how to make a music rhythm led flashlight circuit

Рет қаралды 255,760

6 жыл бұрын

In This Video we are going to show you how to make a music rhythm circuit.
The components used are:-
* Breadboard - x 1
* Electret Microphone - x 1
* Transistor - (BC547) x 9 NPN TYPE
* Resistor - (1M) x 1
(10k) x 2
(22Ω) x 8
* LED (Light Emitting Diode) - (Any Colours) x 8
* Ceramic Disc Capacitor - (100nF) x 1
* DC Switch - x 1
* Battery - (9v) (with battery clipper) x 1
* Connecting Wires
If You have any queries related to the video feel free to comment in the comment section
Also Make Sure To Watch Our Other Videos
1) How To Make A Digital Dice:- • How to make an electro...
2)How To Make A Mobile Detector circuit:- • How To Make A Mobile P...
3)How To Make Wireless Electricity Transmission Circuit:- • Wireless Power Transmi...
4)Arduino Basic Projects:- • Arduino Blinking of an...
Make Sure to Subscribe to our channel !!!!!!!!!!

Пікірлер: 501

@terryfisher8872 6 жыл бұрын

I just finished assembly of the breadboard LED circuit. I followed the steps carefully, but nothing happened. THEN I rechecked your video and realized I had not connected all 8 transistor bases to the main base of BC547. The thing lit right up on power up after that. Now, I am going to transfer this whole project over to a PC board and make it permanent so I may use it for my music show! Thanks for a great design and idea. By the way, I had no 100nano F cap so I used an 82nano F, and had no 22ohm resistors, so I substituted them for 100ohm. Still works without a hitch.

@MAKs_electech 6 жыл бұрын

Well thanks for your interest in my videos.

@zeenzeen5394 5 жыл бұрын

We cn use one rgb led strip and it is amazing..only one transistor is needed

@Custom3dPrinting4U 4 жыл бұрын

I bought the transistors and own resistors and wired it to a board and followed ever step and nothing lights up unless I take the mic out and replace with wires (short the mic)

@harshadgunjikar1595 3 жыл бұрын

@@zeenzeen5394 can you tell me the rgb strip connection

@rishihinge569 2 жыл бұрын

How many volt capacitor are used

@macepriestley9403 2 жыл бұрын

YOU MY MAN, ARE A GIFT!! A special thanks to you removing background music while you insruct. Others CRANK music that we all may not want. That becomes distracting.👍🙏

@terryfisher8872 6 жыл бұрын

I think this is great. As a musician, I am going to use this idea to light up my solo show with my singing and guitar. My show depends on traveling lite and compact. Perfect to add for excitement. I will let you know when I finish the breadboard how it goes, then I will transfer that to a permanent board!

@thaynecearrachkerr8497 5 жыл бұрын

Where can I buy tickets to your music show?

@MAKs_electech 5 жыл бұрын

😂😂😂 at my place may be😁

@marcelomaxton4213 3 жыл бұрын

a tip : watch movies on Kaldrostream. Been using them for watching all kinds of movies during the lockdown.

@juancorey4138 3 жыл бұрын

@Marcelo Maxton Yup, I have been using kaldrostream for months myself :)

@rishihinge569 2 жыл бұрын

How many volt capacitor are used

@Marisol1711 5 жыл бұрын

Hi! By my understanding the 1M resistor is used along the capacitor to form a high pass filter, however, if I design to have a cut-off frecuency of 20Hz, this resistor is 80K. Do you think it would mess up the whole thing if a switch the 1M resistor with a 80K one?

@dymjgaming8546 8 ай бұрын

Thanks bro I saw each every video on yt to make it glow on beats but every time it didn't worked until I saw your video thanks bro for helping me ❤❤❤❤

@charann8583 5 жыл бұрын

Super thanks I tried and it's working once again thanks bro

@MAKs_electech 5 жыл бұрын

Your welcome bro

@Allahumdulillah-m9f 2 ай бұрын

I done ✅ my project and it's working . Thanx

@ninjastorm9669 4 жыл бұрын

I am student of mechatronics and I want electronic project for weekend I think this is best and simple

@amitsahu1980 6 жыл бұрын

Thanx....Maine ye project kl banaya aur isne ache se work bhi Kiya......thank you Agar aap ardino se kuch project banaye toh bohot accha hoga hamre liye

@MAKs_electech 6 жыл бұрын

Okkh hum karenge PR app like aur subscribe karna na bhule. Thanks 😊

@ghulamfatima7068 5 жыл бұрын

Resistors 22ohm ki jaga Kounsa laga sakte hain

@007Rickie 6 жыл бұрын

thank you i was looking for a video like this for a long time i wanted to put light in my car base box

@MAKs_electech 6 жыл бұрын

Welcome 007Rickie

@thantzinphyoe5568 2 жыл бұрын

I got the right hardware circuit. Your vdo helped me so much. Thanks a million Sir.

