How to Make Epoxy Cutting Board | Step-by-Step Guide |

Рет қаралды 12,954

7 ай бұрын

Would I be a real KZfaq Woodworker if I did make a video on how to build an EPOXY CUTTING BOARD? Maybe, but this project was too fun not to share.
In this video, I walk you through the entire process of creating a beautiful epoxy serving board. I will also give you tips on preparing lumber for the epoxy pour, how to design the boards, and how to get bubbles out of your epoxy pour.
I would also like to thank Crafted Elements and Total Boat for making this video possible. See the links below for the mold and epoxy that I used in this video.
Like this video? Here are five more you will LOVE:
Camp Chairs: • EASY Camp Chairs | Beg...
Chaotic End Grain Cutting Board: • How to Make a Chaotic ...
End Grain Cutting Board: • How to Make End Grain ...
Easy Cutting Board: • How to Make a Beginner...
Tips to Save Money in Woodworking: • Woodworking Tips | How...
See Links below for products and tools used in this video🧰
Crafted Elements Mold: craftedelements.com/products/...
Use the link below for 5% off Epoxy Resin
TotalBoat 1" Pour Epoxy: www.totalboat.com/products/th...
Black Diamond Pigments: www.totalboat.com/products/mi...
Tools I used in this video (Amazon Affiliate Links) 🧰
SawStop Table Saw: amzn.to/40cXY3m
Powermatic Dust Collector: amzn.to/499VZRs
3M Ear Muffs: amzn.to/40jmCiH
Respirator: amzn.to/46PJhpd
DeWalt Planer: amzn.to/40dmyAY
Caribbean Blue Pigment: amzn.to/3QAsSzv
123 Blocks: amzn.to/3QyOJY6
Propane Torch: amzn.to/49fDgUs
Bosch Palm Router: amzn.to/3QA57qb
1/4" Router Bit: amzn.to/3Qeww0C
Craftsman Sander: amzn.to/3sk2GzA
Butcher Block Finish: amzn.to/3QBxyFm
Foam Brushes: amzn.to/3QxPdNY
Finishing Triangles: amzn.to/3SeqgIR
Filming Equipment 🎥
Gimbal: amzn.to/3MkvG1g
Iphone Mic System: amzn.to/45T5ul7
External Hard Drive: amzn.to/3tsQuNE
As an Amazon influencer, I profit from qualifying sales, which helps me bring you more helpful woodworking content.
Subscribe to the channel here: / @ben_grimsley
Check out my Etsy shop here: boardsbyben.etsy.com
Thanks for watching!
‪@TotalBoat‬ Ambassador
#woodworking #cuttingboards #epoxy

Пікірлер: 59

@Ben_Grimsley 7 ай бұрын

Like this video? Check out this video on making an end grain cutting board: kzfaq.info/get/bejne/is98lMSatuDUd5s.html

@jackiewalsh7032 3 ай бұрын

Great video. I have been slowly adding woodworking equipment into my stash. I had an epiphany the other day that made me change my mind. I am 787 months, 23,940 days, 574,600 hours, 34.48 million minutes, 2.069 billion seconds old, that‘s an eye opener (I thought I wood 😉 throw that in to test your math skills) With all that said I am too old to invest that much money into a short lived hobby. Not only that it probably isn’t worth the risk of cutting off fingers when my body is already showing signs of wear and tear. I will live vicariously through you and other amazingly talented artists enjoying your work. BTW Alexa did the math for me.

@ITtutorjack 3 ай бұрын

I really like this video! Thank you so much for making it. This video is a lot more clear than other videos I've watched -- other videos don't talk nearly as much about the specific products and tools they use. Your video makes me believe I can make one myself, and there were so many helpful tips and tricks I learned from this video. Not only that, but I really admire your contagious enjoyment for the work you do. I'll definitely refer back to this video.

@Ben_Grimsley 3 ай бұрын

I am so glad it was helpful! That is why I make these videos. Thanks for watching!

@ITtutorjack 3 ай бұрын

@@Ben_Grimsley That is such a great skill to be able to do things like this. Best wishes to you.

@rebeccayounglove4104 16 күн бұрын

Love to see a video on types of timber , burls etc . This was a great video . I don't have all those fancy tools but have the basics . Would i still get a good result

@Ben_Grimsley 14 күн бұрын

I say go for it!

