How To Mig Weld SUPER Thin Metal with (NO WARPING)

Рет қаралды 213,345

2 жыл бұрын

In this video I show how to set up your mig welder to be able to weld on super thin metal with out warping it. I go through step by step comparing how to prepare your metal, how to tac and how to use a hammer and dolly to control your metal. Hope this helps and thank you for watching. God Bless Adrian at AC Designs Garage. Below are some of my supplies that I used during my video.
Check out my Tshirts available only at www.acdesignsgarage.com
These links are provided to you at no additional cost from my amazon affiliate account.
0.023 mig wire amzn.to/3iHHmMd
miller digital elite welding shield amzn.to/36SXHuV
DA Sander amzn.to/3iFd0K8
gopro hero 10 amzn.to/3Lfw65Z
canon m50 amzn.to/3NkGs6x
rode mic amzn.to/3NpqSGt
tillman mig gloves amzn.to/3iCil4P
4.5"x 7/8" 60 GRIT FLAP Wheels amzn.to/3LtntoK
4.5"x7/8" 80 GRIT FLAP Wheels amzn.to/3KqjFTS
4.5"x7/8" inch CUT OFF Wheels amzn.to/3Lsd78N
Dewalt Electric side grinder amzn.to/37VFMV0

Пікірлер: 328

@timmer9lives Жыл бұрын

Best video I’ve seen on mig welding lighter gauge metals

@ACDesignsGarage Жыл бұрын

Thank you for the kind words and support 🙏

@lewandlo Жыл бұрын

If you have a piece of copper plate or even a piece of copper round pipe clamped against the back of the gap to take your heat away will work. With that gap, you have to get a heat sink behind it to cool down the weld. Also if you want less warpage you have to tack every inch first then then alternate again with your tacks until you fill up the gaps between tacks. Cheers

@JohnnyBailey-jq1qm Жыл бұрын

Can do that if you’re sectioning in a quarter panel and have no access behind the panel

@edyy6619 Жыл бұрын

@@JohnnyBailey-jq1qm thats the only part i hate doing quarters like 30 minutes to weld 6inch bead unless you do metal backing helpsm

@JohnnyBailey-jq1qm Жыл бұрын

@@edyy6619 it does help, now they act like it’s so scandalous to do if the manufacturer doesn’t allow it but whatever. There’s a lot more pros than cons to it

@edyy6619 Жыл бұрын

@@JohnnyBailey-jq1qm yeah they want procedures to be done correct but sometimes you cut your panel to big end up with a wide gap to weld. Id rather have a backing have my welds hold than risk ripping off the whole section in an accident.

@FixingWithFriends 10 ай бұрын

I figured the last part out since it seems logical, but having a backing is a great suggestion. (when possible)

@iwalkalone1 3 ай бұрын

Excellent video!! I learned a couple things that I had never even considered before.

@ACDesignsGarage 3 ай бұрын

Awesome, thank you for watching!!!

@dennis6325 2 жыл бұрын

If you are running 75% Argon / 25% Co2, why did you read off the chart on your welder for 100% Co2? Just a mistake I assume. I used 20 CFH regardless, but then I did a little experiment and discovered I can really turn it down for thin sheet metal. Now I go thru the gas half as fast and the welds are the same quality. I weld thin gage steel exactly like you have shown. No gap and as high a heat as I can get that bacon to sizzle without blowouts. Good Job!

@ACDesignsGarage 2 жыл бұрын

Lol my mistake, trying to remember all the crap I have to say, I get tripped up sometimes lol, I dont script my videos, but I probably should hahahaha thanks for watching!!!

@glassgubbenfg Жыл бұрын

Hi, I have a little tip, I have been welding in thin sheet metal for many years and I can see that you are pointing the welding wire and the heat towards the hot points, try pointing the welding wire and the heat away from the points instead. if you do that, you point the heat at colder metal and you don't burn through as easily

@ACDesignsGarage Жыл бұрын

Thanks for the tip ill try that.

@joeybuddy96 Жыл бұрын

Thanks for making this demonstration! I'm just watching as many videos on car metal as I can and this is helpful.

