How To Install CROWN MOLDING using

Рет қаралды 1,116,376

Күн бұрын

Using the SAWSET PROTRACTOR with any t-bevel and miter saw, handymen and DIYers can learn how to install CROWN MOLDING easily and accurately for a perfect fit, every time. SAWSET PROTRACTOR - SOLD ON AMAZON This KZfaq video will give you, tips on how to measure, find angles, cutting with a miter saw, nailing, caulking, seams/scarf joints, end cap/returns, inside and outside corners, filling holes, gluing, and much more!
It will also show you how to use this unique carpenters protractor that has been redesigned to be compatible with any miter saw. Unlike a standard protractor it's scales have been calibrated to give perfect miter saw settings every time with absolutely NO MATH NEEDED! It is large and easy to read so finding fractions of angles is possible for that perfect fit.
To get that professional look when installing Crown Molding, Baseboards, Wainscoting, Stairs/Railings, Hardwood Floors, Decks and Fences, SAWSET PROTRACTOR and your sliding t-bevel will always give you those perfect angles. It is also an essential tool in your wood shop and in your tool belt!
The miter saw cuts at a fraction of degree, so why not have an angle finder that can do the same? This tool is the perfect companion for your miter saw. If you own a miter saw, you NEED a SAWSET!
Your Miter Saw is designed with 2 adjustable angle settings. One at the back, which enables you to tilt/ lean the blade, which gives you the bevel setting. The other is on the front of the saw parallel to the table, to adjust the miter setting. These settings done correctly, will give you that satisfying perfect fit!
The Sawset Protractor is able to find the saw setting for every condition with no calculations necessary.
SAWSET PROTRACTOR - The perfect tool for the perfect job!
Thanks for watching and keep checking for more How To Videos.
Please subscribe and leave your comments or questions below.
For more info about SAWSET PROTRACTOR see our website.
www.sawset.ca/
Sold on Amazon.com
www.amazon.com/dp/B0C9V6S411
Sold on Amazon.ca
www.amazon.ca/Protractor-Alum...
Purchase the New SAWSET PRO PROTRACTOR on our website.
www.sawset.ca/where-to-buy
TIMESTAMPS:
0:00 Intro
0:46 Find your measurements and miter saw setting.
1:53 Cutting your angles on the fence.
2:30 Installing your crown - gluing, nailing and tips!
4:55 Making a return or end cap.
6:20 Caulking tips.
7:20 Making seams perfectly!
9:43 Outro

Пікірлер: 446

@tomshieldsmith9687 2 ай бұрын

Watched 4 videos before I found this one. Could've saved myself half an hour if I found this first! Very helpful. Thanks!

@SawsetTools 2 ай бұрын

Thanks. Glad to be helpful.

@spicyhot1695 4 жыл бұрын

I wish I had seen this video 5 years ago when I installed my crown molding, it would have made the job a lot easier. Great video. Thanks for sharing

@SawsetTools 4 жыл бұрын

Thanks for your comment.

@sealcycle2020 3 жыл бұрын

I WISH I SAW THIS VISEO 1,000 BOARD FEET AGO

@cassiellightman 3 жыл бұрын

One of the best videos teaching how to cut crown molding. Thank you!

@SawsetTools 3 жыл бұрын

Thanks for the compliment.

@PerfectPicture2012 4 жыл бұрын

What a great detailed video, good job on molding and video!

@SawsetTools 4 жыл бұрын

Thanks for the compliment.

@ringokissu 5 жыл бұрын

Great video! My husband found this very useful. Thanks!

@SawsetTools 5 жыл бұрын

Thanks

@patrickmayer9566 5 жыл бұрын

Mr,jordan,,,thanks for this vid,I used this on my new job,just starting,you showed me just what I needed!simple,to the point,can't wait to have a nail gun!old school😐..also how to glue and clean up!!!!a plus...land o ' lakes,wi.usa.

@SawsetTools 5 жыл бұрын

Thanks Patrick! Good luck on your project.

@mary-bethdouglas2936 5 жыл бұрын

Great Video, gonna get this for my husband for sure

@SawsetTools 5 жыл бұрын

Thanks!

@lordbyron4163 4 жыл бұрын

Nice.... Thanks for this one. Been dying to attempt my victorian coving.

@deldeek 4 жыл бұрын

Yet straight to the point i didn’t see and explanation how you placed the crown on the miter what side for which ( left or right ) , from which point to what point you measure the molding ! That’s where the struggle is ...besides that thanks for sharing

@SawsetTools 4 жыл бұрын

Sorry. Limited time.

