрын

@@vesselpowersports Ive got a 520 Rubicon and want to run 29.5" Assanators without a gear reduction... do you think it'll get bogged down or can it spin them pretty good

@stevenlav228 3 жыл бұрын

It will have np if you have a dct transmissin and you put it in low

@IssaBoat. Жыл бұрын

Where can I buy a 35 percent gear reduction?

@vesselpowersports Жыл бұрын

reduction boss

@rylancalcagino1247 29 күн бұрын

This is only up to 2021? I got a 22

@vesselpowersports 29 күн бұрын

works the same, just made the videos when the 21s first came out.

@Hayden_Alexander Жыл бұрын

How much would it cost for you to do mine

@vesselpowersports Жыл бұрын

Unfortunately we aren't doing any installs at the moment

@zeekcombs2644 Жыл бұрын

i need all the tools used in this video if u don't mind don't do great remembering lol.

@vesselpowersports Жыл бұрын

10mm 27mm 6mm 12mm 14mm hammer extension 3 jaw puller or clutch puller tool Should be everything lol

@casongrainger2236 3 жыл бұрын

Where can I get a GR?

@vesselpowersports 3 жыл бұрын

22fabcreations on instagram

@z7xdefectz 3 жыл бұрын

Hey man u selling any hondas

@vesselpowersports 3 жыл бұрын

Yes, soon

@z7xdefectz 3 жыл бұрын

Let me know call me 352 727 3356

@z7xdefectz 3 жыл бұрын

Thanks man

@tracethompson0331 2 жыл бұрын

If only you understood how much money and business you lost making this Video. SHMM 🤦🏻‍♂️