@ACDesignsGarage Жыл бұрын

Thanks for watching ,so glad it helped!!!!!

@bennymcmunn9683 Жыл бұрын

Very informative and helped me to understand the differences of metal movement. Very nice video. Look forward to seeing more of them. Thanks

@ACDesignsGarage Жыл бұрын

Thank you, I hope it helped. Im filming another one this week. Thanks for watching!!!

@TheGoldinge Жыл бұрын

Thanks for your response my friend, very helpful,!

@michaelballance8055 2 жыл бұрын

Thank you so much. I have watched a ton of videos on welding. I struggled years ago with my youngest son on shaving a VW GTI doors. Three sets of door panels finally got it. Wish I had seen this years ago. This was the most informative video I have seen on developing the correct MIG process for thin metal

@ACDesignsGarage 2 жыл бұрын

Thank you very much, so glad I could help!!!!

@BOREDANDWELLBORED Жыл бұрын

@@ACDesignsGarage what amperage are you on? I'm new. I got the wire speed but don't know what "1 volt" you mean 100 volt? I'm still shopping for mig welder.

@BOREDANDWELLBORED Жыл бұрын

@@ACDesignsGarage I'm buying a gasless flux mig so I can build my van. Would you be able to weld thin metal like this video using gasless flux mig?

@copisetic1104 4 ай бұрын

I use a jeweler’s torch with oxyacetylene on 22 for expansion chambers. Hold the flame tangent to the curve of the two cones then bring the the inner flame in to fuse the joint, with practice you can walk around a curved or flat pretty fast. Adjust the torch to a fine flame cone. I don’t use any rod just fuse the joints together. I’ve never had a broken pipe. Every one uses tig or mig, but I think oxyacetylene with a fine 000 or better works well a lot faster than either tig or mig.

@ACDesignsGarage 4 ай бұрын

Awesome, id love to try that!!!!

@enigmasvids9615 10 күн бұрын

I still use an oxy/acetylene set with a Dylan/Cobra/Henrobe hand torch. It uses fine, small precision torch tips and is fantastic in thin sheet metal with practice. It's also a great tool for brazing and silver soldering. Oxy/Acetylene torches are something of a lost art these days with all the electronically controlled welders available today. I still have a 30 year old fully manually adjusted MIG welder that I use for welding heavier/thicker steel pieces together. Great presentation.

@gala83filmstaylorg7 11 ай бұрын

Running into it right now..first time ever welding and your video is definitely helping so thanks!

@ACDesignsGarage 11 ай бұрын

Awesome so glad it helped!!!!

@keepersoftheearth6637 Жыл бұрын

Thank you for this, I've been working with thin metal trying my hand at some art, this was very helpful

@ACDesignsGarage Жыл бұрын

Awesome hope it helped, below is a link to video I did a while back on making a rose from sheetmetal if you want to check it out. kzfaq.info/get/bejne/pp-CftN9xpe1e5s.html

@CraigHollabaugh 6 ай бұрын

Found your channel yesterday, after watching this, I need to completely scrap my whatever approach to welding sheet to follow your recommendations here. I'll pick up some pieces from my local metal yard cut bin and start my re-education. Thanks AC.

@ACDesignsGarage 6 ай бұрын

Thank you for watching ,I hope it helped you!!!

@CraigHollabaugh 6 ай бұрын

@@ACDesignsGarage It helped today. I'm working on a 'low poly garden sculpture' and focused on edge alignment over jump gaps. Also tweaked welder, got great small tacks like you showed here. Thanks again.

@eddiejeselink2996 16 күн бұрын

Great video, thank you wish I found it sooner.

@ACDesignsGarage 13 күн бұрын

Thank you very much for watching!!!

@styson127 2 жыл бұрын

Thank you. Picked up a few tips. Trying to teach myself MIG welding and blowing holes. Will try increasing the feed rate. Still practicing before I tackle rocker panels.

@ACDesignsGarage 2 жыл бұрын

Your doing it right, practice on scrap first! If you have any questions let me know!!!