@jane3598777 5 жыл бұрын

this is co cool ! can anyone tell me how it work? please !!i need the detail for this project.thank you!!

@ajjazshaikh9247 4 жыл бұрын

Thanks a trillion for this wonderful project idea👍👌 I did it for my college project n my sir loved it .......in end it dint worked according to the music what may be the reason ? Microphone issue ?

@arvindbhutale201 4 жыл бұрын

Help me out dude it isnt working

@carlosvalentin9670 3 жыл бұрын

Dude, you helped me soooo much. It worked excellent! The only thing i couldnt get was the 100nF capacitor but i used a similar one and it worked just fine. And i used 2N4001 Transistors, if youre using a different Transistor make sure you know the pin configuration cause some of them are different, the first time i couldnt get the circuit done because i didnt check that.

@SAAD-nh1oe 9 ай бұрын

Similar capacitor value please

@shresthgaming9318 9 ай бұрын

what does pin configuration means?

@carlosvalentin9670 9 ай бұрын

@@SAAD-nh1oe I used a 47nF capacitor, they are orange and have a 473 in the middle.

@carlosvalentin9670 9 ай бұрын

@@shresthgaming9318 It's the emitter, collector and base of a transistor, simply google the number of the transistor you have + pin configuration. You might have to switch some connections depending on what kind of transistor you bought.

@shresthgaming9318 9 ай бұрын

@@carlosvalentin9670 i have BC574 as mentioned in video..will it work?

@xzentv1268 5 жыл бұрын

I have connected all just like from the video but when i put the 9v battery it just light up and it didn't stop or even beat with the sound its just a steady light like a basic led circuit

@kshitijsahu2149 5 жыл бұрын

Bro, it's lit.....literally🔥🔥🔥

@razerstar9581 4 жыл бұрын

Very Well Explained and in a simple and Creative manner.!! Looking forward for more such Content 💯

@husvsisvivsig3944 3 жыл бұрын

How to short the bases of the transistors

@deepakchaurasiya3080 2 жыл бұрын

Bhaiya na is a great place to work for men adi and voltmeter in the same way as the most wellcome of the day

@bierzoelite8875 5 жыл бұрын

Very nice video . Thanks to you I undurstand a lot more of what is needed for my project . 40 leds red green ( christmas 😄) But i wonder can I use same transistors and capacitator with 5 volts input ??

@utsavkoppad6423 Жыл бұрын

tq bro for your great hard work we to used ur project to pass and it was good !!!!!!!!...

@rajupandey8407 6 жыл бұрын

That's something to try at home man, superb video and it works totally correct. Keep uploading

@MAKs_electech 6 жыл бұрын

+RAJU PANDEY ty brother

@miguel7152 Жыл бұрын

thank you soo much, from cd. juarez México!

@riyaz8_0_3 5 жыл бұрын

Thank u boss my project is working👌👌🔥🔥👌👌👌😎🎊🎊🎉🎉🎉🎉

@informativevideos3825 5 жыл бұрын

But Mera work ni kr rha

@danyalkanzanahmadahmad4808 5 жыл бұрын

how bro

@MAKs_electech 5 жыл бұрын

Please make sure that all connections are proper. Follow all the steps properly definitely it will work..

@varsha.m7053 Жыл бұрын

Really ur project is working?? Can you please help me as soon as i give the power supply leds are blinking without giving sound? Wt is the reason

@riyaz8_0_3 Жыл бұрын

@@varsha.m7053 please check the transistor connections but please check all the connections are connected perfectly as said in video i did exactly same as in video it worked perfectly for me before 4 years ago all the best for you!! It will definitely work I assure if you follow the video exactly

@abhishekdesai3418 6 жыл бұрын

Superb video. Keep it up

@MAKs_electech 6 жыл бұрын

+Abhishek Desai thanks. We will

@amirabahaa7593 4 жыл бұрын

please help!!!!! it doesn't work on the normal sounds or at least the mobile sounds it needs loud speaker how can i fix it to be flixable with also the normal sounds ? i've just working on the project of my college .

@user-kx2tf4vd2i 3 ай бұрын

I have question about this my led lights working directly could you plzz help me out

@Talshiinomoto 4 жыл бұрын

Thank you, now my project is done, kudos to you man!

