How to make less boost ex: (0-7 PSI) on an 8 psi wastegate. Explained on my 2005 Jeep Wrangler TJ turbo kit.
Пікірлер: 41
@MrEddiedding3 жыл бұрын
Great Idea thank you very much
@kieculpitt4075 ай бұрын
Very smart..... thanks!
@JWheelie2 жыл бұрын
AWESOME video! Where can i find a skinny spring like that?
@miguelrosales5598 Жыл бұрын
Gracias 🙂
@kyfiss91764 жыл бұрын
I saw you were looking for a 2.5l to mock up a kit. I've a 95 YJ and a 97 TJ in Texas if you're interested. I'm not sure where you're located though.
@christophl8384 жыл бұрын
hey! exciting stuff and great quality. Any chance to do something with the I6 4.0 engine?
@zackfab88474 жыл бұрын
Hoping to have a 4.0 kit soon!
@brucebell76234 жыл бұрын
Zack are you located In rocklsnd Couty NY? May need fab work done on my On 3 turbo kit for my fox body mustang??
@gusamaya29342 жыл бұрын
What spring is that from, name and where to buy them?
@SharkFishSF2 жыл бұрын
Is there any kit to turn off turbo in modern cars?
@bt619x Жыл бұрын
Until the spring gets hot from the exhaust heat and weakens. How is this running now?
@midgard91363 жыл бұрын
What is the length of the spring?
@BulliKid3 жыл бұрын
how much boost does it run now?
@2davydo4 жыл бұрын
Thanks for that tip man. Never thought of that. Would this work for a T3, T4, T4E cheap Ebay $100.00 chinese turbo. With the pre load set to 8psi. The one
@zackfab88474 жыл бұрын
Yes this will work with any turbo!
@brucebell76234 жыл бұрын
Zack are you located in Rockland County NY??
@johnnymwmadden3 жыл бұрын
Are you going to be bringing these turbo kits back to production? Weighing our options and considering turbo kits for our 04 TJ
@EAGLINWRX Жыл бұрын
What did you end up doing?
@drewfarrow6466 Жыл бұрын
I luckily just got one of his kits second hand but if you guys are in need of something I have a half finished manifold
@Eastern_SA3 жыл бұрын
How to increase the boost say from 8 to 12 or 15 psi? Can you do it by just adjusting the WG rod or it require additional spring?
@S4ndSt0rmVideo2 жыл бұрын
The way you do this is by adding a bleed valve, which is basically a controlled leak in the feedback the wastegate is getting. Say you have an 8 psi wastegate and you want 12 psi of boost. You introduce a bleed valve into the hose that goes to the wastegate and leak 4 psi of pressure with it. The wastegate still opens when it gets 8 psi, but there actually is 12 psi of pressure in the intake.
@nagrain3 жыл бұрын
How about just extending the rod to make it longer?
@amjedahmed85093 жыл бұрын
You can do that but avoid not to keep the valve opened slightly by extending too much.
@enmanuelramirez7163 жыл бұрын
Hey guys, I have the next question ! My turbo spools around 1800rpm full boost around 2500rpm, but start to lost psi after, 4.400rpm ? How can I make turbo spools after 3k rpm? Cause I’m loosing all the power after 4500rpm.. thank you ! Greetings from Costa Rica 🇨🇷
@jakobpoole76222 жыл бұрын
Might have to look at a bigger A/R on the turbine side. This does however change the full boost range to higher in the RPM. Just have a little look at what changes with smaller and larger A/R's. I hope this helps
@mehling804 жыл бұрын
Any luck on starting a kit for a 2.5 ?
@zackfab88474 жыл бұрын
Still looking for somebody local who will let me use there jeep for mock up
@111soreal3 жыл бұрын
Correct me if I’m wrong. The spring you put in place. Makes it open earlier
@amjedahmed85093 жыл бұрын
Yes the guy is aiming to lower his boost level
@nickpetrillo83002 жыл бұрын
How though? The spring never affects the exhaust pressure. So unless the preload spring is 7psi the exhaust won't open sooner than 7psi.
@mauricio57632 жыл бұрын
Re watch the video
@dennisrobinson80082 жыл бұрын
to lower the boost decrease the preload on the internal springs by shortening the rod?
@agelast98312 жыл бұрын
shortening the rod will create more pressure on the spring making the gate harder to open, shortening the rod will increase the amount of boost needed to open the wastegate. There is no way to make the gate open at less boost than it was made for, unless you do something like this in the video.
@dennisrobinson80082 жыл бұрын
@@agelast9831 The spring trick, to lower the effective tension of the spring. Good to know.
@nickpetrillo83002 жыл бұрын
The waste gate only triggers at 7psi. So how does preloading the spring change anything? 4psi of exhaust plus the spring doesn't mean 8psi. Your exhaust still has to hit 7psi on its own. The spring is just sqeezed more. I think a weaker spring would be the only simple solution
@zackfab88472 жыл бұрын
Try and watch the explanation. Its explained pretty well. Pressure = Force/ Area. Reduce the Force needed to open the gate (aka add the spring) = less psi needed to open the gate..
@jeeperzcreeperzz4 жыл бұрын
Whats your email? If I payed you could you sell me a turbo kit or list for my 4.0 using the stuff that you used for your build
@zackfab88474 жыл бұрын
Email me ZackFab171@gmail.com happy to help
@wesleynelson8263 Жыл бұрын
This looks like wastegate "crack" pressure to me.
@zackfab88474 жыл бұрын
Hey Guys, Selling an improved and more powerful FULL Turbo/exhaust kit as well as a Naturally Aspirated Performance exhaust kit. Email me ZackFab171@gmail.com for any questions To ORDER check out: ZackFab.com