How to install PVC Bathroom Wall Panels

Рет қаралды 413,431

2 жыл бұрын

National Plastics show you how easy it is to transform your bathroom with PVC bathroom wall panels. From which tools you need to install and how to measure, this video shows just how straightforward it is to make your bathroom dream a reality.
Browse and buy our selection of bathroom wall panels online: www.nationalplastics.co.uk/wa...
All of our bathroom wall panels can be delivered direct to your door and we offer FREE DELIVERY for all purchases over £100 (ex vat). You can also purchase direct from one of our nationwide branches, visit us today.

Пікірлер: 50

@CoolDude-tz5co 2 жыл бұрын

Excellent video, gets straight to the point with no nonsense, thanks

@terrybenedict1 Жыл бұрын

VERY DRAMATIC

@cokhitonghop9256 2 жыл бұрын

Well done

@czeital Жыл бұрын

Good start but nothing on how to get that width cut correct if you need whole panel to corner - ie: if things are out of square etc and also are panel widths stated in/ex tongue and how are trips accomodated in width calcualtion. Also saw nothing on how to deal with the bottom when it's meeting a bath which would be great to know thanks

@pvclover76 11 ай бұрын

Do I need to put a bead of silicon in each side of the corner trim before pushing the panels in ?

@shaidanasreen134 7 ай бұрын

What about around the bathroom window or is this just suitable for straight wall, if you can pleas make video

@evashell 5 ай бұрын

Can you stick on top of old tile.As i will be using it as a kitchen splash back.

@dobarjepostenje662 11 ай бұрын

Can you put this wall panels on any type of wall? If I start doing this on which things I should be careful about

@flexhex3334 11 ай бұрын

what panel is this, im looking for it on your website and cant find it. Many thanks

@user-yk5zz1gt9v 10 күн бұрын

Can this be applied over wall paper?

@thespecialist7 Жыл бұрын

Hi should you prime the wall first ,I am using plasterboard. Using Silicone to stick the wall panels. Or can I just plasterboard the wall first?

@NarrowboatSuperB Жыл бұрын

If you have plasterboard that has not been skimmed, just use PVA, mix pva with water, brush it onto the board.

@nairagasparetto Жыл бұрын

It could be installed on a existing tile wall?

@alistermcnicoll2634 Жыл бұрын

If putting on top of existing tiles is there not a problem of getting pipe connections of controls etc through the extra thickness?

@NarrowboatSuperB Жыл бұрын

Most of these boards are 5mm

@ebayseller6040 4 ай бұрын

can I make a table using this??

@Lilyhenbury1 4 ай бұрын

Can I put wall panels over Artex?

@asmarahi3311 Ай бұрын

Can we do colour on pvc panneling

@Xan-zh5ni 4 ай бұрын

Hi how would I replace a damaged panel?

@vcsradio2805 2 ай бұрын

Good job. Can this board be applied to a cement wall

@gregc7699 29 күн бұрын

Yes

@sosolife 2 жыл бұрын

☺️👍

@brrymcgolly Жыл бұрын

Oh yes it looks very easy but they don't tell you about the awkward cuts when you get to the end. You can't guarantee not all bathrooms a square.. but a very good video

@ealingbroadway2000 10 ай бұрын

That’s why you measure, we had height differences that went into a slant from corner to corner, that was a real pain

$@frackend9035$

@frackend9035 11 ай бұрын

ONE HUGE PROBLEM! THEY DON'T HAVE A STORE IN U.S.A?

@aimansaleem6166 Жыл бұрын

What is the material of these pvc?

@silverbackag9790 Жыл бұрын

PVC.

@sophiemagsx Жыл бұрын

Hi , are you in London? Would you fit this for me x

@Andrew_Tate_Personal 5 ай бұрын

No. We are busy!

@svkscorpio Жыл бұрын

Doesn't water seep in between the panels and cause the wall to dampen and also growth of mold behind them?

@chrisbelfast6662 Жыл бұрын

No because you will use trims for the ends on the panels so it's water tight

@alanoliver5378 8 ай бұрын

As instructed in the video, apply silicone sealer to the TnG joint of each panel.

@privatechannel8462 6 ай бұрын

@@Parkertannerzi did this, then found out it was me

@ealingbroadway2000 5 ай бұрын

PVC cladding panels come in different sizes, mine were 8’x4’ and easier to work with, only needed 3 and shorten height on them.

@davidhayes1950 Ай бұрын

The pannels are tongue and groove and the bead runs round the side but don't bother measuring the bead just scribe it off the aqua panel that you have cut ready to put in and your adhesive should be put on like dot and dap and don't bother putting the nozzle on your adhesive as you need it to come out in big blobs once every 150 mm across and down doesn't have to be a exact and avoid putting the adhesive near the edge as it will squirt out around the edge of the panel but do put the nozzle on the silicone and do a bed of silicone were your gonna place the qua panel which will give you your added protection but make sure you wipe off clear any smudges of silicone/adhesive that get on your board showertray/bath because you want to put a neat bead of silicone on after the install is complete I install these all the time so any questions just ask