How to Install and Replace a Symmons Temptrol Spindle TA-10

No video

How to Install and Replace a Symmons Temptrol Spindle TA-10

Рет қаралды 15,611

Жыл бұрын

#Temptrol #Symmons #shower #faucet #spindle #adjust #hot #water #temperature #diy
Symmons Temptrol Replacement Parts
------------------------------------------------------------------------------------------------------------------
Buy the Symmons TA-10 Temptrol Flow Control Spindle Assembly on Amazon here: amzn.to/3Zawev9
As an Amazon Associate I earn from qualifying purchases and you help support the channel (paid ad)
Symmons Temptrol Repair videos:
------------------------------------------------------------------------------------------------------------------
See How to Replace the Hot and Cold Seats in a Symmons Temptrol Valve here: • How To Replace the Hot...
See How To Adjust Temptrol Shower Faucet Hot Water Temperature Limit Stop here: • How To Adjust Temptrol...
See How To Replace the Temptrol Shower Faucet Diverter Handle here: • How To Replace Diverte...
Buy the GoPro Hero 8 Black camera that we used to film this video in 4K 60fps here: amzn.to/2C4FMCm
As an Amazon Associate I earn from qualifying purchases
Experiencing problems with the water not being hot enough in my Symmons Temptrol Shower Valve I replaced the TA-10 Spindle which is in charge of the mix of hot and cold water when you turn the handle. It is a relatively easy job and recommended as part of the troubleshooting steps in the Symmons Temptrol Shower Valve manual. If this doesn't work, you probably have to replace the hot and cold seats but if your spindle is jammed and not working properly this might be all you need.

Пікірлер: 20

@Sa-gu5oh Жыл бұрын

Thanks for the video, I was able to replace mine myself. Great video!

@EricDIY Жыл бұрын

You're welcome...like and subscribe

@carolinecrockett4210 Жыл бұрын

I've had the part for a week and finally ready to do it. Note to anyone who is doing this symmons will send you the part (and pretty much any other) totally free. 5 min phone call on a Monday night and it was delivered Friday. I'm in MA where they are based so it might take a few days more if you live in another state. They don't ask for proof of purchase like some others when calling for warranty parts.

@Sa-gu5oh Жыл бұрын

Thanks for this, saved me 50 bucks!

@michaelfreel6893 10 ай бұрын

That was a big help. Thanks.

@EricDIY 10 ай бұрын

You're welcome...like and subscribe

@KursRage 8 ай бұрын

Thank you Sir!

@EricDIY 8 ай бұрын

You're welcome...like and subscribe

@deborahpeterson772 Жыл бұрын

I've got the parts and have been working up the courage to replace the spindle. Your video is BY FAR the clearest and most informative I've watched! I have a couple of questions. My unit is a tub/shower unit--are there any other steps for this type of unit? I've watched your hot/cold seat replacement video because I think I'll have to replace those, too. My second question: my unit has not been taken apart for at least 30 years so I'm anticipating stuck parts. I have the old raven tool and will get the new Symmons tool for the replacement parts, but can I use WD-40 or another lubricant if I have trouble loosening the old parts?

@EricDIY Жыл бұрын

You can use wd40 but will want to let the water run after to get any of it out. The tub/show should be the same as it's the diverter handle and an extra pipe that control the tub. The spindle is easy to replace (not so much the hot and cold seats). Just make sure to turn off the water and put the handle to warm before you take it apart as if you take it off with it all the way off you could damage some parts.

@denisronchini2258 9 ай бұрын

When servicing it (regular cleaning when the veins are clogged with debris), do you remove the cartridge in the open (warm) position or can you simply remove the cartridge with the switch in the close position? Also, I think I didn't set the cartridge all the way up against the cap, before mounting it back into the housing, which made my handle extremely hard. I hope I didn't damage it. I'm gonna have to re open everything today again and double check that. Huh! 😮

@EricDIY 9 ай бұрын

They recommend turning it to a warm setting to not cause any damage to the cartridge when you pull the cartridge out.

@denisronchini2258 9 ай бұрын

@@EricDIY I didn't do that. I also think I "unscrewed" T12 a couple of turns from the spindle/cartridge when I removed T12 from the housing. (Naturally the cartridge was under pressure and was stuck to the inside, allowing the cover to spin around the cartridge. When I re-installed it, I did not set the cover up against the cartridge, and therefore, it is too hard to turn now (the cartridge is too far inside of the housing). (I figured I would just put it back the same way it came out to begin with). Rookies mistake! I'm gonna have to repeat the entire process. Huh! I hope I didn't damage it. PITA

@stephaniewachtel Жыл бұрын

Dying to know...was the shower hot enough with the new spindle? Thank you very much for the tutorial!

@EricDIY Жыл бұрын

Going to probably have to replace the hot and cold seats (everything else in the bathroom is fine for hot water so this should do it). Video to follow once I do it. They do say to replace the spindle first for this problem and to do the hot and cold seats it takes a special tool (which I already own)

@EricDIY Жыл бұрын

Fixed the problem tonight by replacing the hot and cold seats tonight...I will be making a video. Not the easiest but doable

@EricDIY Жыл бұрын

Here's a link to the replacing of the hot and cold seats kzfaq.info/get/bejne/ad6IibN5ktfTf3U.html This video shows what fixed it

@jtinero Жыл бұрын

RP just means retail packaging. Did you have to buy the gasket kit?

@EricDIY Жыл бұрын

@@jtinero I did not..unless you're referring to the hot and cold seats which I did (see here kzfaq.info/get/bejne/ad6IibN5ktfTf3U.html)