How to (KILL Rust) Fast & PERMANENTLY On Classic Cars & Trucks (Top Secret Sauce)

Рет қаралды 109,941

Күн бұрын

In this video I share with you a top-secret sauce that one of you guys told me about!!! This stuff really works and KILLS Rust fast and permanently , so you have no recurring problems in the future. I will link all products used in this video below in this description below. All links are from my amazon affiliate account that I make a small percentage off of qualified purchases at no additional cost to you. Thank you guys for watching I hope this helps with your restoration.
Paint Shaker 4000 Video Link • Build your own FREE (S...
Make your own patch pannel 65 C/10 • Beginner (Rust Repair)...
How to Strip Rust Video Link • How to Remove Surface ...
How to Test Weld Video (ETCH WELD) • (How Strong Are Your W...
My website for t-shirts: www.acdesignsgarage.com
My PO Box: PO Box 782 Troutman NC 28166
PRODUCT Links Below
Skyline Ospho (Rust Killa) amzn.to/4alToE1
Spray Bottle amzn.to/4auUjSY
120 grit Sand paper roll amzn.to/43QnpcJ
Rust-oleum Primer amzn.to/43NiRDW
Red Scotch Brite amzn.to/4aGRdeb
Sprayway Glass Cleaner kit amzn.to/4aMaWt1
Paint Stripper Disc amzn.to/3v7Ukfs
40 Grit flapper wheel amzn.to/3v9EIYT
Dewalt grinder amzn.to/3RKswXF
Bench Mark Grind shield amzn.to/3GMwOHM
C clamp amzn.to/4akJUtb
Defiant Gloves amzn.to/47YYMvQ
IR Grinder amzn.to/3NMyUep
3m ROLOC Grinding disc amzn.to/48yKZMq
D.A Sander amzn.to/4ajcgmV
80 grit 3m da sand paper amzn.to/4che5Cq
3m Mask amzn.to/4a0zrmk

Пікірлер: 91

@chops6474 4 ай бұрын

Ospho is good stuff, been using it for years. But it has limitations. On heavy rust, you have to apply it multiple times as the acid doesn’t reach below the absolute top layer. You can experiment on a heavy rusted metal. Come back the next day and scratch across the metal, the rust will still be underneath. The box store stuff works ok but it is a little weaker than Ospho. I always neutralize with water before primer.

@ACDesignsGarage 4 ай бұрын

Yeah I noticed that when I applied it on that camaro frame and it needed more. I think id you wire wheel it or DA sand with 80 grit then apply it works better! Thanks for the info!!!!!

@ericcrawford326 4 ай бұрын

I looked up the MSDS . It is phosphoric acid and chromium. The phosphoric acid is what converts the rust. The chromium becomes chromium phosphate. Which protects the metal and is used for paint prep. In my opinion this should work better than what I’ve been using ( concrete prep) , it’s phosphoric acid and alcohol.

@ACDesignsGarage 4 ай бұрын

Thanks for the tips!!!!

@davidanderson2393 4 ай бұрын

Ospho works great on the outdoor equipment when preparing for paint, I haven't tried it on fenders yet, but I have used it on floor pans.

@ACDesignsGarage 4 ай бұрын

I need to try it on my car trailer!!

@pedroalejandro8324 4 ай бұрын

I love all these videos but I only dislike when u guys start talking n talk more than is showed, show n tell more action less talk, sorry but I'm just being honest.

@theaussienurseflipper.8113 2 ай бұрын

Fark he going on and on

@SS-iv7wv 3 ай бұрын

Not trying to be mean but people don't have time to listen to jibber jabber for minutes on end about how your gonna kill this rust. Get on with what you want to do. Here's the job, here's the product, here's how you do it. Simple, but thanks for tryin.

@danielalamo2075 2 ай бұрын

That stuff is great! I used it a couple years ago on the drip rail of my dads 1963 GMC.

@ACDesignsGarage 2 ай бұрын

Yes it is ,thanks for watching!!!!

@BustedKnucklesBuildsTexas 27 күн бұрын

Great video , going to try it on my rusty 63 bel air

@ACDesignsGarage 25 күн бұрын

It works pretty good!!!

@SpankysHotRodsandCustoms 4 ай бұрын

I’ve got a project I need to try this on. Thanks for sharing brother

@ACDesignsGarage 4 ай бұрын

Thanks brotha, they say it can react with certin primers but the rattle can was fine, but I cleaned the residue off with lacquer thinner and danded it clean so I wouldnt have trouble lol!!

@Big88Country 3 ай бұрын

AWESOME!! I'm from Hickory and live in Sneads Ferry now. NEW SUB!! Getting ready to start work on a 72 Grand Prix that I have to replace the roof panel. The vinyl top hid rust for a long, long time and now we got big holes. I might resort to cut and butt welding depending on how bad it is in places. Replacing the whole roof panel has got me a little nervous if I'm being honest. Good channel, can't believe I haven't come across it before now. Gonna get me some of that Rust Killa!!