@toreyyoung1518 4 жыл бұрын

#1 you are very informative. #2 great detail #3 I had long hair for Years. Ponytails men & women. Buns...female ballet dancing.

@SawsetTools 4 жыл бұрын

Thanks for your positive feedback!

@u.sonomabeach6528 Жыл бұрын

Thought I was gonna be surfing videos for hours but your video had me back working quick. Thank you for being competent, clear and concise! One thing I will say though is there IS one person who wants to be called stumpy….Stumpy Nubs Woodworking channel 😉

@SawsetTools Жыл бұрын

I love Stumpy Nubs!

@SawsetTools Жыл бұрын

Thanks for the compliment.

@mrdman094081 4 жыл бұрын

Agreed. You make it look easy and uncomplicated, the opposite of what it is. That's a skill.

@SawsetTools 4 жыл бұрын

Thanks, years of repetition.

@alaverga3455 4 жыл бұрын

Make it look so easy, this guy is a pro and is very skilled👍

@SawsetTools 4 жыл бұрын

Thanks, I do it for a living.

@matthewo755 5 жыл бұрын

Great video, lots of helpful tips. Thanks.

@SawsetTools 5 жыл бұрын

You're welcome!

@bennyholguin7032 3 жыл бұрын

Thank You for the video. It was Very Informative! You made it look EASY!

@thetoolman3355 3 жыл бұрын

Thanks Ben for the Compliment.

@foreignercatracho 4 жыл бұрын

Thank you so much for sharing your knowledge. I learned a lot of tricks

@SawsetTools 4 жыл бұрын

Thanks for your compliment.

@cynthiaescobar3762 4 жыл бұрын

Great advice! I learned a lot!

@cloudflores9838 4 жыл бұрын

Oh wow this video was fun, easy and very informative to watch! Thanks man

@SawsetTools 4 жыл бұрын

Thanks for your positive comment.

@BlankHouseCoLLC 4 жыл бұрын

Very good tutorial and simple explanation. I was sharing this with one of my helpers to help better explain the concepts of setting crown and how measurement increases are very important so you don’t burn material by 1/8” or 1/4” trying to get a fit inside corner/outside. 👍🏻

@SawsetTools 4 жыл бұрын

Good call.

@ricardogalvan6700 Жыл бұрын

What type of glue are you using

@ScubaDiverMagazine 9 ай бұрын

Took ages to find a decent video like this. Thanks.

@SawsetTools 9 ай бұрын

Hi to the UK. Thanks for taking the time to comment. Glad the video was helpful.

@thetoolman3355 5 жыл бұрын

Very informative video, thx!

@SawsetTools 5 жыл бұрын

You're welcome!

@BigmoRivera 4 жыл бұрын

Great Tip Nice Work... Awesome Tool. 👍

@SawsetTools 4 жыл бұрын

Thanks for you input!

@salompita 4 жыл бұрын

You make it look so easy but at the end it’s beautiful

@SawsetTools 4 жыл бұрын

Thank you for your nice comment Jenie.

@zaneh6188 5 жыл бұрын

GREAT VIDEO, Well informative. Thanks

@zaneh6188 5 жыл бұрын

where can i find that clamp or metal plate on the Dewalt miter saw? i have the same saw

@SawsetTools 5 жыл бұрын

@@zaneh6188 it's called "Crown Stop". I bought it at Lowes. It's also available on Amazon. Thanks for your comment!

@maureenmellegers6582 2 жыл бұрын

Great video on installing crown molding.

@SawsetTools 2 жыл бұрын

Thank, Moe

@SassyHilda 4 жыл бұрын

You made it look so easy.. impressive detailing

@SawsetTools 4 жыл бұрын

Thanks Sassy.

@normajk2 3 жыл бұрын

Thank YOU !!! very helpful !!! Good Job !!!

@thetoolman3355 3 жыл бұрын

Thanks for the compliment.

@Nicole-fj3pt 4 жыл бұрын

Beautiful

@SawsetTools 4 жыл бұрын

Thank you! Are you talking about Jordan, hahaha!!

@DiannaAtherton 3 жыл бұрын

Finally a video on crown I understand. I was so confused about turning crown inside down before cutting. Thank you. Can you share what glue your used? Thanks

@SawsetTools 3 жыл бұрын

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works. Thanks for your positive comment.

@luisbanda7063 2 жыл бұрын

THANK YOU , WONDERFUL TIPS ON THIS VIDEO !!!

