@Arachnikadia 5 жыл бұрын
Im so happy you showed the front jack point. I didnt want to accidentally jack on the skid plate or hit the oil pan. Its not easily identifiable when you are laying down trying to find it with a lowered car.
@JonAvalon 5 жыл бұрын
Another tip: if you don't have a ultra low profile jack to get it under the front (Especially if you're lowered or have a front lip) and don't have ramps available. You can use your spare tire jack on either side of the front pinch welds to give just enough clearance to slide the jack in. It's not a long term solution but it works if you need it.
@FizuhcuL 5 жыл бұрын
that works or get two nice pieces of wood aswell
@drippingwax 2 жыл бұрын
I bought a nice big Napa jack and then needed to work on my car 5 hours away, so I bought a nice big Harbor Freight jack. The cheaper one jacked higher, so I used it until it stopped going up all of the way, so I started using the more expensive one--except it no longer goes down all of the way. When it doesn't I need to use the HF jack at a pinch weld to get my car high enough to use my Napa jack.
@ballrex664 5 жыл бұрын
I was always looking for where to jack up the car from the front or rear. This videos are truly awesome. Thank you for all your hard work.
@SubiSpeed 5 жыл бұрын
You're welcome! Glad we could help! Thank you for watching!
@dgkparasite1037 5 жыл бұрын
Next two minute tuesday- how to check and top off fluids
@SubiSpeed 5 жыл бұрын
Added to our list!
@timp5883 5 жыл бұрын
Next 2 minute Tuesday...how to properly check your brake pads for wear....great work by the way guys!!
@adamflax4225 4 жыл бұрын
My children thought that they might help Dad fix his car. So, they helped him jack it up. I now have a new Killer B oil pan.
@dirkdarwin2571 4 жыл бұрын
2:25 In the business, we call that a Scotty Kilmer reveal
@Little32king 5 жыл бұрын
Was hoping you guys would cover this is the Two Minute Tuesday series! Keep them coming
@kevingalls 4 жыл бұрын
Thank you for not wasting my time with a 15 min video when 4 mins will do!
@toothpicdinosaur3777 Жыл бұрын
When your pinch welds rust out use the front lower control arm mount shaped like a triangle. In the rear should be 2 90° brackets that are sturdy enough.
@andreipiv 10 ай бұрын
This is great if you can't fit a jack stand and the jack on the same corner due to the jack / stand geometry
@ThePatrickBateman69 5 жыл бұрын
I was also taught to also put the wheel/tire under the vehicle while the car is jacked. You can always replace a wheel but you can never replace a human life.
@SubiSpeed 5 жыл бұрын
As long as that's not the only means of support!
@carbontsx05 5 жыл бұрын
Just use a jack stand
@ThePatrickBateman69 5 жыл бұрын
yup used in conjunction with a jack stand as an insurance policy haha
@drippingwax 2 жыл бұрын
ChrisFix said to keep the jack in place, use stands, and put down a spare tire as insurance. Yesterday my car fell off the stands and I am trying to find a jacking plate.
@ThePatrickBateman69 2 жыл бұрын
@@drippingwax exactly when you have no control of when it can fail, best to use multiple forms of insurance to save yourself
@blazers12369 5 жыл бұрын
bonus tip: look like scotty kilmore
@bloodblitzowns11 2 жыл бұрын
How do people jack up the wrx without ruining your pinch welds?
@davidcharles4636 Жыл бұрын
The ending was hella funny bro! Lmao
@JohnNguyenVincent 5 жыл бұрын
Can you show us how to change fog light bulbs for two minute tuesday?
@SubiSpeed 5 жыл бұрын
You've got it John!
@angreinhan3718 4 жыл бұрын
If i use a jack on the side theres no space to put the jack stand.
@zonefour 5 жыл бұрын
Thank You For This Video.
@SubiSpeed 5 жыл бұрын
You're welcome!
@vincestahl3554 2 жыл бұрын
Super helpful. Well done.
@go4747 5 жыл бұрын
Make a 2mT about how and where to get maps for a Cobb access port and how to install it all.
@SubiSpeed 5 жыл бұрын
Added to the list!
@jesusbarragan7572 4 жыл бұрын
esperres
@philboy521 4 жыл бұрын
It’s safe to use the rear diff for jack point?
