How to Install a Shower in Your Boat | Sailboat Restoration | Trawler Boat Building (Ep66)
Рет қаралды 1,309
6 ай бұрынHave tou wvet wanted to install a bigger shower in your trawler or sailboat restoration project RV remodel? This episode I install the plumbing oarts and RV plastic shower pan for the shower in my Albin 27 pocket trawler restoration.
Welcome to my boat building channel! This is my trawler restoration of an Albin 27 pocket trawler. Every couple of weeks I post a boat building or boat repair video to document various boat projects, sailboat restorations, or boat repairs. And when all else fails, I tell stories of boat motivation.
**MotorCity Boat Werks has no sponsors and receives no compensation from any of the brands featured or recommended.
However, there may be compensation from the use of Amazon affiliate links below.**
Equipment featured this episode:
Ambassador 1.5 to 1.25" reducer drain
amzn.to/42rlFWJ
1 7/8 Hole saw for shower drain
amzn.to/3HLkFmS
3" hole saw - "Corn-holio"
amzn.to/42yH28v
Be sure to like and subscribe.
/ motorcityboatwerks
Questions or comments can can be submitted via the comments section or at:
📧motorcityboatwerks.weebly.com/...
Donations:
www.paypal.com/donate/?hosted...
Join The Werkers (fan club):
/ motorcityboatwerks
#boatprojects #boatrefit #boatrestoration #boatbuilding #trawlervlog #trawler #boatlife #sailboatrestoration #sailboatrefit #boatworkstoday #waverover #motorcityboatwerks
My videos are similar to sailboat restoration videos like Boat Works Today; My videos are similar to boat project videos like Boat Works Today; Project Brupeg; Sampson Boat Co; The Duracell Project; Project Duracell; Tula's Endless Summer; Sailing Delos; Sail Life; Travels with Geordie; SV Seeker; Danger Marine; My First Boat; Sailing Dawn Hunters; Seeking Seas; Sailing Flying Coney; AYO Fishing; Peter Slack; Sail Life; Wilding Sailing; Life on the Hulls; Sailing Wave Rover; SV Tapatya; LOJO Fishing; Sailing Wave Rover; Angry Mack; Sailing Lahakai
BoatWerks Theme: "Early Retirement Start" by Ryan Muns Eyes on the Moon Studios
@jefersonscholze9445 5 ай бұрын
What I like? The true life! You share all, successes and mistakes. It shows how a simple drain installation can bring complications and difficulties. The good news is: You always find a good solutions. Thanks to share.
@motorcityboatwerks 5 ай бұрын
Great to hear from you Jefferson! Thanks so much😁 I’m glad you enjoy the videos 👍😁
@danielmerson68 5 ай бұрын
I agree, your channel has more practical solutions and thoughts than most. I really enjoy watching you work through a problem.
@motorcityboatwerks 5 ай бұрын
Welcome Aboard Daniel😁 I’m so happy you get something out of the videos. It’s great to know that people appreciate the way I try do things differently in the Boat Werks 👍😁 thanks again
@charles.neuman18 5 ай бұрын
OK, we're making progress. Finally, some hardware - not just sanding! I'm looking forward to seeing where you get access to the plumbing below.
@motorcityboatwerks 5 ай бұрын
I feel the same way Charles !😁👍
@russellmurphy8111 5 ай бұрын
Nice work and great explanation!
@motorcityboatwerks 5 ай бұрын
Thank you Russell😎👍
@dougstearns6746 5 ай бұрын
Great channel Joe!
@motorcityboatwerks 5 ай бұрын
Thank you Doug!👍😁
@907T 5 ай бұрын
Well done Joe. I'll be interested to see if you get away without a sump.
@motorcityboatwerks 5 ай бұрын
It’s coming up in the next episode Joe 😁
@davetowz 5 ай бұрын
Some hole saw arbors have long enough threads that you can screw inside the hole saw you want with one that fits the hole you have.
@motorcityboatwerks 5 ай бұрын
Brilliant! That’s what I need 😁👍Thanks Dave
@davelawrence6777 5 ай бұрын
The gentleman is right about reversing the drill on the hole cut just enough to score the surface then change the direction of the drill to forward. This same principle applies to standard drill bits most especially on fiberglass it helps prevent chipping the gel coat also when the hole is drilled then use a counter sink just enough to ease the hole edges and it will help prevent checking of the finish when you draw down the fastener.
@motorcityboatwerks 5 ай бұрын
Thanks Dave 👍😁 I’m personally opposed to using a drill bit or a saw blade in the wrong direction.
@jamesdalton122 5 ай бұрын
To enlarge a hole that’s been drilled with a hole saw use the same size hole saw, same as the hole that’s there, and cut a disc from a piece of plywood put the disc in the existing hole and then use it to center the larger hole saw. Once the larger saw starts cutting it will be even all the way around the smaller hole. I use it all the time when installing new larger diameter gauges into existing console holes
@motorcityboatwerks 5 ай бұрын
Thanks James 👍😁 this is an interesting idea. But from experience not as successful as you would think. And not applicable in many situations.
@charlescoates6661 5 ай бұрын
Just for future reference, if you put the drill in reverse it is a lot less likely to tear the plastic. The same way carpenters turn their saw blades backwards when cutting plastic.
@motorcityboatwerks 5 ай бұрын
🐙 ok 👌 Do you know where they sell the backwards saw blades at the hardware store?
@luckytoastsebastian 5 ай бұрын
I've remodeled a few bathrooms in houses. The caulk is the weak point. I'd try to recreate what you cut off like a z flashing so water has no path down between that edge. Unless you're using an epoxy. Great work!
@motorcityboatwerks 5 ай бұрын
Thanks Sebastian! Be sure to subscribe 😁
@charles.neuman18 5 ай бұрын
When we had our bathroom redone, the new tub was a little short (or the space was a little big), so they cut off the lip on one end of the tub. They butted the tiles on the wall to the edge of the tub, but there was no lip behind the tiles. Bad idea. Water got through that crack and damaged the ceiling below. I discovered what they had done after investigating the water source. I put generous caulk in there, and that stopped the leaking. I've kept up with caulking since then, and it's held up OK. But I can't take my eye off the caulking.
@motorcityboatwerks 5 ай бұрын
Luckily the entire head area is made of coosa board and fiberglass so I think we’ll be ok
@davidbauerdorf1324 5 ай бұрын
That was my only worry. As a home improvement contractor. But like Joe said since there is nothing to rot ……. And I’m with the epoxy instead of caulk
@motorcityboatwerks 5 ай бұрын
The problem with epoxying the pan in place is that then it cant be removed if there’s ever an issue. So the solution will be mounting with PL Marine and then PVc trim pieces mounted same to finish off.
@vincentdsnt 5 ай бұрын
Measure twice caulk once........🙃
@motorcityboatwerks 5 ай бұрын
Exactly 😁
@ashley-tm1uk 5 ай бұрын
oooo…not sure how your caulk joint is going to adequately keep water out , even though it’s raised from the floor, without that lip, and tucked behind the shower wall…i think i’ve just been snake bit when it comes to water proofing shower stalls…perhaps a bit hyper vigilant ? …hope she works for you!…
@motorcityboatwerks 5 ай бұрын
😏
MotorCity Boat Werks
Рет қаралды 2,3 М.
MotorCity Boat Werks
Рет қаралды 2,1 М.
Sailing Rum Runner II
Рет қаралды 24 М.
QM Drain
Рет қаралды 154 М.
MotorCity Boat Werks
Рет қаралды 3,1 М.