@edwinbarreto58 18 күн бұрын

Truly brilliant tutorial; easy to follow. Thank you

@Ben_Grimsley 14 күн бұрын

Glad it was helpful!

@damonyeary Ай бұрын

The cutting board looks fantastic. Thank you for the video! I may try on of these soon

@Ben_Grimsley Ай бұрын

Thank you! Give it a try. They are a ton of fun to build!

@mlbuxbaum 4 ай бұрын

i just bought that exact Crafted Elements mold to do exactly what you are showing. Great video. Very informative

@Ben_Grimsley 4 ай бұрын

You will love it! Glad the video was helpful. Thanks for watching!

@TotalBoat 7 ай бұрын

This turned out awesome! Beautiful work!

@Ben_Grimsley 7 ай бұрын

Thank you so much! Would not be possible without the amazing products you guys make!

@RandomCamShorts 2 ай бұрын

Actually a fire video! Thank You for your tips

@Ben_Grimsley 2 ай бұрын

Glad it was helpful!

@fernandofonseca6326 6 ай бұрын

😊BEAUTIFUL BRO ,GOD BLESS YOU AND YOUR FAMILY

@Ben_Grimsley 6 ай бұрын

Thank you!

@andrewlloyd4702 Ай бұрын

Hi Ben, can you please give me the name of the butchers block oil you used, I've recently started fractal burning, I'm looking for a reasonably priced mould so I can start to make boards like the one in your video, as I already cast in resin, i must compliment you on the video and your presentation, so relaxing to watch, I'm in Wales in the United Kingdom, best wishes to you and your family. Keep up the great work. Andrew

@kennypapi-chulo9292 7 ай бұрын

New sub here. Good job. I am a huge Crafted Elements fan and our shop has over 30 different molds that we use. On my river projects, I like to apply a single coat of epoxy to the inside live edge walls to help cut down on bubbles and it helps with adhesion. (I had a few pop apart in my very first smalls pours years ago). Your board came out just fine. Thanks. Kenny - Tampa

@Ben_Grimsley 7 ай бұрын

Thanks for the sub! Really appreciate it! As far as the live edge coat of epoxy goes, I have seen people do it both ways. I actually heard someone say if you apply an inside coat, it makes the joint weaker. I will probably try both ways to compare the results. Thanks for watching!

@inspectr1949 7 ай бұрын

Good question with ways.@@Ben_Grimsley

@icecreamladydriver1606 3 ай бұрын

Very nice.

@Ben_Grimsley 3 ай бұрын

Thank you so much!

@inspectr1949 7 ай бұрын

Many say on this subject that one should seal the joining edges of the wood 1st before pouring in the epoxy so as not to continually introduce additional bubbles.

@Ben_Grimsley 7 ай бұрын

I have heard that, but I have also heard woodworkers say this makes the joint between the epoxy and wood weaker. That's why I avoided pre-sealing the live-edge in this project. I may try in a future project to see how it works!

@andrewlloyd4702 Ай бұрын

I've found the brand of butcher's block oil, my question is, did you resin it after the butcher's block? Thanks Andrew.

@Ben_Grimsley Ай бұрын

Hey Andrew! I want to make sure I understand the question you are asking. I let the resin cure and then applied the butcher block finish. Does this answer your question? Thank you for the support! It means a ton!

@fatheransonfishing2723 Күн бұрын

Besides cleaning off any excess bark etc did you happen to seal the timber first with epoxy before your live edge pour? I’m new to this and keen to give it a crack but I have mixed feelings as I’ve heard others say you must seal and yeh

@Ben_Grimsley Күн бұрын

I did not seal the edges first. I have heard mixed reviews on if this is necessary or not. From what I gathered, it helps prevent bubbles. But I personally do not think it is a necessary step. I hope this helps!

@rustydegeorge5726 2 ай бұрын

Great informative video! Been looking at that same mold from Crafted Elements; after your video, about to purchase one. What specific pigment color did you use in this video?

@Ben_Grimsley 2 ай бұрын

I believe it was "Caribbean Blue" from Black Diamond Pigments. There is a link in the description of this video that will take you to the exact pigment I used. Thanks for watching!