@robbiexiong3508 5 жыл бұрын
I found out the hard way too, but thankfully I had the car sitting on jack stands, so i don't notice until I went to go try and take out the stands.
@Apes_love_BMX Жыл бұрын
So if you use the jack point on the pinch weld, where do you put the jack stand? Isn't it suppose to go where the jack point is located?
@waybach 11 ай бұрын
I think the VA’s had more space where you could jack and then place the stands but now that I have a VB, there’s zero space to get the 2 under there and the same time
@xil3ntkha0s 6 ай бұрын
@@waybach that's the issue I had but I moved the jack to where I could fit the jack stand. The jack did come into contact with part of the sideskirt but it felt fine after I completed the job.
@waybach 6 ай бұрын
@@xil3ntkha0s where exactly do you place the jack now?
@xil3ntkha0s 6 ай бұрын
@@waybach just tried to get as little of the side skirt as I could. Jack stand on the right under the section with the two 'cuts'.
@waybach 6 ай бұрын
@@xil3ntkha0s gotcha thanks for that!
@Dirty-D Жыл бұрын
Won’t jacking in the metal pinch weld warp or bent it?Unless you have some pinch weld adaptor.
@zulian420 3 жыл бұрын
Does this apply to the STI as well as far as the jacking point locations?
@sean9267 5 жыл бұрын
So I just jacked up one rear side, placed the stand under the pinch weld and lowered. When the pinch weld met the jack stand, the pinch weld literally folded like a taco.
@jkljkl218 5 жыл бұрын
Wrong spot my guy
@Playin22 5 жыл бұрын
For all of us who track our cars, how to change brake pads and fluids. Possibly even rotors and lines
@SubiSpeed 5 жыл бұрын
Brake pads and fluids are on the list to do! Rotors and lines may take a bit longer than 2 minutes haha
@Playin22 5 жыл бұрын
@subispeed, that's where talking fast and editing comes into play lol, jk. It could be a special 2min Tuesday where it's longer. OR, have it "to be continued" and resume rest of video for Thursday. Good way to keep those views coming 👍
@andreipiv 5 жыл бұрын
Does it matter where the jack makes contact with the rear diff? In the video the edge of the diff is in the middle of the jack pad
@SubiSpeed 5 жыл бұрын
The rear most part of the diff but not the diff cover.
@andreipiv 5 жыл бұрын
@@SubiSpeed thanks!
@pojaypojay4297 5 жыл бұрын
Ive seen other videos where the car was jacked up on the center in between the pinch welds. Do you know the exact location of this?
@SubiSpeed 5 жыл бұрын
We do not, as the jacking locations we covered in this video are the recommended ones from Subaru.
@GriogharThomasBaldwin 2 жыл бұрын
Thannnnnnnk you.
@Joeylikeswakkie 3 жыл бұрын
More importantly which, I’m a little disappointed you didn’t address…what shoes are you wearing? Those look dope!
@SubiSpeed 3 жыл бұрын
New Balance Fresh Foam Cruz 😅
@imkriswithak1135 Жыл бұрын
I always hear horror stories of people jacking up the front and actually putting it on the transmission pan. Any tips to mKe sure its the right spot?
@DTMRM8 5 жыл бұрын
Have you guys been out to a track day since the first time and it broke?
@SubiSpeed 5 жыл бұрын
Unfortunately, with everything going on around here we still haven't had time to look into the issue 😓
@wiiplaya32 4 жыл бұрын
This is going to sounds really stupid, but my struggle is always with if I’m just jacking up one side. How am I supposed to put the jack stand on the pinch weld if that’s where the jack itself is lifting the car from?
@SubiSpeed 4 жыл бұрын
You place the jack just slightly forward or back so there is just enough room.
@wiiplaya32 4 жыл бұрын
SubiSpeed thabks for the quick reply! Just to clarify, it doesn’t risk bending that lip on the frame by not putting it quite on the pinch weld?
@takeda1648 5 жыл бұрын
kev buff af tho lmao
@SubiSpeed 5 жыл бұрын
🤣🤣🤣
@futureboy40 5 жыл бұрын
Hardly 😒
@SubiSpeed 5 жыл бұрын
You must be fun at parties 😂
@lilkingedy Жыл бұрын
Bro I'm not even lowered and I can't get to the front jack point WITH a low profile jack 🤦🏽♂️
@noelsoto4329 5 жыл бұрын
You did it ❤️
@SubiSpeed 5 жыл бұрын
Thanks for the suggestion!
