Thanks Again. I watched this video years ago when I had to replace my Moen Faucet Sprayer. I had to replace the Spray again and found your video to be a helpful reminder. Also, as a note to your viewers, Moen's "Buy it for Life" policy is real, I have replaced the Hot & Cold Cartridges once and Sprayers twice for free with free shipping of parts.

I am a 60 year old woman who decided to change her faucet by herself for the first time ever. I watched a couple of other videos that made it look easy. Then I got stuck and found out I needed a basin wrench. My friends husband borrowed one and she brought it over. We started following the instructions in the moen box but were still not really sure so I went on the moen site to see if they had a video and their site was down for maintenance. So looked on KZfaq for a tutorial for my model and there you were. I cannot thank you enough for this video. Your instructions were so clear and precise. We watched each step, paused the video and did it, repeat until done. Voila I have a properly installed new faucet. Thank you again.

When I put in a new faucet the sprayer didn't work. After seeing this video I checked to see if the MOEN name was right side up on the diverter and sure enough, I installed it upside down! After flipping it the sprayer worked like it was supposed to and suddenly, life is good again! Thanks for pointing out the "small details" like that!

You were right, it was Easy for you to install on a nice clean worksite! Unfortunatly mine was a Mess! The Old MOEN was installed by the Stooges. The Shut Off Valves were so "Old & Cheap" they had Plastic Handles and one Snapped off in my hand before it shut off the Flow. The other was laid right up against the Sink and I was able to get it mostly shut off with 10/12 Thumps with Plyers. I just shut off the Main after that. At least they used 12" feed lines that were so short they were bent at 85* to 89* at the Connection. I went back with 20", just to hopefully give me a chance at sucess. I know you can't forsee things like this, but it's NOT Always that Easy.

Thanks for the video! It's the first time I've installed a faucet on my own and went easier than I thought!

I just installed this setup this morning....it was SOOO easy. The hardest part was taking out the 10 year old faucet. =)

Simple, short, and informative, you couldn't have made this video any better. Thank You!

Almost perfect. The only thing you left out was the necessity and use of a basin wrench. Thank you for helping me with my kitchen!

It's recommended by Moen to remove the aerator after installation to flush an debris out. Run water for 15 seconds, both hot and cold and then replace aerator.

Thank you for this video. I actually needed it to disassemble my Moen faucet hookups to install a glass rinser, so thanks again!!

I know this is 5 years ago, but we just got this faucet today and plan to install tomorrow. Personally I have no clue what I'm doing, so this video is the only help I'll have. Thank you!!! Seems easy enough. I will be back tomorrow and either be crying cuz I ruined not only the faucet but the sink or I'll be bragging "I did it" lol thanks again

Thanks for the video it gave me the confidence to try it myself. I just finished installing my first facet. I did use a little plumbing putty around the 3 main holes just to ensure no water drips through.

Great video. Installation went smooth. Thank you!

Thank you Sir !

Just what I needed. My first time and your video made life a bit easier. Thank You!

...I don't even want to be dealing with this, right now ... thanks for the tutorial.

I'll be doing this sometime this week. Thank you for the demo.

Great video!

I am going to attempt to do this next week. Thanks for the video. Makes the installment look easy. Wish me luck.

Wow great installation video, super production value. Thank you for posting! 😇

Just installed one of these & your video helped a bunch. Thanks.

Good, clear instructions! 👍

I had leaks .... I bought the cheapest hoses for my Delta and tightened as tight as possible. I think that the gasket inside the hoses got torn because i tightened it so tight.. Now I see why this "click" tighten idea was invented.

Thanks for the video!

Thank you so VERY much!!!

Something people do not know about or know where to find,are the Plumbing Supply Houses that the pros go to. Many times what you need, will not be at Home Depot or Lowes, but always at the local plumbing supply. I mention this because, there are actually cheaper than the Big Box Stores & sell to the public at the same price as the tradesmen & can answer your questions.

I remember in the past 10 years ago when you used to have to have plumbers putty, thread tape and a special wrench to get up behind the sink for the waterlines.

Thanks! I’m about to install that exact faucet. I noticed you didn’t do anything with the little packet of grease?? Guess I’ll throw it int my toolbox? I LOVE the new hoses! Unfortunately, I don’t have any extra $$$ to go and get them, maybe Santa will bring me some. Old school, “need a wrench” hoses for me. Lol. Looks great by the way… both the faucet and the video. Thank you so much, it’s been a few years since I had to replace one so it’s nice to have a quick refresher before I climb underneath my sink😱.

Thanks a lot for the very informative and useful video..

Thank you for sharing his video!!

Thanks for the help.

Thanks for sharing this

Very helpful!!

Thanks

Thanks for sharing 👍🏽

Thanks buddy, helpful video!!!!