@henryworkswoodandmetal Жыл бұрын

Excellent presentation, really well explained step by step…….. thumbs up 👍

@ACDesignsGarage Жыл бұрын

Thank you very much!!!!

@vojislavcar6157 3 ай бұрын

Tip: putting the thick copper plate below. Tight to thin plate before welding. Use wire Weldinger SG2 Ti, 0,023’.

@ACDesignsGarage 3 ай бұрын

Awesome thank you for the tips!!!

@NialPowerCork Жыл бұрын

Very interesting and informative, thank you. Going out now to give it a try!

@ACDesignsGarage Жыл бұрын

Awesome go for it, thanks for watching!

@Papachurch8 Жыл бұрын

You have been a huge help. I’m restoring a 68 short bed ford all my self. Not the best welder. I’ve built roll cages but never any body panels till now

@ACDesignsGarage Жыл бұрын

Awesome thank you, so glad I could help. I had a 67 f100 short bed years ago, wish I still had it!!!

@edsmachine93 11 ай бұрын

Nice work. Thanks for sharing the process. Take care, Ed.

@ACDesignsGarage 11 ай бұрын

Thank you and thanks for watching!!!

@babasolabada7793 Жыл бұрын

Thanks for the demonstrations. It's quite helpful. Cheers.

@ACDesignsGarage Жыл бұрын

Thanks for watching!!!!!!

@mikekahotea8148 Жыл бұрын

I enjoyed watching the video and appreciate the time effort and coverage of the work done 👍

@ACDesignsGarage Жыл бұрын

Thank you very much!!!!!

@taxicamel Жыл бұрын

Not actually stated is ...LESSON LEARNED ...."no point in using a gap when welding thin material" ......now begin experimenting with the settings. And by the way, this is NOT "SUPER Thin Metal" ....not even close. .

@cliffordd6444 Жыл бұрын

100% agree on the practice on scrap and CLEAN metal (not ground too thin)

@Pohleece222 Жыл бұрын

Thank you. Very informative.

@ACDesignsGarage Жыл бұрын

Thank you!!!!!!

@brianhamalainen8817 Жыл бұрын

MIG welders do add more amps with the wire feed speed; so turning up the 'speed' also turns up the power/heat. That's why your chart for C25 suggested '1/12' for 22g. Have you not noticed that the arc/puddle/HAZ is much larger/brighter on 'higher feed'?

@SwedesGarage Жыл бұрын

Might be true on newer MIGs, but my old one from the 80's don't change the amps with wire speed.

@janeblogs324 Жыл бұрын

All MIGs do it. From buzz boxes to inverters

@truracer20 10 ай бұрын

It only really comes into play on continuous welds. With this type of tack welding the extra wire feed tends to cool the puddle. A lot of welders think their beads flatten out towards the end of a long bead on thick metal because of heat soak allowing the puddle to flow when in fact the amperage is rising to accommodate the wire feed rate which the hotter metal allows for. With short circuit wire feed welding high wire feed rates cause a more continuous short circuit raising the amperage, a dead short (most amperage) is sticking the wire, the slightest short (least amperage) is when you burn back to the tip. One dial is Voltage the other dial is wire speed, so amperage is a factor of the 2. I'm sure some expensive new welders can adjust this effect but if you only have Voltage and wire feed settings on your welder then wire feed rate absolutely affects amperage.

@williamblair2934 2 жыл бұрын

Thanks Adrain. Be blessed

@ACDesignsGarage 2 жыл бұрын

Thank you very much!!!!!!

@lonnieciallela1526 Жыл бұрын

thanks for this video I think its gonna help my problem I was having welding thin stuff. I discovered 3 things I was doing wrong from this. one was using my roll lock to clean the metal. two was I was turning heat and wire speed down when I blew thru. and three IM NOT A WELDER hahah. its alot harder than it looks Ill post an updater when I get at my project

@ACDesignsGarage Жыл бұрын

Awesome hope it helps!!! Let me know how it goes!!!

@olesneaker 8 ай бұрын

You are the first welder I have subbed. I like your approach, methods, explanations. This from a retired high school teacher.

