How To Install An OVE Barn Door

How To Install An OVE Barn Door - Step By Step

Рет қаралды 21,202

Жыл бұрын

In this video I'll go through step by step how to install an OVE barn door from start to finish. I'll show you how to prepare for the installation and also explain what you need to do to make sure the installation goes smoothly. I'll explain each step and show you exactly how to execute the install and what to watch for and avoid.
#barndoor
#howto
#stepbystep
#installation
#tutorial

Пікірлер: 29

@glenmccall3921 6 ай бұрын

Just finished installing our door and I cant begin to tell you how helpful your video was!! The instructions that came with this kit were terrible and I'd have given up if I didn't use this video instead. The only mistake we made was going with the 86 1/4" measurement from the floor to the top of the rail - which happened to line up exactly with the center line of the backer board - and we should have gone with the 86 1/2" measurement instead. When we went to hang the door, rested on the rail, but also perfectly on the floor, so it couldn't slide. So unfortunately, I had to remove the rail bolts and reposition them 1/4" higher to allow for the clearance and the guide on the floor. I wish you were able to go into more detail on the "slow close" assembly, as for us, this was the hardest step of the entire install. We followed your steps, and with a quick glance at a couple other videos that zoomed in on the door brackets and assembly - we were able to successfully install them on the first try. Your tip to remove the door from the track to mount the door brackets was super helpful and worked like a charm! Thanks again.👍👍

@A.G.T.A 6 ай бұрын

So glad the video helped! Ya, there are a few smaller details that in hindsight I would have delved into further. Excellent job installing this yourself! Even with video instructions this door is not an easy install, you must be handy to start with. Thank you for your feedback on the video ❤️

@dpodsful Жыл бұрын

Looks really good!

@A.G.T.A Жыл бұрын

Thank you very much! 👍

@jules-yi8rn 6 ай бұрын

Nice.... thanks for breaking it down. I'm going to be installing one of these for myself soon, and I wanted to see what I was getting into😂. Doesn't look too hard, though... great video!

@A.G.T.A 6 ай бұрын

You’re welcome! It’s really not that bad to install, pretty intuitive… best of luck! 😊

@drewinstallshardware 11 ай бұрын

Great video! Very helpful 😊

@A.G.T.A 11 ай бұрын

Thanks! Hope it helps people with a couple of the irritating things you’d find out the hard way when installing these doors

@rasgum7 10 ай бұрын

Very nice and informative. Thank you,

@A.G.T.A 10 ай бұрын

You’re very welcome! Best of luck on the install 👍

@user-rv5fp5vu6e 7 ай бұрын

Thank you very helpful

@A.G.T.A 7 ай бұрын

Very welcome! Glad I could help 👍

@garyclemson3032 Жыл бұрын

How far from the left of your framed opening do you place the left end of the hanger rod ? Thanks.

@A.G.T.A Жыл бұрын

Basically you split the difference… so take your door frame size (with trim or without) take the door size out of that and divide by 2 (ex: 38” opening to end of trim - door width (36”) = 1” reveal on both sides - make a mark and go 6” from that point to the left side (in this example it would be 5” from the outside of the trim). Hope this helps… if not, let me know, I’ll try to explain myself better

@TroyNeilProductions 4 ай бұрын

When you install the lag bolts for the track, do they go through the header board and into the wall at all?

@A.G.T.A 4 ай бұрын

They will go through and into the wall. If you have full backer behind the drywall, they should go through and catch that. If your header board is attached properly to studs in the wall, this is a redundancy that’s not needed, but extra reinforcement doesn’t hurt

@TroyNeilProductions 4 ай бұрын

Thanks very much for the reply and the video. I'm installing on lathe and plaster and just getting a sense of things. I guess this means you need to drill pilot holes through the header into the wall before the lag bolts? Our header will already be bolted into the studs, so this is just for the track.

@miltongranda453 2 ай бұрын

Nice job , i do that too

@A.G.T.A 2 ай бұрын

Thank you 🙏 enjoy the new door!

@moxu9265 11 ай бұрын

❤

@A.G.T.A 11 ай бұрын

❤️🙏

@drazenradojcic8676 4 ай бұрын

Hi, nice job! After installation I have a gap 3cm between door and wall. Can you recommend how to solve it?

@A.G.T.A 4 ай бұрын

Does your opening have trim? The gap is made so the door doesn’t hit the trim as it passes, so the only way to fix any kind of excessive gap is to do something about the top track… you could possibly remove the back plate of the track and replace with a thinner plate… anything that would shorten the distance between the top track and the wall… just beware that you are ensuring stability in the track and clearance of the door with the slide

@machmslf 7 ай бұрын

Do you happen to know overall height to the top of the rollers? Im framing a basement right now and the wife wants this door to one room and im hoping i have the height

@A.G.T.A 7 ай бұрын

I’m pretty sure it’s about 88”…that’s based on 84” door… might be tight for a typical basement

@machmslf 7 ай бұрын

@@A.G.T.A thank you for the reply! Its a newer house but the way the duct work is ran it just may work

@A.G.T.A 7 ай бұрын

@machmslf well then you may be in luck since newer homes typically have taller basements, so a regular sized barn door has a good chance of fitting… best of luck with the installation and overall finish of your basement!