Video well explained. you did a great job!!!

Aren't you supposed to use Teflon Tape or something on all the threads?

Thank you for this,

I did it! Thanks for your help (:

thank you for this, it was very helpful

Great Job!

Thanks for your Help I’ll do mine next week

How did you bypass the airgap?

Can it be installed & used without the side sprayer?

Make a video removing the old faucet. I got everything loose except where the sprayer has that permanent valve under the faucet

Thanks Sir you rock!

Gramma going to try this myself to save some $ Wish me luck.

Ty

Thank You!!!!

Can u tell me why I have 2 Quick connects with my new Maureen sprayer and hold you with no week before but now the new one is leaking

How do you get the sprayer to stay pointed straight? I'm ocd. 😆

Where did you get the water supply lines with the plastic end attachments? Those look like they'd really make it easy.

Oh I wish you lived in my area....in have a plumbing issue and the plumbers in my area are a joke!😏

I have bought the same faucet, it is very very lightweight, you don't feel you have the faucet on your hand. It should have been a thicker gauge at least on the seating part. You have to provide a kind of washer, one for the hot side and for the cold side, keep the faucet in the center, and not moving. That is the hole is wider than the threaded brass tube goes underneath. PVC washers come with it is not wide enough rim to cover the hole, you can see the light through part of the hole not fully covered by PVC threaded washer goes underneath. The circumference on the top should be wider at least 1/4 more around with the existing surface. Faucet move and don't stay even in the center on the raised part. I made a wider copper washer snugly fit the hole and wider than the PVC threaded washer, Now it didn't move, and don't see light through also. Don't be cheap to provide a wider washer. Always something missing, Thanks Paramasivam

Does the whole Facet wiggle around after you tighten it? I bought one off of Amazon that came with seals and I tightened it as best as I could but it wiggled around alot

For a sprayer replacement only: Can I replaced just the sprayer or do I need to replace both the sprayer and the connecting hose on a Quick Connect Moen side sprayer?

I just want to replace the sprayer so is it the same model?

Mine went right in , everything was fine except it leaked inside the faucets, I thought the fittings would leak, it was the cheesy plastic faucet instead.

What supply lines were you using at 2:55

what if the water is too hot?

Just installed it, went very easy however my hot water is now not running...I have zero clue how when it was literally just running 5min ago and all I did was shut the valve off, replaced the faucet, turn the valve back on, now no hot water....I'm stumped

Great video! If I could ask, if you dont want to use the spray nozzel, do you have to put a screw cap on underneath of the faucet where the water would come out. Thanks

Don't you need to apply the Teflon tape to the threads? Thanks

You only connected one inlet? What about hot cold?

... I can't get the hoses disconnected!!! The jokers that put the sink in have the washers on so tight they won't budge!!! - which means I can't pull out the faucet in order to replace the copper plug inside. VERY frustrated, the kitchen is a mess and I'm starting to feel like Kramer, washing out my dishes in the bathroom or basement sink. ANY advice???

Do you need to use plumber's putty when doing this installation?

I was doing great but couldn't figure out why I couldn't tighten the nut under the sprayer. I have the line hooked up already and can not get it off. Any suggestions? UGH!!!

I have a feeling finding those slick water supply lines will be difficult.

Did those "toolless" water lines come with the kit? I'm over basin wrenches and "breaking" things lol

My sprayer stopped working. The spray was SO strong, I wanted to lower it. I pressed the button on the tube under the sink. Now the sprayer doesn't work. HELP!!

You forgot to show how to install the sprayer base on to the sink with only one person. I'm installing this now and no way to tighten this without two people. Thinking of using a vice grip to stop the fixture from rotating. Care to share how you managed? P.S. Seems if you screw the fixture in as much as you can then insert the sprayer hose, pulling on the hose supplies sufficient friction to complete the screw down. Another downer about this Moen, Try using a hair dryer on the spray hose to relax it. This thing is coiled like a Rattlesnake. I can only extract about a foot through the top of the sink -no more. The only saving grace is the spray head rotates 360 degrees, otherwise it would probably be useless. Finally, the handles are too long (in the name of style no doubt) and bump into the sprayer head (which can be rotated out-of-the-way but still a pain). Who is designing these things? Obviously, the lowest bidder.

What if the water is way too hot?

Where did you get the water lines that you can tighten by hand?

Can you give me a part number for the supply lines?

No need for Teflon tape using Fluidmaster Click Seal?

The part that connects the hose to the faucet leaks (see kzfaq.info/get/bejne/gZyEjKV8v7uzZac.html). It clicks nicely to the faucet, snug as it can be. The hose clicks in place too. So what is the issue?

I am have difficulty with the side sprayer. The minimal instructions in this video are not helpful

Too long

Thanks