THIS IS THE VIDEO I NEEDED!!!!!!!

How do you bend pvc roller coaster track

God you are awesome. Not only did i NOT fall asleep, I actually learned from this. Really cool

Hi Will, Thanks for the call out for PVC Bendit.

Great video! This method definitely beats the ol' sanded down 1" coupling or 1.25" pvc joints.

You answered my question from the other video. Nice job and invention.

How to you build the lift hill system? Could you do that next?

I'm planning making my own rollercoaster. How do i bent the pvc and make a smooth turn

Thank you so much for making this video!! Very helpful!

how to bend the pvc to bank?

Now he needs to teach us how to bend track pls

Yes

How do make a curved pi cue of track?

Tip: Use PVC primer on both pieces before applying the PVC cement/glue.

I was wondering how you make a cart for the track

How do you bend it to the right angles?

Could you do a video for making turns, banks and inclines/declines where the track goes from straight to one of these variants

Oh, and a heat gun with a variable temp setting is cheap, and works great to get PVC pliable, and would probably keep your wife off your back about using her appliances lol All joking aside, however, are there any toxic fumes given off by PVC, CPVC or any of the other piping we often heat up? I have found sometimes I can notice faint odors, even when not setting it on fire. I have gotten into the habit of wearing a respirator face mask, cause who knows what's in those fumes!

I think you can use a wood dowel also.

WOW! You deserve more subscribers! Can you do a tutorial on how to make a coaster cart though?

This has been a PSA on PVC from CDP.

How do you bend the pvc to make a drop

If you don’t now how to bend pvc u put sand where you want it to bend and the use a heat gun to make it soft Then u can angle ITV the way u want

How do you make curved track?

Wow, I was always under the impression you used wood doweling to make the connections?

How do u build curved track

Would it be a stronger join between rail and cross-tie if the screw was screwed flush against the inner wall of the pipe instead of to the outer edge of the pipe? Does the weight of the wheel rolling over the track not eventually cause the exposed screw inside the pipe to bend? I can’t tell without having it in my hands!

Thank you, I am looking to make a jet ski land launch, and am planning to use PVC for the rails to the water. I am thinking I may also install concrete and rebar inside each section, as it will be carrying a lot of weight @ ~800 lbs. and I want the rail system itsel to be extremely sturdy, as it will be subject to occasional high surf and hurricane force winds. My plan is to keep the height of the ski 'locker box', aligned with the height of my trailer. In the event I need to offload the ski from the rails, I can winch it forward, right on to the trailer. I plan to use a ATV winch to pull the ski back out of the water up the rails. It's a good rise from ther water line up into my yard, ~4, and adding the trailer height, another foot for five total. To minimize scratches to the jet ski underside, I am thinking I might be able to build a cradle for the ski to sit in. It slides on the rails, rather than the ski. I am thinking PVC there as well, but again, wondering about the crush rating on 3" pipe. Does anyone know how much inward force it takes to crush say schedule 40? I am thinking a jet ski would be no problem. they rate it for PSI burst pressure, can that be equated to reverse inward pressure? E.g. if it is 2200psi, does that mean it can withstand 2200 lbs of weight on the exterior, before crushing?

What type of PVC should I use for a coaster, I was thinking of using 2" Sch. 40 PVC but I was wondering if I should use Sch. 80 instead because I want to have a max weight of 150 pound riders and G-Forces that max out around 3Gs. Also there will be ties around every 1 foot but in high G-force areas there will be more.

I've had trouble keeping the PVC hot it cools down too fast to form it properly

How to turn a track

You should make a super steep rollercoaster with crazy turns

Can u show us what motor you use for the lift hill and what chain type I’m building a coaster with a 90 degree climb and the only thing I’m having trouble with is what motor to use

how do you curve track?

How does the roller coast bend and turn if wood can’t bend

Are there any easier ways using less materials, I’m trying to save costs wherever possible with our coaster, but with as much safty as possible

How can you make the track so that it can stay connected but still go at a angle?

What’s the best paint to use?

Ouuu I’m first yay😂 but this rly helps

How to make a lift hill

Where did you get the coaster periodic table?

Hi

Hello i'm french, and bad in English. I don't know what is the type of your pvc pipe : " Pvc pipe " for poo and pee drain ? "Pvc pipe " for electric ? "pvc pipe " for pneumatic ? internal diameter outside diameter UV resistance or other skill ? ...=) thank

This is to hard I can’t do it

It's pointless to use the glue without primer. The primer actually allows the pvc to soften and become porous so that the glue can bind the two pieces.