@SawsetTools 2 жыл бұрын

Thanks for your compliment.

@madjack5002 4 жыл бұрын

Your skill is impressive. Thanks for the video. I bought the Kregs jig today. And all of the videos say to cut it top down. They left me wondering what the hell is the top and what is the bottom. Hopefully mine turns out looking like this. I bought about 40' extra just to practice with.

@SawsetTools 4 жыл бұрын

Thanks for the tip.

@bartonchu670 3 жыл бұрын

Jordan, Great video explaining how easy this protractor is to use and how accurate it can be. Well worth the $20+ and it is so compact for storage. Works simply with the T-bevel you likely already have. Your instructions on applying latex caulking to all joints and surfaces before installing the molding to ceiling and wall was so helpful to successful completing our room. When installing long pieces it is like a 3rd hand holding the molding in place while you position and nail. Super suggestion and a great help to ensure the piece is permanently held in place.

@thetoolman3355 3 жыл бұрын

Barton thanks for the compliment. Merry Christmas

@SawsetTools 3 жыл бұрын

Thank you for your positive feedback. It's so great to hear success stories and how Sawset and our videos have helped you improve your carpentry skills. That's our goal!

@yichalnegussie5401 4 жыл бұрын

Great Job in providing nice tips and tricks, I got answer to my questions Thank you

@SawsetTools 4 жыл бұрын

Thank, My pleasure.

@bryonsview 4 жыл бұрын

Thank you for sharing. This video was extremely informative. Way better than the old homes guy. Lol. I have to order that tool that allows you to measure angles.

@SawsetTools 4 жыл бұрын

Thanks for your comment

@robertosalazar3628 4 жыл бұрын

Master good job 👍

@SawsetTools 4 жыл бұрын

Thanks

@jeffreylonigro1382 5 жыл бұрын

Great video!

@SawsetTools 5 жыл бұрын

Thank you!

@moisesrobles7884 3 жыл бұрын

Nice work bro and tips thanks keep it up lm smashing my like botton katakabooooooooooooom

@SawsetTools 3 жыл бұрын

Thanks. Love that expression.

@seven73ify 5 жыл бұрын

Awesome! Thanks

@SawsetTools 5 жыл бұрын

Thank you!

@joseluismacias3878 4 жыл бұрын

Muchas gracias amigo muy bien explicado tu video aprendi bien todo, boy a empesar mi proyecto

@thetoolman3355 4 жыл бұрын

Thanks for your compliment.

@PVTOW 5 жыл бұрын

Awesome Video !!

@SawsetTools 5 жыл бұрын

Thanks!

@casperlokz8348 4 жыл бұрын

Good stuff!!

@SawsetTools 4 жыл бұрын

Thanks for your input!

@anthonykhan3424 5 жыл бұрын

Very good work tanks

@SawsetTools 5 жыл бұрын

Thanks for watching!

@JohnDoe-ft2nh 4 жыл бұрын

Great video.Thanks man.

@SawsetTools 4 жыл бұрын

Thanks for the compliment.

@ivankotarscak5014 2 ай бұрын

Simply best

@SawsetTools 2 ай бұрын

Thanks Ivan,

@jewelsbaby2449 Жыл бұрын

🙌🙌🙌 great job!👍🏽

@SawsetTools Жыл бұрын

Thanks, Glad you liked it.

@hakeemlayode1474 4 жыл бұрын

Thanks nice n really enlightened

@SawsetTools 4 жыл бұрын

You welcome.

@joelewis2401 5 жыл бұрын

Great video

@SawsetTools 5 жыл бұрын

Thanks!

@mregan3855 4 жыл бұрын

Great video,,

@SawsetTools 4 жыл бұрын

Thanks for the compliment.

@gamerm4876 4 жыл бұрын

Hey great video thanks for taking the time too teach us all how too do this . Question what size nails are you hitting that crown molding with ? Also what type of glue are you using ? Thx

@thetoolman3355 4 жыл бұрын

2 in. 18 ga. Brad nails, trying to hit the studs when I can. We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@paulinemonastero322 4 жыл бұрын

Your how to videos are the best we’ve seen as far as clear precise descriptions and make us feel like we can tackle it ourselves so thank you. Do you mind sharing under your descriptions, what wood glue you use as well as name of seem and hole filler please? This would help eliminate the guess work when we need to purchase.

@paulinemonastero322 4 жыл бұрын

Another note if you don’t mind, what model and where to purchase the mitre saw you are using and what the actual brackets you use to hold crown moulding in place on the saw table?