@deepakchouhan1710 26 күн бұрын

Am from India but I want to work with you sir

@michaeldequatro1012 3 ай бұрын

Great video and very easy to understand. I have 2 questions. What color blue did you use? I know there are dozens of different blues out there. Also, can you use that as a cutting board? Will a knife cut the epoxy?

@Ben_Grimsley 3 ай бұрын

Thank you for watching! I use Black Diamond Pigments for all my epoxy projects. The exact color is "Caribbean Blue." If you look in the description of this video, you can pick up this pigment from TotalBoat and save 5% on your order. I would not recommend cutting on this board. I sell them as "serving boards." There are mixed opinions on this, but I would rather be safe than sorry! I hope this helps! Thanks for watching!

@michaeldequatro1012 3 ай бұрын

Thank you so much@@Ben_Grimsley

@OutinthewildAZ 28 күн бұрын

Nice board. How much you think you can sell that for?

@Ben_Grimsley 27 күн бұрын

I would price this board for about $100! Somewhere in that ballpark

@wharfrat360 7 ай бұрын

Other than KZfaq what social media are you most active on?

@jackandred 2 ай бұрын

This was fantastic. You make this project look so approachable. I’d add handles to perfect it. 🩵💙

@Ben_Grimsley 2 ай бұрын

Thank you! And that is a great suggestion. I will try this in the future

@user-ss5vc3mf6q 4 ай бұрын

So I have an foxy project that will be my first one I have to make custom calls for any suggestions

@wc3957 2 ай бұрын

👍...question. if you cut on the board does the epoxy come off?

@Ben_Grimsley 2 ай бұрын

I have heard mixed reviews on this. I personally would not cut on it, but I know of people who do!

@michaelcannon9271 23 күн бұрын

How well does epoxy behave as a cutting board? You have comments below about plastic getting in food, etc. But does it scratch a lot and get to a point that it does not look good?

@Ben_Grimsley 14 күн бұрын

Personally, I would not cut on this. I have heard people say you can, but my philosophy is better safe than sorry

@blt981 Ай бұрын

What size is your SawStop I’m researching one as a newbie work worker. 3 hp or smaller one size of table top

@Ben_Grimsley Ай бұрын

Mine is 1.75 HP and it has been great for anything I have had to tackle, including cutting through thicker slabs. Another nice part about the 1.75 HP is you don't need to re-wire your shop to install it. I have link in the description of this video to the saw I have. Hope this helps!

@blt981 Ай бұрын

@@Ben_Grimsley thank you for taking time from your busy life to respond back to an a 67 yr old retired Police Officer. Kids all gone my best friend who is my wife and always supportive, teases me about my tools and guns but is happy to get house projects done from my work. Still chase her around the hose if u know what I’m saying. Thanks again peace and love. FLATTFOOT Forever….

@dougward6669 4 ай бұрын

What is that you are using as a coating?

@Ben_Grimsley 4 ай бұрын

It is a food safe Butcher Block finish. There is a link to the exact product in the description of the video. Hope this helps!

@caseymorgan2112 5 ай бұрын

Your method of removing the bark is fine but why not use a chisel instead?

@Ben_Grimsley 5 ай бұрын

I believe I may have off camera. I use chisels a good bit for removing bark, but I always want to be careful not to scar the wood. Thanks for watching!

@deborahrouchon7740 6 ай бұрын

So the title is “Epoxy Cutting Board” which is (or should be) a contradiction in terms. But I guess that was just an error because you never called it a cutting board. Good call. Nice board.

@Itsreallymarcus Ай бұрын

It’s not an issue to use epoxy on a cutting board.. if you’re simply cutting on it.. you’re never going to get plastic in your food.. and if you somehow did, it’s not anymore plastic your eating and drinking anyway… epoxy is safer than 100% of the processing and chemicals added to your food in America anyway lol

@deborahrouchon7740 Ай бұрын

Epoxy resin is food safe after fully cured,, never food grade, and therefore is not safe to be ingested. The longer that epoxy resin is cured, the more it acts like glass when machined, such as cutting with a sharp knife. It will eventually chip into shards like glass and could be very dangerous to swallow. Perhaps you should speak with your resin company?