@ACDesignsGarage 3 ай бұрын

Hey man Thanks!!!! Replacing a whole roof is not as bad as you think if you can get a new one!!! Ill drop a link to a 68 camaro we tore down to the vin number lol kzfaq.info/get/bejne/i5iPfZycq52-lqc.htmlsi=piJH4O0ql0rqUbKx

@xxkingslayemxxgamer5553 4 ай бұрын

Been using that stuff for 30 years work's great

@ACDesignsGarage 4 ай бұрын

Glad I found it its amazing!!!!

@TreDeuce-qw3kv 2 ай бұрын

i have used Vinegar for surface and muriatic acid for heavy rusr for years with great effect.

@ACDesignsGarage 2 ай бұрын

Yeah that work great also

@user-ij5ck9yg1b 2 ай бұрын

Got motion sickness trying to watch.

@gratefullee1042 4 ай бұрын

Something about a T-shirt daka derr datook da derr do damn dur 😅

@duMaurierMalone 3 ай бұрын

Watched and enjoyed the knowledge you’re dropping!!! Please provide details of purchasing a rattle can shaker

@ACDesignsGarage 3 ай бұрын

Im fixing to make some more, if you want go to www.acdesignsgarage.com and subscribe to the email and ill let you know when there done!!!!

@rickyhildebrand114 2 ай бұрын

Take the phosphoric acid one step further by applying some sort of plastic over the ragss to keep it from evaporating.

@ACDesignsGarage 2 ай бұрын

Thanks for the tip, we use to do paint stripper like that!!!

@mikecunningham7621 3 ай бұрын

53 minute video for about 2 minutes worth of information. Yak, Yak, Yak.. I'll save you the time.. get some Ospho.

@kencoulter7978 4 ай бұрын

Have you tried Klean Strip Metal Prep? It's sold in the big box stores for around $20 gal., works the same from what I can tell.

@ACDesignsGarage 4 ай бұрын

No I haven't thanks for the tip!!!!

@BlueMacGyver 4 ай бұрын

I used it, works great. You need to remove a lot before using though. You cant just shoot the metal prep on there. I wire wheel the majority off or us a 36 grit flap on the grinder, then when it is mostly gone it spray it and scrub with a green pad until it looks good, when the deep down micro shit turns black you know you are good to rinse with fresh water for 5 min and then I finish it up with a towel and a hair dryer or flame.

@UnconventionalMetal 4 ай бұрын

Concrete Prep & Etch at Home Depot. I use it all the time, works great. Some others have a higher concentration of phosphoric acid from what I hear though.

@santoscamacho3361 4 ай бұрын

Yup and it's cheaper ..I pay less than 20 a gallon ..unless it went up already

@moxie1970 4 ай бұрын

@@UnconventionalMetal I use muriatic acid, brush it on let sit wash off and primer.

@markt9438 3 ай бұрын

The reason why you would use metal prep instead of that green stuff is could you go over it with a Scotch-Brite and it gets the job done much faster!

@ACDesignsGarage 3 ай бұрын

Ok thanks!!!

@JamesSmith-hx3lp 4 ай бұрын

Great video, I’ve used osmos before good stuff, looking forward for more videos. Better put a Patton on the paint shaker!😂

@ACDesignsGarage 4 ай бұрын

Hahaha I though about it ,thanks for watching!!!

@wesleysmith995 4 ай бұрын

Make sure you at the Goodguy car show in Raleigh North Carolina this year.

@ACDesignsGarage 4 ай бұрын

I need to go there sometime!!!

@jrperki1 Ай бұрын

That is 45% phosphoric acid. Kleen Strip concrete prep is about 40% and is 50% cheaper.

@ACDesignsGarage Ай бұрын

Thanks for the tips!!!

@Beek88 4 ай бұрын

He is going to have a rough bit. Keyster bunny incoming!

@rickyhildebrand114 2 ай бұрын

Of you have some bright trim that has dulled up.take the acid to eat off the zinc plating,then polish the hard aluminum to a bright shiny finish....your wecome...lol.Is that rust o slum gonna be compatible with other paints ?

@ACDesignsGarage 2 ай бұрын

Hahaha its the only brand that I've not had a ton of trouble out of. I use to love krylon but it's bit me before!! I've 2k cleared over rustoleum with sucess!!

@CKILBY-zu7fq 3 ай бұрын

Looks like it works. 🤔👍

@ACDesignsGarage 3 ай бұрын

Works great!!!!

@randywiddis 4 ай бұрын

You may want to experiment with different primers over Ospho. Certain primers dont adhere well to it.