@thetoolman3355 4 жыл бұрын

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works. We use drywall compound to fill holes.

@thetoolman3355 4 жыл бұрын

@@paulinemonastero322 Any miter saws with a 12 inch blade is good. Each brand will have there own crown stop.

@bobdavis3389 4 жыл бұрын

Very good , informative , !!

@SawsetTools 4 жыл бұрын

Thanks Bob

@carmelojeronimo8497 3 жыл бұрын

Nice job

@SawsetTools 3 жыл бұрын

Thanks Carmelo

@miguelespinoza8602 3 жыл бұрын

I love it !

@SawsetTools 3 жыл бұрын

Thanks Miguel. It's always nice to hear a compliment.

@247videogame 2 жыл бұрын

👍👍 excellent!

@SawsetTools 2 жыл бұрын

Thanks!!

@rickwaldner8078 2 жыл бұрын

Im a fine woodworking carpenter by trade for the past 20 years, lots of good tips on this video, how ever, the ceiling you were working with was exceptionally good, most of what we come across is much worse with being off level and bade bumps / dips in the ceiling. it can get much more complicated at times.

@SawsetTools 2 жыл бұрын

You are right Rick. I have done a lot of old homes and plastered homes are the worst. I'm retired now, and that's my son on the video. Thanks for the comment.

@cancerenergy2464 Жыл бұрын

Great video💪🏽💪🏽

@SawsetTools Жыл бұрын

Glad you liked it!!

@Kaladesignbg 2 жыл бұрын

Great job!!

@SawsetTools 2 жыл бұрын

Thanks, always nice to hear a compliment.

@U2BER2012 2 жыл бұрын

Say...you're pretty good. I like this video; simple yet very insightful!

@SawsetTools 2 жыл бұрын

Thanks, I try my best.

@HaNguyen-iq8un 4 жыл бұрын

I like your video .

@SawsetTools 4 жыл бұрын

Thanks for your positive comment.

@zulmarosario1346 4 жыл бұрын

Nice video thanks for sharing. Can I only use glue my wall are plaster and I think it hard for those nailer

@SawsetTools 4 жыл бұрын

Plaster fractures when nailing. I recommend you nail to the studs.

@bbundy1069 4 жыл бұрын

Excellent video. Thanks for sharing.

@SawsetTools 4 жыл бұрын

Nice to hear.

@irisostachowski1489 3 жыл бұрын

Most silicon caulking's are NOT paintable. Be careful paint will not stick. We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@juanquintero3195 3 жыл бұрын

Great vid. What style, material, and how and size is the molding you are showing in the video?

@irisostachowski1489 3 жыл бұрын

We use a 5.5 inch wooden Georgian style.

@raycarter575 3 жыл бұрын

what size nail gun were you using? great job on the video! i'll keep coming back!

@SawsetTools 3 жыл бұрын

18 Gage brad nails x 2 inch.

@SawsetTools 3 ай бұрын

Have a great day.

@sams872 2 жыл бұрын

good video, thanks

@SawsetTools 2 жыл бұрын

Thanks for the compliment.

@toronto690 3 ай бұрын

What to do when the ceiling is not even, and the crown moulding titer totters? Which stud finder do you recommend. Need a reliable one

@juanfernandez8060 5 жыл бұрын

the video is wonderful. very good instructions. have a great success

@SawsetTools 5 жыл бұрын

Thank you!

@anilpodgornik8206 4 жыл бұрын

Nice video. I agree I pays of to measure corners beforehand. Just like to add that in my experience there's no need for a nail gun if using an appropriate glue. Although i use type of quick glue for the corners, wich means they stay in place, if the corner glue is slow acting ther is possibility of them moving out of place.

@SawsetTools 4 жыл бұрын

Food for thought!

@sharonhoare5790 4 жыл бұрын

Anil Podgornik I have never used nails in this way either. I only use them as supports underneath go stop long runs sagging, and then only if needed. Of course they get removed afterwards.

@lordbyron4163 4 жыл бұрын

Question. Can you install crown mouldings over walls and ceilings that have wallpaper on? or do you have to cut the paper away first ?

@SawsetTools 4 жыл бұрын

Yes, remove wallpaper and wash off glue residue.

@mattkoch1456 2 жыл бұрын

great tips thanks. looks like a small brad nailer, what guage/ length are you using and are you nailing into studs/ joists?

