@BirckCox 5 ай бұрын
Great presentation, and a great design. I especially liked the fact that you included the installation of a built-in AC-DC power supply, rather than just telling the viewer to plug it into a bench power supply, then going on to something else. One question I have that no acrylic-bender-builder has bothered to explain so far: what is the purpose of the half-inch aluminum channel that gets mounted in the heating wire slot? Why is it there? What does it do?
@rikityrik 28 күн бұрын
Beautifully done. You did a bang up job with the design and a great job documenting and recording the assembly. Nicely done, thanks!
@rikityrik 25 күн бұрын
If you have a second could you answer a question. Would a PWM Controller serve the same purpose as the Relay you installed on yours. I’m trying to plan mine and love your plan but want to add be able to adjust the temp. Thought you may know, if not it’s ok. Thanks
@oscar5980 4 ай бұрын
Your guidance is excellent, just loved your video, quite comprehensive.
@mystreteacher 8 ай бұрын
Thanks for putting this out there. I was looking for some different for a bender because the other designs wouldn't accommodate what I need to do.
@homemadetools Жыл бұрын
Nice job. We shared this video on our homemade tools forum this week 😎
@bobdouglas2509 Жыл бұрын
Excellent video. Thank you.
@rezwonsharieff8261 Ай бұрын
What is the name of wire
@Erosgenuino Жыл бұрын
Espectacular trabajo, enhorabuena.
@mixme8655 9 ай бұрын
New subscriber always watching your videos ❤ many learnings😊
@Guishan_Lingyou 7 ай бұрын
Wow! Fantastic build. You probably now have the most attractive acrylic bender in the world. Even if you don't use it enough to justify the cost in time of building it, you can gaze at it with pride. But seriously, it looks great. Did the power supply and wire gauge combination work well? I don't know anything about bending plastic, but I would guess that as long as it gets hot enough without being way too hot, you don't need to adjust the power but instead can just vary the time you hold the plastic over the heat, so there is probably a lot of wiggle room for how much power the wire dissipates, is that right?
@DesireToInspire1 7 ай бұрын
Yes that's about right. I made this for a single purpose that i so far have not used it for. It will be used in a later build that I have been planing to do for 3 years now :) If i remeber correctly then it took me about 70 seconds to heat up the plastic so it was possible to bend, I never did get any burn marks. It is important that it go slow, that way the plastic get warm all the way though it and not just the surface.
@HarveyA 2 ай бұрын
Great project. Tried to get the plans from your Etsy store but nothing there 😞
@setesuper4611 2 ай бұрын
Great!
@marcosdasilva1615 11 ай бұрын
Excelente proyecto!
@diomedeslagrimas4154 Ай бұрын
What is the size of box?
@autovrum Жыл бұрын
Excelente, vou fazer uma, qual as medidas da mesa altura comprimento e largura? qual o comprimento usado do fio de níquel cromo?
@ragept4682 7 ай бұрын
Hello, thanks for sharing the video. Just want to ask out of curiosity, would it catch fire as i see commercial ones with water pipes and such.
@DesireToInspire1 7 ай бұрын
That is not something i want to test :D But what i can say is that the aluminium U-shape remove the heat very well so i have a hard time seeing how that would be possible.
@Bart_Depestele Жыл бұрын
nice, thank you
@whongthai1301 Жыл бұрын
post bend my acrylic starts to crack after a week or so - is it because of overtemp or bending it too soon ?
@DesireToInspire1 Жыл бұрын
Bending too soon.
@hendritresnahadi4146 7 ай бұрын
U used How mm thin of nikelin wire mr? Tx u
@kazlette 9 ай бұрын
Great video. I would love to know the specs of the power supply you used please.
@DesireToInspire1 9 ай бұрын
Then you should have watched the entire video :) 5:15 is what you are looking for.
@reddot-zt1fh Жыл бұрын
Can you get electrified where the exposed cables are?
@DesireToInspire1 Жыл бұрын
No, it's only 12v
@reddot-zt1fh Жыл бұрын
@@DesireToInspire1 ok, all this wires work with 12v?
@DesireToInspire1 Жыл бұрын
@@reddot-zt1fh yes, it all depends on the current.
@reddot-zt1fh Жыл бұрын
@@DesireToInspire1 Thanks.
@keithm2276 Жыл бұрын
@@reddot-zt1fh hi what about amps is it governed by the power supply or the resitance of element wire
@LarsDunemark Жыл бұрын
Ser at du också har Bosch pelarborr, skaffade en likande för någon vecka sedan, upplerver du också att där är mycket glappa i chucken? Tycker att mina borr wobblar ganska mycket och känns svårt att få ett hål i centrum av var jag börjar då det gärna vandrar i väg 0.5-1mm i sidled.
@DesireToInspire1 Жыл бұрын
Har faktiskt aldrig tänkt på det. Upplever inga problem alls.
@thecat3419 Жыл бұрын
Fiffigt! Tumme upp!
@whongthai1301 Жыл бұрын
DC low voltage / more burn than shock
@user-wb1up5py2l 9 ай бұрын
please share the details of power supply and nichrome wire
@DesireToInspire1 9 ай бұрын
In the video i show all details you ask for, watch it again and you will see :)
@holidayeasterbrook 5 ай бұрын
beautiful job! where did you buy the spring/what kind is it? I ran into the same problem with ours,, spring not pulling wire enough...and then spring snapped when I pulled it tight!
@TPL034 3 ай бұрын
Hi, what is the length of your Nichrome Wire when cut and attached on the Aluminum U channel?
@9860899143 Жыл бұрын
Is this machine available for sell
@DesireToInspire1 Жыл бұрын
Sorry no.
Desire to Inspire
Рет қаралды 92 М.
aecfun
Рет қаралды 833 М.
Desire to Inspire
Рет қаралды 22 М.