@husvsisvivsig3944 3 жыл бұрын

How to short the bases of the transistors

@rishihinge569 2 жыл бұрын

How many volt capacitor are used

@prabhag1967 5 жыл бұрын

Super... This my small project.. I choose it.... Very super project

@sailalitha1722 5 жыл бұрын

Oo wow amazing loved it... I'm working on a mini project plss suggest me a innovative simple mini project plss

@MAKs_electech 5 жыл бұрын

Mobile Detector Circuit, Led Chaser Circuit, Digital Dice...

@Renu92 4 ай бұрын

Actually in this video u used a 2pin mic but I have 3 pin microphone is it useful to make that circuit sir

@HussainAli-il8bf 2 жыл бұрын

PLEASE GUIDE ABOUT ROLE OF EACH COMPONENT PLAYING IN THIS CIRCUIT AS I NEED IT FOR MY PROJECT

@monu_alhan 5 жыл бұрын

It's awesome 👌👌👌👌👌

@shruthik5865 5 жыл бұрын

what is the application for this project pls tell me bro

@anujjaiswal4358 6 жыл бұрын

Its Really Good

@MAKs_electech 6 жыл бұрын

+Anuj Jaiswal thank you !!!!

@ClaudeTube 6 жыл бұрын

Interesant montaj cu leduri. 473.

@mihneavolosciuc4001 4 жыл бұрын

I love you I love you I stayed two hours but it was worth it💕💕💕🍻

@sucharithabangarugari9643 5 жыл бұрын

It's ok... I had done my project I got an output.. Thank you

@MAKs_electech 5 жыл бұрын

Well that's superb

@Sera79 3 жыл бұрын

Thank you - this is So cool! 😎 will need to make this

@omkardhatingan2873 6 жыл бұрын

Its a nice video

@MAKs_electech 6 жыл бұрын

Thanks😊

@vyankateshyeshal907 6 жыл бұрын

Nice

@mrbk1120 5 ай бұрын

Any sounds it will blink right

@brucerulz5297 6 жыл бұрын

nice job. just built the circuit. What would I do to adjust sensitivity? Maybe a pot somewhere?

@MAKs_electech 6 жыл бұрын

Yeah, u can adjust the sensitivity by adding a pot after the mic. But it would slightly change the sensitivity not by a great margin

@Custom3dPrinting4U 4 жыл бұрын

How did you get it to work?? My circuit hardly lights up when i bypass the microphone

@Mohamed-dv5zm 6 жыл бұрын

what should i change to use a 12 volt leds at each transistor ??

@MalikNomanYouTube Жыл бұрын

Music Name please??

@markceasarenriquez1988 Жыл бұрын

May I ask? We have the same components, but why does mine not fully off when the music is playing?

@markceasarenriquez1988 Жыл бұрын

Only the intensity of the light flicker

@myatsu3985 4 жыл бұрын

Out of 8 LEDs only 3 are working properly with music rhythm. I've also checked the connection from the transistor but the fourth LED and other LEDs are not still working. How can I solve this? I'm doing this for my school project. please reply sir.

@MAKs_electech 4 жыл бұрын

If the 1st three LEDs are working properly then there might be a problem in the 4 transistor it might be not working properly. So i would suggest you to please change the 4 transistor and try once....

@sarimansari9701 3 жыл бұрын

It didn't work for me ! 😐 I did it with one LED... I connected it's anode to +rail and cathode to collector of 1st Transistor... Then I put the main Transistor on BB and connected it's collector to the base of 1st Transistor... And connected emitter of 1st Transistor to the ground with 22ohm resistor... Then a 10kohm to the collector of main Transistor and other side to the +rail Then a 1Mohm to the base of main Transistor and other side to the +rail... Then a 0.1uF cap.'s negative side With the base of main Transistor... Then a 10kohm res. With the positve side of the capacitor. Then a microphone (+) with the positve side of the capacitor and (-) to the ground.... It's not working... Can you plzz help me... It took almost a day but couldn't understand what I was doing wrong !

@eshanrajsrivastav5057 6 жыл бұрын

Thanks bhai...

@hamzamukhtarali4446 5 жыл бұрын

I followed every step of yours. The connection is like yours, but as soon as I plug the source the LEDs light up. Do you have an explanation please?

@MAKs_electech 5 жыл бұрын

Please check the circuit step by step.. Install we have tested the circuit for 2 transistors and then we completed the whole ckt so check it step by step it will definitely work..

