Here is the second part in the series of videos I'm making that goes over the process of making a concrete garden statue.
Пікірлер: 31
@donnabirnbaum65802 жыл бұрын
Was looking for a tutorial on making a mold for cement project Watched about 30 of them YOU WERE THE BEST!!!! Thank you so much!!!
@calilovebug38977 күн бұрын
Great video!
@tpifj4022 күн бұрын
Great video, best one I’ve seen on KZfaq
@tobe414114 күн бұрын
Excellent. Thank You. I can do this now
@luism.raposo5138 Жыл бұрын
This is my first time watching your video. I really enjoyed it. You did a beautiful job and explained it very well too. Good video to learn folks. 💕
@ebmartin1379 Жыл бұрын
Right on …. Thank you so much for teaching us out here ❤️
@user-vm9vf9cu6g8 ай бұрын
GREAT EXPLANATION ! THANKS FOR SHARING !
@roseontiveros24014 ай бұрын
Wow, you are really good at doing these. It's just so exciting for me to watch you do this. I would like to make cactus molds, would that be possible? Please advise Thank you
@user-dh3bh9pk2n4 ай бұрын
🙏
@outside45314 жыл бұрын
Excellent video. So informative!!
@christalmotter29554 жыл бұрын
thanks :)
@carterharrington Жыл бұрын
Thanks so much sharing !! Great video
@normasuelimonteirodesouza2462 ай бұрын
Aula espetacular! Muito grata!
@mahmoudzaefi2958 Жыл бұрын
can we use polyester resin for casting with this mold? and before casting do you use PVA for mold release? or can we use ( mixing of castol oil with rubbing alcohol?) thanks.
@schoolstudio7915 Жыл бұрын
Thank you.
@michaelpearson12724 ай бұрын
Don't worry about latex build up on your brush. Steep your brush over night in white spirit and it will eat even hardened latex of but make sure you give your brush a realy good wash in dish soap water to get all that spirit of before using that brush again.
@sturfam8 күн бұрын
do you use some sort of a release between the resin and latex ?
@alanabroad34717 күн бұрын
Can you just dip the statue into the latex?
@mensahnii20812 жыл бұрын
Thanks
@kimdavis6798 Жыл бұрын
I really enjoyed the video thank you I learned a lot. I have tried to sculpture just small stuff like a little cat out of air dry clay. I just don’t have much luck is there an easier material or substance to sculpture out of
@michaelpearson12724 ай бұрын
Never use direct heat to speed dry your mould making as it can de laminate each layer you paint on. Patients is the key. Let each coat semi dry before adding the next coat.
@mahmoudzaefi2958 Жыл бұрын
How long do you usually wait for the PVA to dry?
@ismaelrodriguez9777 Жыл бұрын
Nesesito el latex donde lo puedo comprar
@cmajors459611 ай бұрын
Where can I purchase Laguna Latex?
@PenniieXiongs9 ай бұрын
Where to buy?
@williamdowns2244Ай бұрын
Can i put latex on a concrete statue to make a mold?
@williamdowns2244Ай бұрын
Does she ever reply to anybody
@marywebb11388 ай бұрын
Why do you think that you need the irritating background music? Didn't finish watching. Too bad because it was probably a good v
@MG637 ай бұрын
So that irritating people like you can make irritating comments about the irritating videos that keeps you irritated. Your welcome. Regards. Mr Irritator.
@cliffdariff74Ай бұрын
Yup.... the music just played and played and played and played and played.......