Today I will guide you to make a mini table saw. It uses a 775 motor so it is extremely powerful. If you find my video interesting, please like and subscribe to the channel! #diy #homemade #TNHcreative
Пікірлер: 26
@TNHcreative5 ай бұрын
Thanks for watching😊
@zodineliz42062 ай бұрын
Nice video... can you please listed all the materials you are using or provide a link to purchase? I have no idea how to search the material you shown just after the dc motor. And i can't find that steel shaft you are using.
@TNHcreative2 ай бұрын
Thank you for watching the video😊, you can search with the phrase "Pulley GT2" online and buy it, all the materials I have are in the video, and the saw shaft is an 8mm steel bar.
@HuyTran-vt1py5 ай бұрын
🎉
@sampathkumar301818 күн бұрын
So much complicated assembly is not needed. Just attach the blade with 5mm shaft adaptor ,fix in the mid portion and attach switch and socket for pin. It will be simple😊
@TNHcreative18 күн бұрын
great good luck! 😇
@raspberryPi13374 ай бұрын
Hi, so you have a list?
@TNHcreative4 ай бұрын
Hello, all the parameters I have are in the video🙂
@diacomservice4 ай бұрын
What is the wattage of the dc motor? thanks.
@TNHcreative4 ай бұрын
I found this motor in a drill, its capacity is quite large at over 180w
@diacomservice4 ай бұрын
@@TNHcreative thank you for the answer. I want to use 150w. But I don't want to use maximum power. I think a 10 amp power supply will do its job. By the way, what size strap was used? I think 200m might not be enough if a big knife is used. I'm thinking 280m. If the belt is too long, will it affect the power? More precisely, do you think it has an effect on the rpm speed?
@TNHcreative4 ай бұрын
@@diacomservice The saw may operate weakly if the power source does not have enough capacity😉. The belt does not affect the speed. If you want to change the speed, you must change the transmission ratio.
@diacomservice4 ай бұрын
@@TNHcreative transmission ratio ? Could you please explain this? By the way, my motor is 12v150w - I use max 15a then.
@TNHcreative4 ай бұрын
@@diacomservice In my video, I use a 16-48 pulley, the gear ratio is 1/3, for example you can change it to 16-60, it will be slower but more powerful. As for your 775 motor, it's great! 😊
@sampathkumar301818 күн бұрын
When you can attach a blade directly to the shaft why this belt ?
@TNHcreative18 күн бұрын
The machine runs fast, but when sawing it is very weak.
@sampathkumar301818 күн бұрын
@@TNHcreative So if you attach a belt does it retain the speed ? Some energy loss will be there through the belt but one advantage is the " shaft of the motor won't get damaged ".
@TNHcreative18 күн бұрын
I have shown in the video, everything has its principle, why I use a small pulley in the motor and a larger pulley in the shaft. If you find your design better, please share with everyone. ☺
@sampathkumar301818 күн бұрын
@@TNHcreative OK. Agreed.
@IqbalKhanbh5 ай бұрын
My question why you use pulley please reply
@TNHcreative5 ай бұрын
Hello, your question is very good. I use a pulley because I want to reduce the gear ratio and increase the torque
@IqbalKhanbh5 ай бұрын
@@TNHcreative please bro reply please please 775 DC motor 12v or car window motor 12v which is best for table saw please 🥺
@TNHcreative5 ай бұрын
@@IqbalKhanbh I use motor 775, pulley 16-48, you can see the machine works great! . As for the car window motor, I have never seen it before😅.