For me, the ideas in kzfaq.infoUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.

Very clear instructional examples. The 3D work and narrator made it really clear.

This is the most informative well made video for roof installation I have ever seen.

😂 the effort put into this video lends it credibility it really doesn’t deserve. The ends of the panels get hemmed and hooked to the correct drip edge for the panels, drip edge also isn’t correct. Come on guys, a homeowner might make me do something like this to their home after watching something like this.

I think everything is right on with this video..there is alot of sealant on ever peice installed pretty good video.

Grace Ice and Water is your best friend here and precision sealant application on the uphill sides of the roof penetrations where you slip the flashing under the roofing. I have this system in Ketchikan, Alaska and it's a great install. Get the right contractor.

ALL info videos need to be presented so well..TY TY . WATCHING EM FOR LONG TIME..BEST FIND. I GET IT..EASY TO FOLLOW SIMPLE AND CLEAR INSTRUCTION.....TY TY.......any other build videos available ?

Watching Doha Qatar. Thanks you 4 shering.

This is a great roofing product. Installed it many times. It’s great.

This channel deserves a lot of subscribers

roofing instructions for the house, detailed standards, I thank you for your guidance

WOW, very informative, can pretty much use most of these techniques on any type of metal roofing. Thank you ASC

Is it sound proof when there in rainy season

AGUARDAMOS ESTE EXELENTE PRODUTO NO BRASIL

Excellent job, this serveries is available in Pakistan?

The order of operation is a little off in this video. At 3:30 they jump into the vented ridge cap...but at 4:50 it demonstrates the gable end flashing, which must be done BEFORE the ridge cap. The zee closure goes on before the gable flashing because the gable end is cut to accommodate the zee closure at 5:08. But the ridge itself is positioned OVER the gable flashing.

I watch this video on repeat to help me fall asleep.

I'm not judging, but you're putting holes through your metal to attach it to the roof. Not only that, but the panels snap together like a model kit. It looks good in a computer program or on new construction, but reality is alittle different, especially with a rip/replace job. I recommend 24g 1" drip edge, 21" wide double lock standing seam with wrapped corners, rake edge and eaves. It comes in a variety of colors and metal, from galvalume to copper, zinc to steel. In the end, everything wraps itself with nothing exposed. It even eliminates the need for reverse flashing for walls, skylights, chimneys, etc.

Good good JOB and good video

watch from Bogor Indonesia

Great video!

Very nice video. I don't like your chimney flashing. Old school method is to cut into the mortar between the chimney bricks to achieve a diagonal zig-zag mortar notch. Then you fold the flashing into the cut channel and seal. Sometimes they just cut a diagonal straight line across the bricks, which is better than what you show in your video, but this can cause a stress concentration that could cause brick cracking. In your method, as the metal along the chimney vertical flashing seasonally expands and contracts, the caulk with work loose from the chimney brick and water will leak in. I am also nervous about all of edge screws you apply through the metal roof. A more thorough design hides 100% of all screws so that there are zero screws exposed to the rain, even if rubber washers are installed under each screw, the rubber will decompose.

How do the 2" notches above the skylight in the last video not leak?

Very excellent video.

I guess it doesn't rain where you're at..

Great Video, very clear instructions. However at 11:48 can you confirm you do not secure the vertical face of the peak flashing with stitch screws?

古民家でも日本瓦を撤去して代用できますかお金がかかりすぎで悩みです

Nice video 👍

You can still see the underlayment from the notches cut above the chimney and skylights. Are those holes suppose to allow water in for job security?

Thanhks thanhks bạn. Thật sự tuyệt vời

Very good ideas thanks

The material available sales in Malaysia....?

Muito bom! Excelente.

Junk installed will have problem with leaks

What about this gab?

Very good product, but shouldn't the ridge cap be sealed at end. The folding of materials and seating on top with no overlap seams to be a place to infiltration during rain/wind (5.25 min/video)?

Классная крыша! Но мне кажется учтено не всё! Над дымоходом лист идёт в нахлёст без доп ленты или бортика!

Oggy Bleacher To be honest I built a garage eyebrow which is just a 2 ft overhang above my doors so did not have to do any ridge venting. Just worked flashing under siding. Good luck on your project.

How did they not get caulk all over the place?

Very well said amazing but it does cost a lot

formidable la forma de instalar

THAT Z CLOSURE SHUT OFF THE VENTING,,,,BAHAHAHA REAL GREAT

not sure about the counter flashing @ 10.00, is it not usually done by chasing out the mortar joint in the brick and sliding the counter flashing into the joint and then repointing it?

The top pan flashings on chimneys and skylights always leave a 1/4" hole in the panel. This is a failure! I prefer to run the head flash all the way to the ribs left and right and overlap panels.