@SawsetTools 2 жыл бұрын

Hi Matt, Good questions. I used 18 Ga. x 2. (16 GA makes the perimeter of holes stick up) You try to hit the wood when you can. When gluing is done right, it gives a lot of support to the wood crown. (Keep in mind plaster crown moulding is neither nailed or screwed, yet it stays up.)

@H2oToGoWH 3 жыл бұрын

Nail hole tip ; use drywall putty, you can sand it lightly or wet cloth when it’s close to dry. I find caulking doesn’t fill that great, but that’s just me.

@thetoolman3355 3 жыл бұрын

You are right. Dryway compound is the best way. My mistake.

@janetcampbell5360 4 жыл бұрын

THANK you for your amazing informative information.

@SawsetTools 4 жыл бұрын

Thank you for your comment!

@knotallthere66 4 жыл бұрын

Caulking nail holes okay yea ya do it once in awhile ,best is quick dry Spackle goes in like butter and it’s sandable ,

@SawsetTools 4 жыл бұрын

You are right. Thanks for your comment

@barrygordon1173 3 жыл бұрын

And no glue on bottom of crown...brads only...want to be professional...

@AndyB718 4 жыл бұрын

You're Hired ! Ty for the video.

@thetoolman3355 4 жыл бұрын

Thanks for the positive comment.

@billzima7068 4 жыл бұрын

Need a cushion on that gun. I would highly recommend not caulking nail holes. Use a filler that wont shrink. I use a product i think from DAP but we push it in really good then just little on the heavy side. The filler is super lightweight and can really be sanded by hand. But we just run around tje room with a sanding sponge..it only takes a few minutes and it smooths out any of the crap primer job, the over fill of filler we applied and makes splices and outside corners flawless. Also dead end returns we use CA glue and put it together on the bench b4 it goes up. Blocking,splices and outside corners use wood glue!! Inside corner we cope and then apply a small bead of caulking with adhesion b4 fitting together. Keep everything clean as you go. I like having a wet sponge with me but only to keep my finger clean and moist to slick over the caulking. Crown molding is one of them things where it can be tough in the beginning but when that lightbulb goes off in your head and you totally understand it ..it then becomes as easy as installing baseboards. Very nice angle finder..with that and a bevel gauge you are guaranteed a beautiful outcome. Happy building all!!:)

@SawsetTools 4 жыл бұрын

You are right. Thanks for the helpful tips.

@locatejohn 3 жыл бұрын

What's are your thoughts MDF and non-MDF crown moldings material?

@irisostachowski1489 3 жыл бұрын

Wood does a one time minor shrinkage, because of moister content in the wood. I use MDF, because doesn't shrinkage. Recommend oil prime before painting wood or MDF. This keeps moister away from wood.

@robertsoobramani202 4 жыл бұрын

What type of glue do you recommend for installing crown mouldings?

@SawsetTools 4 жыл бұрын

We have always used a water base glue, such as Lepage No More Nails.

@sarahscarola4008 3 жыл бұрын

Any suggestions for a glue brand that would comparable to Lepage that is available in the US? Picked up Loctite All Purpose but it comes out as a foam and is very awkward to use.

@SawsetTools 3 жыл бұрын

Sorry, being in Canada not familiar with your product brands. Any product that are water based and paintable would be great.

@fredsanford6143 11 ай бұрын

Hello, Love the video. About to start a crown moulding install. The previous owner didn’t want to finish the crown, and stopped with a flush cut on an inside corner 3:10 3:10 . I understand it’s best to use a coping saw, but how do I cut the moulding and get it to matchup? Thank you

@SawsetTools 11 ай бұрын

I know the traditional way is to cope, but mitering is the best way, because the 2 moldings lock each other in place. If the existing crown is not glued down, I would remove it and miter. Mitered corners are also crisper.

@abbyhernandez916 4 жыл бұрын

Hi I live in Arizona do you travel this way..?

@SawsetTools 4 жыл бұрын

Hmmm?

@wadeshimojo 4 жыл бұрын

You have any crown molding holder for the one person installation?

@SawsetTools 4 жыл бұрын

When I'm alone I brad nail or screw a 2 by 4 in the corner for a temporary support.

@wvoyles 4 жыл бұрын

i do returns in a 3 piece joint,with saw at 22.5 degrees,and i use CA glue with an activator,looks a lot better than a 90 degree return

@SawsetTools 4 жыл бұрын

I like that look. Will try it sometime. Thanks

@billzima7068 4 жыл бұрын

I do mine same way. I did the 45° returns for so long and seeing the same thing in every house..i wanted a different look.