@tomaz2312 3 жыл бұрын
Same for the sti?
@cat740dt 3 жыл бұрын
yes
@FuryJDM 5 жыл бұрын
2min Tuesday: How to Boost restrictor pill once you upgrade turbo inlet hose on STI
@SmileyFace7 3 жыл бұрын
The two minute on the corner disappeared:(
@shadowzone2013 5 жыл бұрын
This isn't really related to the video but is there a website like subispeed but for the MX-5?
@SubiSpeed 5 жыл бұрын
Not that we know of, sorry :(
@JeffreyWalder 5 жыл бұрын
You didn't say what size jack to use... 1600kg 1800kg 2000kg Thanks
@Steve-qr2lm 4 жыл бұрын
Doesn't the metal jack stands damage the seam weld area?
@SubiSpeed 4 жыл бұрын
Not if you carefully lower the car onto them. Just don't drop them on there carelessly.
@jaimecarrasco515 5 жыл бұрын
Gd video
@troybizzle 5 жыл бұрын
How do we jack up the rear if we have a diffuser?
@calvindiv7231 5 жыл бұрын
this is perfect.
@madduck692002 5 жыл бұрын
You forgot us guys with a lift like your's?!?
@SubiSpeed 5 жыл бұрын
You guys know better!
@millhouse313 2 жыл бұрын
Really? The rear diff is a good place to jack the car up? That’s scary. Is that the standard place people use to jack up the rear end?
@Mattle_lutra 4 жыл бұрын
I cringed when I saw that jack hit the rear diff. I always jack further in on the diff, avoiding the cover to not break/damage the seal. Am I just paranoid?
@Kradle 3 жыл бұрын
Maybe. I think it might be good to keep in mind but I've done it like him twice now and I don't think it's damaged anything (so far.)
@danhectic5629 13 күн бұрын
yeesh old post but yea i was wondering the same thing. so in front of the flange where the cover is bolted on would be safe?
@ROSQUILLA02 5 жыл бұрын
next two min Tuesday how to properly rotate your tire.
@SubiSpeed 5 жыл бұрын
Will add it to the list!
@johnanderson3746 4 жыл бұрын
lift emergency break
@alamsas2 3 жыл бұрын
I've used a jack and jack stands on my car and it's been slowly bending the pinch welds open.. is there a better spot (preferably flat) to use the jack on?
@NathanaelGreer 3 жыл бұрын
You can use a “pinch weld jack attachment “ to avoid this kinda stuff. Lots of companies make and sell them for under $20
@waybach 11 ай бұрын
Or use a microfiber towel under
@mrexile09 5 жыл бұрын
Wish they showed this for the sti
@AlboAl8 5 жыл бұрын
2mt how to change your brake pads!
@ROSQUILLA02 5 жыл бұрын
that's not a 2 min job bro
@SubiSpeed 5 жыл бұрын
Maybe we'll give it a go! Two Minute Tuesday - Fastest Brake Change Ever!
@AlboAl8 5 жыл бұрын
@@ROSQUILLA02 my bad, thought it was about explaining how to do something on your car in 2 min.
@ROSQUILLA02 5 жыл бұрын
Oooh. No wories bro.
@DozaO23 3 жыл бұрын
Lol didn’t learn anything
@Since-1883 5 жыл бұрын
Bro why are your arms so skinny if you’re working out all the time?! 🤔
@guest2007 4 жыл бұрын
27 sep 2019 4:43 pm edt: bicep-curl make strong-arm, but during using arm for doing gentle-task like scraping eye-booger/dried-eye-mucus, nose-booger/dried-nose-mucus, arm-strength-control may be reduced then accidentally wounding eye-lid, nose-interior
Way of the Wrench
Рет қаралды 528 М.
奧特羅羅 Ultraman
Рет қаралды 6 МЛН
Import Image Racing
Рет қаралды 13 М.
Backyard Chevy
Рет қаралды 206 М.
Scoobyfreak86
Рет қаралды 23 М.