How to Install Barrel on a AR10 | Aero Precision M5 Build

Рет қаралды 20,019

Күн бұрын

Today we’re going over a 18” Ballistic Advantage Barrel for our Aero Precision Enhanced Upper Receiver build. I hope this is helpful!
#aeroprecision #howto
Need more gear? Check out PSA and Brownells below:
✅PSA: alnk.to/3cln15m
✅Brownells: alnk.to/90yno2o
Use code 1stShot10 at Brownells
🚨List of recommended products I use:
campsite.bio/1stshottactical
Let's connect! Support me on Patreon! : / 1stshottactical
Orrrrr you can support the Channel by becoming a Member! :
/ @1stshottactical
Timestamps:
00:00 - Parts & Tools
01:59 - Install Barrel
03:42 - Torque Barrel Nut
This video is for educational, demonstration, and cleaning purposes only.

Пікірлер: 35

@NeverGone23 23 күн бұрын

Real Avid has an AR10 retention rod.

@timothydahlin5321 11 ай бұрын

Good deal on shootingsurplus for the vise block.

@Mongorat 4 ай бұрын

How easy is it to remove that enhanced piece? Cos I have one M5 coming, but will put on a Hera IRS Quad on it instead.

@ryanmatty7142 8 ай бұрын

😂 Great video on “How to NOT install a barrel “……. Just as educational as a “ how to” though. 👍🏻

@kelpo8455 7 ай бұрын

Can you explain why?

@liggerstuxin1 3 ай бұрын

Yeah, what parts are you criticizing? The way he uses his torque wrench is my guess.

@RascalCatify 11 ай бұрын

Out of curiosity, what is the reasoning behind torquing then backing the nut out until final torque? I get sneaking up on the final number, as is done a lot with working on cars, but never have backed something out to just torque it higher again.

@bigappa1862 10 ай бұрын

In layman terms... double torqueing accounts for bolt stretch and helps prevent it from coming loose/losing the desired torque spec. Think of it like a head bolt.

@joshuacruz4046 9 ай бұрын

It’s because it stretches

@wbrennan2253 Ай бұрын

I did that when I installed mine. All the information I had read recommended it.

@daverstewartjr5785 7 ай бұрын

You know that vice block is supposed to be 2 pieces. One piece goes into the upper and that vice block bolts to the piece into upper.

@dillionclayton2152 3 ай бұрын

Yep.... the other part is meant for applying torque to the barrel nut. I wouldn't copy this guy...

@dillionclayton2152 3 ай бұрын

Yeah.... the part that goes inside the upper is made for tightening the barrel nut. So you don't put unnecessary pressure on the aluminum upper receiver. The way he has it, is mostly used for cleaning or installing other accessories other than a barrel.

@wbrennan2253 Ай бұрын

I had to thermal fit my barrel. I put the barrel in my freezer for a couple of hours then used a heat gun on the upper. I had maybe 10 seconds to get it seated.

@NeverGone23 23 күн бұрын

Seems a little excessive to seat a barrel. I wish I would have know this about the enhanced upper before I bought it. What brand of barrel do you have?

@grandtheftavocado 11 ай бұрын

Do you have to time the barrel nut to let the gas tube pass? Also do people bed and lap their barrel for these types of builds? I haven’t seen anyone do it on the enhanced M5 upper.

@jacobpayne1723 10 ай бұрын

I just did mine today and after torquing, there was a rib right in the middle and wouldn’t allow the gas tube to go past it. I shaved that one rib down with my Dremel to allow the gas tube to go in. I didn’t really see another way around it.

@grandtheftavocado 10 ай бұрын

@@jacobpayne1723 Thanks man. I have used barrel shims before to time the nut, but I think I'll just dremel too

@MrPiimpslap 6 ай бұрын

@@jacobpayne1723 lol, you could've shimmed or tighten a bit more, since the torque value for a barrel is a spread, and not an exact number.

@BuffaloSoldier- 8 ай бұрын

How much is that vice and what brand ?

@chuekaothao6329 9 ай бұрын

LOL, some people using anti-seize while some other using loctite to lock it in place.

@Gunfighter5 7 ай бұрын

IT IS NOT RECOMMENDED TO USE LOCTITE !!! THE REASON FOR LOCTITE IS FOR WHEN YOU CANNOT TORQUE A PART!! NO REAL RIFLE MANUFACTURER WILL RECOMMEND USING IT AT THIS POINT. I laugh when people use blue loctite on gas block screws. That shit will turn to powder after one day of shooting. It would help if you had a high-temp thread locker like Rockset.

@BadDadio 2 ай бұрын

Loctite LB 8060 is a thread lubricant and anti-sieze

@John_Doe_6996 2 ай бұрын

But how to remove a barrel that is STUCK? Like really stuck…

@tollav Ай бұрын

HEAT!! LOL That will more than likely work. Is the barrel nut stuck or is the barrel itself in the receiver?

@John_Doe_6996 Ай бұрын

@@tollav the barrel itself was stuck in the receiver. I successfully got it out with no damage, used a pvc pipe through the receiver, and smacked the F out of it with a hammer. Tried the same thing with a wooden dowel at first, but the dowel kept breaking.

@marcmeadows6103 2 ай бұрын

Love how you skip important things

@davidcampbell2661 5 ай бұрын

Your loc tite looks more like never seize

@BadDadio 2 ай бұрын

Loctite LB 8060 is a thread lubricant and anti-sieze

@toddbernal2183 11 ай бұрын

Technically you over torqued it. 65 foot pounds is measured at the head of the torque wrench. There's another 1-2 inches added to the length of the wrench. Torque multiplication means it's going to be more then 65 foot pounds. Will it matter, no absolutely not. Just sayin. You can find conversation formulas on line if you want to know what you torqued it to.

@user-gs6bi3pm5c 11 ай бұрын

If the torque wrench is orthogonal to the crows foot, there is no need for math.

@lkazanov 8 ай бұрын

90 degree to craw foot, is the torque at the wrench