@SawsetTools 4 жыл бұрын

@@billzima7068 I will definitely try it next time. Thanks

@atillausta8514 2 жыл бұрын

Very good thans

@SawsetTools 2 жыл бұрын

Thanks again.

@sheriwormsley9313 4 жыл бұрын

Would you please come to my house and install my crown? Amazing work !

@locatejohn 3 жыл бұрын

Is the caulking material made specific for MDF glueing?

@irisostachowski1489 3 жыл бұрын

I don't believe there is a calking for MDF. We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@SawsetTools 3 ай бұрын

I use a cordless drill, with a fine bit to find studs.

@squareheadconstructionllcf3327 4 жыл бұрын

I really need a sawset tool

@SawsetTools 4 жыл бұрын

You can order it from our website... sawset.ca

@anilpodgornik8206 4 жыл бұрын

Cicrular saws are limited.. You can only cut 7-10cm in heights, so when you come upon cornice mouldings that are bigger it is useless. There are hand saw kit for bigger mouldings. Simple ones for - 45 90 +45 degrees and also adjustable ones... For small or flat ones circular saw is much faster though...

@briangordon1767 3 жыл бұрын

Sawset tools I can't find any web site where they ship this tool to Ireland or UK can you please help me

@leeoien3645 8 ай бұрын

How about a short video on what to look for in a miter saw and other critical tools?!

@SawsetTools 8 ай бұрын

Something to think about. Thanks

@ericcharp4388 3 жыл бұрын

Easy peasy. Ya right!!

@thetoolman3355 3 жыл бұрын

Eric, patients is the key.

@ECO-AFRO 2 жыл бұрын

Wow! If you know, you know

@SawsetTools 2 жыл бұрын

Thanks

@jmmartin204 4 жыл бұрын

What brand glue are you using ?

@SawsetTools 4 жыл бұрын

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@CornelioAustin Жыл бұрын

Nice

@SawsetTools Жыл бұрын

Thanks

@rodralph824 2 жыл бұрын

Great video. You might indicate which "glue" you are using.

@thetoolman3355 2 жыл бұрын

Hi Rod, We use La-page No More Nails. Any dense glue would work.

@negative5009 5 жыл бұрын

Wonderful tip I’ll be doing my house Wat kind glue you sugest Thanks 😃

@thetoolman3355 5 жыл бұрын

The glue I use is "No More Nails" by Lepage

@SawsetTools 5 жыл бұрын

Thanks for your comment! Use a thick glue, not liquid. Same glue as Tool Man.

@joseleal9134 2 жыл бұрын

I am stuck on one thing, when you show the tutorial at 5:14 you do not say how to cut the first piece you show in the tutorial. So basically the piece that you put that small little piece on. I do not know how to cut that piece so that the little piece fits perfect. Some help and clarification would be very helpful

@SawsetTools 2 жыл бұрын

Sorry Jose, in the editing it was decided not to create a long video. So I couldn't show every detail. Go to sawset.ca Videos and Tips. Look under Template and the piece you are referring to is the 5th picture.

@RushWorkingMan 4 жыл бұрын

Can you show how to install crown molding on a sloped ceiling?

@SawsetTools 4 жыл бұрын

Yes, if I run into that type of job.

@davidmatias6239 4 жыл бұрын

What type of glue do you use

@SawsetTools 4 жыл бұрын

We use Lepage No More Nails for gluing, and Dap WATER base calking for the final part. But any WATER base glue that comes in a calking tube works.

@jerrypelletier2328 3 жыл бұрын

I always cut crown holding the crown flat on my chop saw.

@thetoolman3355 3 жыл бұрын

See our other video. (How to Cut Crown Molding ON THE FLAT using Sawset Protractor.)

@bolerdweller 3 жыл бұрын

I do too. Most accurate way to do it

@dmlvsccfamful 3 жыл бұрын

Sawset makes the most accurate joints,I've used all the other gauges and none are as good

@SawsetTools 3 жыл бұрын

Thanks for your comment. Accuracy is what we strive for.

@dmlvsccfamful 3 жыл бұрын

@@SawsetTools my clients are amazed at how tight my baseboards turn out even without any caulking

@SawsetTools 3 жыл бұрын

@@dmlvsccfamful I was a contractor and my son still is. Praise from a customer is always good.

@genekhuc8824 Жыл бұрын

Hi very helpful however do you cut 44° from one side only or from both sides?

@SawsetTools Жыл бұрын

Always cut both. Also positioning of crown on the wall is important. To high or low on the wall could gap top or bottom. Adjust it to find that sweat spot.