10:44 what about the gaps left in the corners above the chimney and skylight where the flashing slides under the piece above it. theres gaps at each corner where water wiill make its way under. there is no explanation on how to seal this

Really good in 3D explanation but on the wall the actual happening during rainy time its a disaster leaking coming from the wall even u apply sealant not long lasting

How much for standing seam metal roof for 1000 sq ft house?

Полезная информация!

Point is not to use exposed screws. Potential leek do extreme weather changes.

Comment se présenterait le travail avec des panneaux sandwichs ?

Talorahat menee vesikatto rakenteisiin, kesä menee vesikaton tekoon !

Super

New subs..idol nice po

Why put screws exposed in standing seam roof? How is ridge going to breath with perforations on top of flat bend, attic air can’t get to it. Might as well put a cheap screw down roof it would be as cost effective. I don’t have one fastener exposed in my standing seam installations

Nice video. but Tape and caulking? I never thought a roof should be caulked? And for the tape or any kind of seals, don't they deteriorate over time?

Это конец прошлого века..!

Aroud chimney it is wrong here

Hi! Does anyone know what kind of software is needed to make a video like this? :\

I like it

Belarus 2020-2021 Zabudova

Salam Aleycum lesco master

9:10🌧

Problem I see here. If any water gets thru the fasteners it is going to run down and UNDER the edge flashing.

At 1:36, this guide tells you to install a line of screws through the panels and into the edge of the eave -- one of the first places roofs leak. If you want an el cheapo exposed fastener roof, why pay for standing seam?

what is this animation video

Todo bonito pero no pusieron los klip de cada perimetro

Mantab broooww

Silicone to seal of the bottom hole on the valley pan ? This is their answer for that ? Fail

primo roof job

хорошо

water seal in the chimney it's very bad

Good in only in termite free regions...

5:38,и 5:56...почему низ угла ендовы в разные стороны?? 😂😂

Macht das aber nicht in der Schweiz🇨🇭.Danke.

I Watch on peice installed no brazil

Show 🥰

You never should put so many holes for water to enter a roof as I see with this product? then of course every screw is a potential leak point. Even with a rubber washer, the washer would dry out at some point? all the tape use has to be another source of leaks. Over all I would never use a roof system like this. It just seems so counter productive to apply and the holes, screws and tape to seal a roof to me?

Min 3:44 no es mas facil que valla asia arriba cortar la ceja del primero

Either do an exposed fastener system or a concealed fastener system. I don't see the point in hiding screws in the nail strip if you're putting exposed screws in the eves (the part of the roof that receives the most water). Same goes for flashing and ridge. I just don't understand why you wouldn't hook into your z and hide your fasteners. As others said chimney should be cut into and counter flashed. This is honestly just a messy job.

No screws over the panels😅

'Clear as mud! 'Terms are not explained.

👍

The bottom peice needs to go on first, thats gunna leak

Union Corrugating did it better. Spangler TV does it best. Just saying....

Как а сказке система супер.

Good. I want to Subscribe your channel.

Thank fuck they invented corrugated iron

halo., como consulta y mi opinion, las personas pagan muy altos costos de la constructora minimisan sus medidas de seguridad. el techo de este video esta separado, las fuerzas de. aire y de tornados asi como lluvia, arena y nieve, son nuy especciales por zona no se permite anclajes de espacios y al poner teja enlonar con material flexible y duradero pues se ancla separado. para la techumbre de acero y teja. no me agrada ver asi el trabajo. sus razones las respeto. 💯✍️

FAR to much use of exposed fasteners along the eaves and valleys for a roofing product that is designed as an overall hidden fastener product. Use a metal roofing drip edge and valley with Z hem, then fold a hem in the end of the roofing panels. This eliminates the exposed fasteners in these areas of high water shed concentration. This type of installation locks the panels into place and will keep wind and wind blown rain from getting underneath the roofing panels at the eaves and valleys.

This video is wrong. The drip edge should be installed under the felt not over.

铝铁混合结构。

Too complicated.

Never use exposed fasteners. Bad practice. GL all.

It's "roof" not "riff".

In a high wind situation, your whole roof will unpeel and blow away. You cannot leave a weak spot for the wind to get into. Terrible idea. Plus it will not help cool the attic, other methods are necessary.

Да ну нах

10:42....fail.

I was very disappointed in your video. If you’re going to describe all this want to tell locations with this product can be purchased. Or list people who can install it for you. There’s too much information left out of the description below

Dumb! Why you exposed fasteners on a standing seam roof. You should do a 1” bend on bottom of panels and bend around the drip edges. Also you should use rake j so that your gables can be riveted in. Please do not install like this

Get off my phone