@ACDesignsGarage 4 ай бұрын

I read that on the bottle, thats why I pretty much sanded it off.Also I washed it down pretty good. I think I put that in the video but I cant remember lol thanks for the tips!!!! The rustoleum see to hold on pretty good

@wildbluewilly1949 4 ай бұрын

@@ACDesignsGarage Just used this on my CJ3a frame after grinding off the rust to bare metal…. I decided to pressure wash it afterwards and scrub it with a red scotchbrite before putting on my primer coat. No issues of adhering 👍

@doglegjake6788 4 ай бұрын

Thanks for sharing a great video

@ACDesignsGarage 4 ай бұрын

Thank you for watching

@mrtaktiks 3 ай бұрын

Have a 1984 Porsche 911 on a lift in a heavy mil portable garage. But the leak and humid is present. So…undercarriage surface rust. Is your solution a good option for this? Will it turn Porche’s yellow chromate screws,bolts,fittings, etc dark or black? It would look like an undercoat, I suppose. (In Chicago).

@ACDesignsGarage 2 ай бұрын

It may be a good fit, not sure about the chromate, if you had a spare one I'd try it first if you Wan to keep that look!!!

@davidwellman7080 4 ай бұрын

I have a 73 C-10 that I've been working on. It's rusty I may try that stuff for that. I'm in Rutherford county in North Carolina. What part of North Carolina are you in?

@ACDesignsGarage 4 ай бұрын

Thanks for watching, Im in Iredell county

@shermy584 4 ай бұрын

Not far from me in Burke cty

@davidwellman7080 4 ай бұрын

@shermy584 I was born in Burke county., my family is close to Casar. Close to Dirty ankle if you are familiar from that or not.

@shermy584 4 ай бұрын

Not to familiar we moved here in 2021 to get our freedoms back 😁😁🇺🇸

@dewholdingsllc1050 3 ай бұрын

I routinely use klean strip metal prep. Looks the same. What is the difference between them? Its less than $18 /gallon at HD

@ACDesignsGarage 3 ай бұрын

Not sure I'd love to try it!!!

@speedfreak8200 4 ай бұрын

What ever happened to Boomhauer ?

@timhudson8958 3 ай бұрын

Looks like ospho!

@ACDesignsGarage 3 ай бұрын

It is, I love this stuff!!!

@Thedropshopkustoms 4 ай бұрын

What part of the tarheal state You in? I’m from Hyde County originally I now live in Long Beach Mississippi until I retire in 2 years…

@ACDesignsGarage 4 ай бұрын

Just north of Charlotte, Hyde County looks beautiful!!!

@Thedropshopkustoms 4 ай бұрын

@@ACDesignsGarage it’s a giant swamp with bird sized mosquitoes lol it’s beautiful country close to being heaven with hardly any crime! Unlike here in south Mississippi with New Orleans crime….

@kenstone6686 3 ай бұрын

Hey I’m in troutman nc where are you

@ACDesignsGarage 21 күн бұрын

Mooresville

@steveozbourne24 4 ай бұрын

Im newton your channe would you make meca painf can shaker for my saw csaw o ok esse?

@ACDesignsGarage 3 ай бұрын

They work great, im gonna start making them soon, ill make an announcement on a video before long!!!

@invisableobserver 3 ай бұрын

Is that your light blue & white C10?

@ACDesignsGarage 3 ай бұрын

Yes, I need to get back on it!!!

@invisableobserver 3 ай бұрын

@@ACDesignsGarage I have a 65 light blue & white C10. What state are you in?

@johnlewis6928 3 ай бұрын

You talk to mych

@joshnobles3210 3 ай бұрын

Perhaps he talks more than some like lol I guess there’s is a mute button but really he just telling his thinking and game plan like we all do when we do things and how that plan is working or most likely what’s not working so maybe others can change their plan before they start. More he experiments less we have to.

@IFORBIDANYDATACOLLECTIONTOALL 3 ай бұрын

You had my sub at Jesus loves you

@ACDesignsGarage 3 ай бұрын

Thank you hope you have a Blessed day!!!!

@evangelist6277 3 ай бұрын

Cannot understand a word your saying, do you have it in English?

@theaussienurseflipper.8113 2 ай бұрын

Over 10 mins flapping his gums and still hasn't gave us the recipe

@steve-rr3nq 2 ай бұрын

you are making me sea sick. stop swaying all over the place.

@zekerivers5189 3 ай бұрын

Buy a new Fender not worth the time and effort

@ACDesignsGarage 3 ай бұрын

Thats a good option!!!

@garyloflin3215 3 ай бұрын

Way to much talking 😭

@zekerivers5189 3 ай бұрын

Yeah there's a lot of options however you did you and very nice job repairing it have fixed money myself is there a prone to rust Rustoleum is a very good product personally would have used a metal etching primer for direct to metal but each his own