No video
How to install the Mosselman oil thermostat into your BMW S55 M2, M3 or M4!
Рет қаралды 5,506
Күн бұрынHowdy all!
Check out my new branded gear!
www.ebay.com/s...
Lillith: The F87 M2 Competition build out
f87.bimmerpost...
Furiosa: The F32 435i build out
f30.bimmerpost...
Properly maintaining your car, and especially the cooling subsystems is vital in a high performance motor. This is especially critical if you also decide to tune your car, and take it beyond typical factory specifications.
Arguably the most important subsystem in your car is the oil itself, and maintaining that is vital. I see the Mosselman oil thermostat as a critical piece of that, and I wanted this in my S55 M2C for sure.
The install really isn't that hard, and something you can do in less than an hour with a few simple tools.
Required parts and tools:
Mosselman S55 Oil thermostat
www.mosselmant...
or
www.kiesmotors...
10mm, 13mm sockets and wrench
T5 allen or socket
T35 torx driver
E8, E12 reverse torx socket
torque wrench
Plastic trim tool set
pick tool
Torque values:
Front and rear CF strut bar bolts: 28nm
Bolt holding oil return pipes: 8nm
Oil‐coolant heat exchanger to oil filter housing: 16nm
Nice to have:
Good lighting
www.amazon.com...
Great music - Larkin Poe is just amazing, check them out!
www.larkinpoe....
@salimbaksh380 10 ай бұрын
Thanks!
@BMWDIYGuy 10 ай бұрын
Thank you!
@chriszachmo 3 жыл бұрын
I've been running the Mossleman thermostat for almost 2 years now...one of the best upgrades for the price you can do.
@BMWDIYGuy 3 жыл бұрын
Totally agree!
@vetodmp2821 2 жыл бұрын
What’s the purpose of this Mossleman and benefits for my engine?
@chriszachmo 2 жыл бұрын
@@vetodmp2821 It keeps your oil temps lower. I average right around 190 degrees F no matter how hard I drive. With the stock oil thermostat, it was around 230 degrees F.
@salimbaksh380 10 ай бұрын
Thank you for your video. With your help and how to install the moussleman thermostat I was able to install mine on my 2018 f80 comp Keep up the great work !
@BMWDIYGuy 10 ай бұрын
Thank you and happy to help!
@atronlol 3 жыл бұрын
Awesome guide! Keep making more M2C content!
@BMWDIYGuy 3 жыл бұрын
Thanks and lots more on the way!
@mobnyc9413 3 жыл бұрын
Thank you for this video🙏🏼
@BMWDIYGuy 3 жыл бұрын
You're so welcome!
@rishabhsharma4079 2 жыл бұрын
Great video, definitely subscribed. If you do this job while doing an oil change, could you eliminate the possibility of spilling the oil?
@BMWDIYGuy 2 жыл бұрын
Not that I have seen at least, just no way around it
@azaniwasaki1 2 жыл бұрын
Firstly, great vid! I assume it's a no (given the very small volume of oil lost) however, do you think topping up oil is essential?
@BMWDIYGuy 2 жыл бұрын
Dead on.. very little oil lost. 8)
@sajadeshahidpour2008 2 жыл бұрын
Greetings from France! Thanks a lot for this crystal clear video. Dumb question : do we need to do any operation before starting the engine again (such as "priming" it or bleeding the coolant) ? Many thanks in advance, S.
@BMWDIYGuy 2 жыл бұрын
Not a dumb question and no, you don't have to take any extra steps like that. Great question!
@sajadeshahidpour2008 2 жыл бұрын
@@BMWDIYGuy Many thanks for your prompt answer !
@xlBattlefieldlx 2 жыл бұрын
What are the torque specs for the bolts?
@BMWDIYGuy 2 жыл бұрын
Front and rear CF strut bar torque values: 28nm Bolt holding oil return pipes: 8nm Oil‐coolant heat exchanger to oil filter housing: 16nm
@xlBattlefieldlx 2 жыл бұрын
@@BMWDIYGuy Thank you! I've been searching all morning for some specs but it's been a cluster.
@BMWDIYGuy 2 жыл бұрын
@@xlBattlefieldlx Happy to help.. finding official torque specs is much harder than it should be.
@Raider1805 Жыл бұрын
What happens if you do spill oil over the belts and surrounding area? Would it cause any damage? Asking cause like an idiot I did spill oil.
@BMWDIYGuy Жыл бұрын
It happens so dont beat yourself up too badly about it. The main thing is to get it clean or best you can.. you could always use a gentle cleaner like diluted simple green, on a rag to help wipe down the belts. Get what you can, and I am sure it will be fine.
@jonnellas7680 2 жыл бұрын
What is the torque specs of the oil thermostat? And the collar too thanks And you mentioned it comes with 2 o-rings after watching this I will order Mosselman and gasket 👍🏼👍🏼
@BMWDIYGuy 2 жыл бұрын
So the 3 bolts are 16nm and the long single bolt holding the collar is 8nm.
@buildindian8169 3 жыл бұрын
I am going to buy this but I’am worried that the thermostat will stick and starve the engine of oil..
@BMWDIYGuy 3 жыл бұрын
Can't say I have ever heard of that happening..
@buildindian8169 3 жыл бұрын
@@BMWDIYGuy ok, I trust your judgment.. Btw, yesterday I found my rear catalytic converter red hot so now I figure will be needing injectors and possibly new cat, might as well buy vrsf down pipes...
@BMWDIYGuy 3 жыл бұрын
@@buildindian8169 Sounds like time for an upgrade! 8)
@Dame102988 3 жыл бұрын
You’ll be fine, I’m in Europe and been running this and their turbos for 2 years. Mosselman are good guys. Been around since like 1979
@anthonyt4981 2 жыл бұрын
would it be a good idea to change the oil while doing this due to loss of oil or does it not matter?
@BMWDIYGuy 2 жыл бұрын
You lose very little so should be ok
@exhaustfanatic2417 2 жыл бұрын
Do you need the install kit gasket and O rings, mine didn’t come with it
@BMWDIYGuy 2 жыл бұрын
In general you want to replace them while you are there.
@exhaustfanatic2417 2 жыл бұрын
Do I need to though? For the mosselman or are they the same gaskets and o rings?
@BMWDIYGuy 2 жыл бұрын
@@exhaustfanatic2417 yes because the gasket goes on the engine side, and on the pipes, that doesnt change. I would change them myself.
FCP Euro
Рет қаралды 5 М.
Kies Motorsports
Рет қаралды 122 М.
Kies Motorsports
Рет қаралды 13 М.
BMW DIY Guy
Рет қаралды 4,1 М.