@eymo9147 Жыл бұрын

Did you figure out why that happens?? I did it and the same problem happened to me

@microtec5384 2 жыл бұрын

Please add circuit diagram also

@emmansmburah18 3 жыл бұрын

its lit bro, thanks for the idea

@ShubhamParvat-xo6lw 2 ай бұрын

Can we make this without using 1M resistor

@nagaprasanna234 5 жыл бұрын

Bro the project was excellent but could u show the same project without using bread board please..

@kishanpatel2952 6 жыл бұрын

Ok bro thanks 👍and keep it up

@MAKs_electech 6 жыл бұрын

Is it working right now???

@kishanpatel2952 6 жыл бұрын

Bro I have tried all possible ways ,I have changed battery ,I have tried 12v battery . When I connect 12 v battery the rest 3 LEDs are working but without music and other 2 are not working even on music rethem. There is possible that microphone is not working properly?

@MAKs_electech 6 жыл бұрын

U just re connect the whole circuit may be the connection are wrong or you would have used a different type components by mistake or check the polarities of the transistor or the mic

@MAKs_electech 6 жыл бұрын

Most probably there can be the problem of mic bro plz check the positive and negative of small condenser mic....

@shahajanajji1079 7 ай бұрын

I tried doing the project, the LEDs are working but the microphone isn't working..I used the same microphone as it is used in the vedio...is it the fault of microphone or something else.. please help out..

@prasannaraj5285 5 ай бұрын

Yes mee to help pls

@eliezaraket5235 6 жыл бұрын

Can i add pic (microship) to the circuit and do a program to make for exemple 4 leds turn on and others turn off in the same time while the music is playing, and other question when i relate the microphone to a pin of the pic ofcourse it should be analog converter pin but should i do any changes or the pic will take as digital into it for exemple when the music turns on the input takes 1 from the microphone and the transistors with the leds will be relate each one to his propre pin should turn on and off depending on the music

@MAKs_electech 6 жыл бұрын

Yes u can do it.but, u don't need to use PIC Microcontroller's as it is a very easy circuit and u can inverse the output by adding another transistor in the ckt to get 4 LED's turn on and 4 LED's turn off. And for the next question u should try it because I haven't used a PIC. Thanks for taking interest into it.

@eliezaraket5235 6 жыл бұрын

MAK's thank u so much, i know that this project doesnt need pic but my doctor forced us to use pic in our project

@MAKs_electech 6 жыл бұрын

I can try, if I can get hands on PIC.😁😁

@shortsking4431 3 жыл бұрын

Sir, will it run on 3.7V ??

@kaustavjyotidas3261 4 жыл бұрын

😆😆😆 whoaaauuuh ....awesome dude

@MAKs_electech 4 жыл бұрын

Thank You So Much for Appreciation......

@nayananandu8392 5 жыл бұрын

circuit led is glowing but the mic donot work please give a solution for the problem

@nisargshukla 3 жыл бұрын

Check the polarity of the mic.

@cesaraugustop 3 жыл бұрын

Amazing video!! but, what i must to change if i want to use a source of 12v?

@varsha.m7053 Жыл бұрын

Pls reply once i connect the battery the leds are getting on

@rodinafurtado5177 5 жыл бұрын

Whooh😂😂😂😂😂😂😂

@mewishrehan1544 2 жыл бұрын

No output , i rechecked it , reassambled it, but not working , help me out

@madhavparihar7556 3 жыл бұрын

That's awesome

@azaruddinazar5453 5 жыл бұрын

Thanks for explaining it clearly.please help me .... what are the components need to drive 18watt submersible pump on music please reply or make a video.....

@MAKs_electech 5 жыл бұрын

Yeah we will see to it

@azaruddinazar5453 5 жыл бұрын

@@MAKs_electech I'm eagerly wating... make it fast as possible as...or mention the components please..

@rolex6743 7 ай бұрын

Can we use 100 micro farad instad of 100 nano farad

@pournamipournami9404 Жыл бұрын

I tried it Only lights are oned..... Nothing else is working ...What to do?..

@sivaom1567 6 жыл бұрын

super bro

@MAKs_electech 6 жыл бұрын

Thanks bro✌️

@pratiksurin5382 6 жыл бұрын

Behtariin bro 🙆

@MAKs_electech 6 жыл бұрын

Ty bro

@prakashdhankecha9396 5 жыл бұрын

hii , microphone is low sensitive. yes / no plz.. answer . this microphone is work high bass.plz reply me... this microphone is work on stereo on high volume

@MAKs_electech 5 жыл бұрын

Yes it is low sensitive, u can say that that's why it only bcoz of high noise 0r volume

@GabPampanga Жыл бұрын

what are my adjustments if I use 20 LED's? does it need to change the resistors also?

