How to - Install a Trigger Position Sensor on a Classic Mini

Рет қаралды 3,929

Жыл бұрын

#classicmini #fuelinjection #retroefi
Join this channel to get access to perks:
Patreon - / classicminidiy
KZfaq - / @classicminidiy
❱ Shop - store.classicminidiy.com
❱ Seven Mini Parts - bit.ly/7evenmini
❱ Instagram - / classicminidiy59
❱ Facebook - / classicminidiy
❱❱ Address for Mail Time:
6241 South Blvd
Box 241403
Charlotte, NC 28217-4157
❱ Parts in this Episode:
Trigger Position Sensor Kit - store.classicminidiy.com/coll...
Thanks for watching Classic Mini DIY! Please note Classic Mini DIY assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Classic Mini DIY recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Classic Mini DIY, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Classic Mini DIY. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.

Пікірлер: 20

@rennkafer13 Жыл бұрын

Another great kit Cole... adding one to my list of "things to buy".

@Macaco_Branco Жыл бұрын

Nice to see you back, Cole! Thanks for sharing, the system looks interesting 😊

@classicminidiy Жыл бұрын

Thank you! I’m not totally back yet because I’m actually just on my way to Italy for international mini meet tomorrow. But I had some free time and figured I was motivated to make a video today.😎

@Macaco_Branco Жыл бұрын

@@classicminidiy Nice, that's how it should be! I wish you a lot of fun and great impressions at the meeting in Italy. ^^

@philtucker1224 Жыл бұрын

Great video Cole and a really important addition if emission controls are required..

@JPMergens Жыл бұрын

Nice kit! If I ever need and ECU this will definitely be a nice addition.

@owlytv 9 ай бұрын

Hi I was wondering if you'd do a version of the trigger wheel key mounting and wheel kit for a Datsun a series double crank pulley if I posted one over for reference? I'm doing a turbo efi conversion in a Morris Minor

@metalwright Жыл бұрын

Check your ECU manual. I think Megasquirt 3 wants a certain amount of lead time before TDC, something like 70-80 degrees..

@classicminidiy Жыл бұрын

Definitely wise words to check on your individual ECU however, most of them can have a positive or a negative offset configured in their settings. I know DTA fast and Haltech, as well as ECU master all can do that pretty easily. I am not sure if mega squirt or mega jolt can do a negative offset though.

@ToddDunning Жыл бұрын

Exactly, I'm doing 90. And yeah MS can do negative offset.

@sw5carbon Ай бұрын

do you do a kit for the triumph tr7 2ll how mush will it cost

@Sternhammer89 Жыл бұрын

Nice looking kit. Interesting location for the sensor bracket, could do with moving mine to that location as it's currently in the way of the Timing Teeth on the Timing Chain Cover.

@classicminidiy Жыл бұрын

We had to think really hard about how we would make it compatible with any mini regardless of the timing cover and this was the best way we could come up with. Out of the way but super secure.

@SpeedyDad1 Жыл бұрын

Will the kit fit with the Vmaxscart SC pulley?

@classicminidiy Жыл бұрын

We haven’t tested it with that set up yet. I have a hunch that it will not fit because of the dual belt pulley set up. That said there is a little bit of room between the radiator bracket and the pulley so it might work.

@GoProHorseGuy 5 ай бұрын

Cole is Pin 1 Positive (5V), pin 2 signal, and pin 3 negative? Thanks

@classicminidiy 5 ай бұрын

Hey! Apologies this should be on my downloads page. Here is a link to the image for reference classicminidiy.s3.amazonaws.com/Downloads/HallSensor.jpg

@GoProHorseGuy 5 ай бұрын

@@classicminidiy Thanks Cole, greatly appreciated, can't wait to install your crank and sensor to my Mini.