Happy new year 2021😅

Is cheap Arduino uno r3 capable for replacing Servo Tester?

The point is that the experiment is being shared. We can watch this and learn. For me, this shows why gears are needed - this drill is too fast and low-speed torque is needed in many situations.

Volt ?

@@ahmetahmetoglou8780 this motor works in 11.1-36V

This is expensive fake prop drill of no value yes

Everything is true. But you can't buy feeling of creating something by yourself. Just ask your parent about how grateful they are when you has born, they are not bought you from shop in heaven.

True. But the same design can be used to make a lathe.... Etc

@@PTechMedia actually to make drill is not just slap motor to the chuck..but it actullay consist of gear box. which this design lack...10-20k RPM is good for RC car which what this motor mostly use for. Even RC car still have gear box. Smaller motor tend to have high RPM but less torque. But gearbox make those loses to torque. Gearbox convert those high RPM to torque by lowering its RPM and converting those energy to bigger torque which is what drill is needed. Drill need torque to drill especially when you tightening screw or loosen the screw. Believe me this thing wont even move the tight screw..even with with 40-50nM some screw are so hard to loosen or tighten...same principle with lathe or etc, most of those application so much in needed for torque not RPM alone. And most of bigger motor tend to have high torque with lower RPM. Because bigger motor mostly use in those application for lathe and etc. so you wont need much complicated gear conversion rather than just use belt system with some adjustment. This project is great for DIY to build but not for practical use, cheap cordless drill is still way more convenient because have torque conversion which is what important for cordless drill.

@@slyztercoreveanged3175 a drill isn't a driver. You can drill with low torque depending on materials. And my mini drill tool is useful and only controlled by voltage input switch

@@slyztercoreveanged3175 think dremel

Are you serious say this or are you joking this bldc motor is rated for 1200watts up😅😆😆. Chill with your 30watts 😂😂

T In this video he run on 6v x 20amp= 120watts

no shit sherlock it doesn't have a gearbox. it goes 30k rpm. it'd be great for a PCB Drillpress though

It'll be uselesss for many tasks

Thank you

正负两极5伏

还有三个是接霍尔输出的

Probably he was drilling through a brick with it

@@cash3394 but i dont think so it is capable of it

@@himanshukalra6118 that's a strong little motor. It's obviously not gonna drill a very big hole but I'd bet it would drill a small hole in concrete with the right bit

@@cash3394 who knows

Start small and I'm sure it will. Even my professional battery hammer drill should only be used to still up to 8mm deep in bricks... (Although it often goes a good 50mm)

Yesssssssssssss....high speed is not required for the drill

No bro this type of motor have huge torque this is why this type of motor used in power full electric skate board without any gear box . this motor kv rating is lower than 200kv

@@tiktokvideos5025 let's see drill metal and concrete or use screwdriver some long screws

Безщеточные стоят от 150$ в лучшем случае, правда, со всеми прибамбасами, реверсом, поавноугасающей подсветкой 2-3-скоростным редуктором и противоударным эргономичным корпусом с индикаторами разряда и т.п. Но и приводить в пример дешёвые китайские поделки на копеечных моторах на угольных щётках как-то странно. Здесь просто показали концепт. Дальше можно совершенствовать в сторону удобства, недостижимого для готовых вариантов, например, напечатав на 3Д принтере корпус, можно получить сверхлегкий, сверхкороткий аппарат для узкоспециализированных целей.

@@NyyphoHerr-3D-panorama насадки для щелей 200 руб🍾😁

В магазинах шуруповёрты и дрели на коллекторных двигателях, а в видео на бесколлекторном двигателе.

literally every drill costs $100

@@alexanderthegreatish4079 Well there are some cheaper. And also then whats the point of making it rather than purchase it.

where on earth we can a fresh gear unleash u get it from a broken drill...

Hong Kong

Thats my question too

It is one packed in battery box dude

ну за 3000р на безщёточный шурик на литии не найти,а вот щёточный можно. плюс здесь двигатель очень быстро выйдет из строя, так как идёт прямое давление на него, без редуктора, что недопустимо

Если уж ты споришь - специально для тебя посчитал - 4 косаря без учета зарядника. Безколлекторные шурики начинаются от 4.9 в полном боекомплекте с гарантией и само собой на литии. А уж с обычными моторчиками за эти деньги - ну просто ассортимент.

To make a DRILL.

hahahahah

yes

No. There is no gearbox or impact mechanism involved. Direct drive off the outrunner shaft to the chuck.