@tusharjagdale2235 6 жыл бұрын

Cool stuff ;)

@MAKs_electech 6 жыл бұрын

Thanks :-)

@MOHAMMADKAMRUZZAMANMILON 6 жыл бұрын

nice video.i am your new friend 527. support new creators.keep in touch. all the best.

@studynepalexperiment5746 3 жыл бұрын

100nF means 104 pF (Choose capacitor with 104 Written on it)

@priyanshukhambalkar7793 3 жыл бұрын

I just finished assembly of circuit but when I play music the light didn't react

@hariporiya2455 8 ай бұрын

why is my led always on "on" state ? and doesn't response according to music ??

@okashamohsin2280 5 жыл бұрын

Kindly explain the phenomenon upon which it is working(circuit explanation theoratically)

@kishanpatel2952 6 жыл бұрын

Out of 5 LEDs only 2 are working on music rethem but this 2 are dim . So how can I solve this problem

@MAKs_electech 6 жыл бұрын

Bro it must be the problem of ur battery check the battery and also check the connection from that transistor.....

@shamsahmed9512 5 жыл бұрын

I have connected everything as shown in ur vedio i followed ur all step the leds are just lighting but they are not blinking when i play music why??

@thantzinphyoe5568 2 жыл бұрын

Hello sir, LEDs are glowing if I use electret mic (pin type) or not. How can I solve that problem. LEDs not blink cuz of pin type mic???please answer Sir

@Hehehe46576 8 ай бұрын

It is wireless or not in music

@14apurvadane67 2 жыл бұрын

What is the future scope of this project plz help...?

@mr.rkknowledgeking8757 3 жыл бұрын

Pls 🙏 sir help me in this project... 100 nf capacitor ne. Badle 100 microfarad use thai???

@satavrutuja6735 5 жыл бұрын

Where we connect the DC switch ?

@MAKs_electech 5 жыл бұрын

U can connect it between the power supply and the vcc or ground i.e. +ve rail or -ve rail

@chetanbandi3 5 жыл бұрын

Can you provide theory for this project?

@ClashWithLove 5 жыл бұрын

Hello sir i have completed the circuit but the leds are simply on all the time they do not blink like how it was in your video and my first led is bright and the brightness gets lower and lower across the circuit plss help me

@nehaalone881 6 жыл бұрын

According to main transistor circuit how it's works

@MAKs_electech 6 жыл бұрын

The main transistor is the amplifiers of sound where all the others are used just to drive the LEDs

@Hari-kk7my 3 жыл бұрын

Niice.. Bro

@IdaKamali Жыл бұрын

hello.cathode of LED connect to Collector of transistor(middle lead)?

@patelmehul337 2 жыл бұрын

What principle was used in this project..???

@alexsalazar5121 5 жыл бұрын

How do i connect a microphone that only have a positive and a neutral wire?

@MAKs_electech 5 жыл бұрын

+be to the transistor or -ve or the neutral wire will be grounded but use the mic having +ve and -ve one so there will be no problem of output

@spaceadventurer100b8 5 жыл бұрын

Good video. Can you use led strip with this circuit?

@varsha.m7053 Жыл бұрын

Can we use disco leds ??

@WalkWithKamran 5 жыл бұрын

The leds not blinking its continously ON when i closse the switch plx help

@MAKs_electech 5 жыл бұрын

Please check with the circuit connection there might some issue in circuit...

@WalkWithKamran 5 жыл бұрын

@@MAKs_electech tnx its working now

@MAKs_electech 5 жыл бұрын

Good To Listen...😇

@prasannaraj5285 5 ай бұрын

Pls help anybody I'm construct same the all led goes on but they not dance with music they goes on always pls solve my problem

@ibex33 4 жыл бұрын

Circuit is working but in reverse, that is when volume increase the led brightness decrease, please tell me what's the issue brother.

@ZahirKhan-121 4 жыл бұрын

Can you tell me please what music to use. Send link of music video...

@meenakshichawla7933 5 жыл бұрын

What if i use a high value capacitor like 470 microfarad

@MAKs_electech 5 жыл бұрын

The LED's won't blink faster like the circuit so used the preferred one so that u can get the same output but for testing purposes u can do it output will be there

@divyamruthagangireddy5206 5 жыл бұрын

Can we use sound sensors instead of microphone

@astaher2800 5 жыл бұрын

Hi . Thanks for the clear steps and explanation .. I tried to make the circuit following the video but the leds flash from almost nothing even the breath of air not like yours .. I don't know the reason and how can I solve it ??

@calix_x 3 жыл бұрын

Try a smaller mic, or a less sensitive one

@calix_x 3 жыл бұрын

Or maybe leds with a higher limit