How to install a REDARC Tow-Pro Elite V3

How to install a REDARC Tow-Pro Elite V3 - Isuzu MU-X / D-Max

Рет қаралды 36,499

Күн бұрын

In this video we show you how we went about installing the REDARC Tow-Pro Elite V3 Brake Controller (EBRH-ACCV3-12) in a MY19 Isuzu MU-X using the REDARC Universal Wiring Harness Kit (TPWKIT-013) and Switch Insert (TPSI-006). The same principles apply to the Isuzu D-Max.
0:00 - Introduction
0:26 - Tow-Pro Elite V3 Important Info
2:04 - Wiring Harness Kit Important Info
5:05 - Installation of Tow-Pro Elite and Switch
9:15 - Installation of Harness
18:11 - Testing
18:50 - Conclusion
Thank you for watching! Please subscribe: / @njsinstructional

Пікірлер: 22

@trevorpollock3024 2 ай бұрын

This was an exceptional video on Redarc brake controller! 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

@NJSInstructional 2 ай бұрын

Glad it was helpful!

@Mrboxo 2 жыл бұрын

Great install guide. Don't forget to install the locking clip on that 4 pin molex plug.

@NJSInstructional 2 жыл бұрын

Thanks for the tip!

@jasonknox1926 4 ай бұрын

That was actually a very clear and comprehensive vid! Will be very helpful for me when installing on my Dmax, just would have recommended some conduit / tubing to protect the wire underneath the car - but probably not essential

@NJSInstructional 4 ай бұрын

Glad it helped!

@graham6401 Жыл бұрын

Clear, logical instructions which could be used for many vehicles.

@NJSInstructional Жыл бұрын

Cheers, thank you!

@Looseyboi Жыл бұрын

Mate your a top notch guy. Everything was explained clearly and matched what was shown. Have a great day 👍🏼

@NJSInstructional Жыл бұрын

Glad it helped!

@boreeng Жыл бұрын

One end of the orange wire joins to the supplied connector at the rear of the vehicle. But where does the other end connect to?

@muralidharamysore2549 Жыл бұрын

One of the best installation videos. Many thanks for sharing.

@NJSInstructional Жыл бұрын

Glad it was helpful!

@brycesteep3144 4 ай бұрын

Great instructional, very helpful for installing the exact same system in my own Mu-x. I noticed you have the reed switch in the trailer plug wired so that the reversing proximity warning sensors are disabled when reversing while towing. I have the same flat trailer socket but having some trouble working out how to connect the reed switch to the car wiring system, I couldn't find any hints or ideas online - can you offer any help with this?

@maskofsorrow 11 ай бұрын

Does it affect your car warranty or insurance if you DIY??? You explained the procedure well and anyone could follow it but there's that element of uncertainty about insurance forfeiture risk with DIY. Would like to do it myself.

@jamesgibbins4054 6 ай бұрын

How did you perforate the grommet in the firewall?

@NJSInstructional 6 ай бұрын

Possibly with a metal coat hanger...

@jamesgibbins4054 6 ай бұрын

Legend thanks!

@dollarking9641 Жыл бұрын

Wer did the orange cable come from ?

@NJSInstructional Жыл бұрын

Check the video at 2:09 and onwards. The orange cable is part of the REDARC Harness Kit.

@markschultz1606 Жыл бұрын

AT A GUESS, the orange is there to make it easier for installers; as the 7-pin connector doesn't have room for multiple cables into a single terminal, which also makes it easier for DIYers. Instructurally, you'd need to jumper the brake light to the brake input: again, AT A GUESS.

@Billybob11345 9 ай бұрын

@@NJSInstructional its there for the diode thats back up in the harness to stop 12v back feeding