@ACDesignsGarage 8 ай бұрын

Thank you very much for the kind words, if you have any requests on videos let me know!!!!

@DVadventures 2 жыл бұрын

Great advice! Thanks

@ACDesignsGarage 2 жыл бұрын

Thank you!!!!!

@flatrat48 Жыл бұрын

Thanks for the tip. Wire speed! Mow I know to put more wire on that thin stuff. Awesome!

@ACDesignsGarage Жыл бұрын

Awesome thanks, good luck on your welding adventures!!!!

@DangrsDave 11 күн бұрын

I use 0.030 and gap. I'm able to use a lower heat and speed setting than I used with 0.023. The thicker wire carries more current allowing lower settings.

@DangrsDave 11 күн бұрын

Also hammer and dollying mig welds might crack the weld. Mig welds are much harder than tig welds.

@Hoaxer51 Жыл бұрын

Great video, Thanks for sharing!

@ACDesignsGarage Жыл бұрын

Thanks for watching!!!!!

@jonathankoros 2 күн бұрын

You said you're using 75/25% gas but were looking at the 100% CO2 chart for your speeds. The 22ga with .023 wire said 1 and 12 for your gas

@50sKid 9 ай бұрын

Thanks a lot for making this video, very helpful

@ACDesignsGarage 9 ай бұрын

Thank you for the support,I hope it helped!!!

@mikebadilla6970 10 ай бұрын

Thanks for teaching us ,I need it.

@ACDesignsGarage 10 ай бұрын

Thank you for the kind words!!!!

@frankfurther3828 Жыл бұрын

Great tips and a good education

@ACDesignsGarage Жыл бұрын

Thank you, hope it helped!!!!!!

@ernestlippard1292 2 жыл бұрын

Really liking the information and techniques you are posting. Thanks a lot! I know you like air tools, but I would like to see flap disk grinding disks for electric 90 degree high speed grinders on your Amazon product lists. I haven’t seen them linked in any of your videos. I like that metal and wire gauge measuring tool too. I’d like to buy them through your Amazon links.

@ACDesignsGarage 2 жыл бұрын

Thank you for supporting my channel, ill try and go put links to several flapper wheels on this video in the description if you want to check back, and thanks again for helping out the channel!!!!

@ClintsStreetMachines 10 ай бұрын

This helped a lot! Thanks for the great video.

@ACDesignsGarage 10 ай бұрын

Awesome, glad it helped!!

@karsbkool Жыл бұрын

Fiber Roloc disc's are awesome for preparing sheet metal for welding. Extra clean with little metal removal

@ACDesignsGarage Жыл бұрын

I love those fiber rolocs

@roryderbyshire4630 Ай бұрын

Awesome mate Cheers Rory

@ACDesignsGarage Ай бұрын

Thank you very much!!!

@leighbratcher1998 8 ай бұрын

Best video for welding thin sheet metal I have seen, and I have watched a bunch. I am working on a 1970 Datsun and the metal is 22 gauge and I have been having a hard time trying to weld. It looks like I have my heat and wire speed too low, will try again tomorrow.

@ACDesignsGarage 7 ай бұрын

Thank you very much ,good luck, remember take your time and keep it cool ,keep your gaps tight as possible and youll do fine!

@rafterL78 Жыл бұрын

Good lesson. Thank you

@ACDesignsGarage Жыл бұрын

Thank you for watching!!!!

@alandust2188 2 жыл бұрын

Thanks, learned a lot.!

@ACDesignsGarage 2 жыл бұрын

Awesome so glad!!!!

@bobrat Жыл бұрын

That Miller is a sweet unit. I'm using 20 ga. It's taking some time to dial it in. I use a paint pen and write the settings on my table. Works 4 me.

@ACDesignsGarage Жыл бұрын

Thank you, yeah I do the same thing, you can look at my table sometimes and see sharpie notes on my welding table lol

@JV-li5jf 5 ай бұрын

Love this, very informative 👍

@ACDesignsGarage 5 ай бұрын

Thanks for watching!!!!

@AMMA-we3zz Жыл бұрын

What I learned from trial and error is to avoid having a gap or just a hair line gap at the most to avoid blowing holes. Both panels will join as the heat will melt them together and where possible, place a large heat sink behind it like Copper or Aluminum. That’s how I managed to weld thin metals. It is a joke some of the replacement aftermarket panels are actually made out of 22 gage steel. I actually had to fabricate my pieces from and 18 gage and sometimes 16 gage steel because 22 gage cannot take the heat and if it did, it gets even thinner when you grind the welds.

@ACDesignsGarage Жыл бұрын

I totally agree, i have blocks of aluminum I like to clamp on, especially when I'm tig welding super thin stuff. A tight fit is key!!!!!

@UnconventionalMetal Жыл бұрын

Thanks for this comparison

@ACDesignsGarage Жыл бұрын

Hope you enjoyed it, thanks for watching

@robertb8280 6 ай бұрын

Thanks for the great video. I have to do a lot of welding on my cars and it is a PIA with the thin metal. I am always playing with the settings trying to get a good weld. BTW, I am sure you know this, but some of your audience may not know that the numbers on the Voltage for the Millermatic are not actual output Volts. The Machine goes from 10 to 23 volts give or take, so the number 1 is probably around 10 volts and 2 is like 12v -14v or something like that. Thanks again for your video, it is really helpful.

@ACDesignsGarage 6 ай бұрын

Thank you, yeah I have trouble with people understanding the ole 1-5 on the voltage side of things, but I find it easier, guess cause im use to it lol. Thanks for watching!!!

@BlueMacGyver 2 жыл бұрын

On 22 gauge you'll get that gap automatically even when its butted up because the heat of the weld is pulling the metal back during the process, but is then covered up immediately by the molten metal.

@ACDesignsGarage 2 жыл бұрын

I agree ,thats why I suggest making it fit as tight as possible because metal shrinks when you weld it, thanks for the comment 👍

@mikemarshall7016 Жыл бұрын

Excellent!

@ACDesignsGarage Жыл бұрын

Thank you for watching!!!!!

@johnnybravo380 3 ай бұрын

Great video!

@ACDesignsGarage 3 ай бұрын

Thank you!!!!

@jimdrechsel3611 8 ай бұрын

I welded heavier materials for years and had to learn the hard way for sheet metal. KZfaq has helped immensely. I like the way you showed how charts on a welder are not the end all but a start. They do help for thicker materials. If you really want to know your penetration and strength do a couple destructive tests like bending back and forth. You can also cut the seam afterwards and see if the weld is solid or has pockets. I think the 2 & 70 setting would cause more heat and distortion. Also degreasing the metal makes a huge difference before welding. Thanks for a great video.

@ACDesignsGarage 8 ай бұрын

Thank you for the comments and the support!!!!

@MidnightOilsRestoration Жыл бұрын

Great job brother

@ACDesignsGarage Жыл бұрын

Thank you very much!!!!!

@darkysnark Жыл бұрын

Excellent tutorial. Thank you. Have 2 old cars needing this now. I'm down to the Yes Welder or the Prime Weld machine. Similar price points. Will be glad to get you review... On these type welds how do you go about prepping for paint/prime?

@ACDesignsGarage Жыл бұрын

Thank you, Im fixin to do a video on how to prep and paint from start to finish soon.I have a yeswelder and did a review on it also have a discount code ACDESIGNS it will save you 10% . Video link below kzfaq.info/get/bejne/eqyYmpyI1pPNeKc.html

@impsquared 9 ай бұрын

thank you for this video! helped me a lot! 🤩🤩🤩🤩🤩🤩🤩🤩

@ACDesignsGarage 9 ай бұрын

Awesome so glad it helped!!!!!!!!

@brentsmith5647 Жыл бұрын

Brilliant video thank u 👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

@ACDesignsGarage Жыл бұрын

Thank you!!!!!

@ironbirdclub9673 5 ай бұрын

Thank you so much

@ACDesignsGarage 5 ай бұрын

Thanks for watching

@tonymaines3837 3 ай бұрын

I have and old Miller 130xp and I set it on 2 and almost 60 it dose about like yours. PS Thanks for all the tips over the years 😃

@ACDesignsGarage 3 ай бұрын

Thank you for your continued support, its greatly appreciated!!!!!

@mpina001 Жыл бұрын

Great video! I now know what I need to do to stop blowing through my late 80’s Nissan. 80’s Japan metal is SO thin. Lol.

@ACDesignsGarage Жыл бұрын

Awesome I hope it helps, I know about that that thin metal, i have a 94 nissan hardbody pickup

@mpina001 Жыл бұрын

@@ACDesignsGarage oh nice! Are these settings good for that thin Nissan metal?

@janeblogs324 Жыл бұрын

Trys 80s land cruisers, metal so thick you can sandblast it without warping

@ACDesignsGarage Жыл бұрын

@@janeblogs324 i love fj's my dad had one years ago.

@BUILTFORDTOUGH79 Жыл бұрын

Thanks for the video. My issue doing cab corners is, I can’t get the Dolley behind to hammer it flat, so it’s SLOW going to try and keep from warping. I like to use compressed air, or in a pinch you can use air duster. I’m not a professional by any means (hence, why I’m watching different videos for techniques).

@ACDesignsGarage Жыл бұрын

I know exactly what your talking about. Those cab corners can be tough. Keep your gaps tight as possible and keep it cool like your doing. That air duster is a great idea!!! The one thing i try to do is cut my cab corners higher so I can hammer my welds and get to them easier.

@BUILTFORDTOUGH79 Жыл бұрын

@@ACDesignsGarage thanks for the advice man, I appreciate it. I’ll try cutting them higher, as the patch panel is oversized and will allow that.

@dannyduncan7407 7 ай бұрын

keep up the good work

@ACDesignsGarage 7 ай бұрын

Thank you for watching!!!!

@chrisl1636 Жыл бұрын

Millermatic 200 manual says to reverse polarity to weld .023 and thin sheet metal , it lowers the heat

@popatop6657 5 ай бұрын

On the gap you need more voltage and less wire speed. Maybe try 2 and 40 to start. Believe it or not the higher wire speed does finely increase voltage as well.

@ACDesignsGarage 5 ай бұрын

Ok thanks ill try that

@danbirch8939 4 ай бұрын

Thanks!

@ACDesignsGarage 4 ай бұрын

Thank you for watching!!!!!

@adamlechmichalak2720 Жыл бұрын

Good video, one minus is the rest of us use the metric system 😀

@ACDesignsGarage Жыл бұрын

Yeah I forgot on this video I usually try to add that info, sorry lol thanks for watchin!!!!!

@sonnyblazer5504 2 жыл бұрын

Your method works best - yes it does!

@ACDesignsGarage 2 жыл бұрын

Thank you!!!!!!

@CoderMan 2 жыл бұрын

Here is a basic question, but i have to ask. How is the working piece grounded? Or is your whole table a ground? Love the video, these tips will help immensely when I get into my car project.

@ACDesignsGarage 2 жыл бұрын

Thanks for the question, my ground clamp is on that plate that im working onand its also on a metal table, I just moved it down so it was out of the way.

@captainkirk1745 10 ай бұрын

Many thanks!

@ACDesignsGarage 10 ай бұрын

Thanks for watching!!!!!

@dunstan06 8 ай бұрын

Best video for me a one week rookie

@ACDesignsGarage 8 ай бұрын

Thank you good luck on your journey, here is a link to my welding playlist, maybe it can help you out there are 27 videos in there I think. kzfaq.info/sun/PLly0wFZ3b0EUfw-y66mVLdVwVd8CsHqgZ&si=ZJ-gjdWzdt2i_oCY

@rodb8274 9 ай бұрын

I’ve given up trying to butt weld 22 ga zinc coated auto body panels. Sure, if you skip around the panel leaving a 1” gap, letting those tacks cool naturally, then doing another round leaving a 1/2” gap, you will have ALMOST no warpage. Great! Now the warpage and shrinkage begins. WELDING CAUSES SHRINKAGE! Connecting ALL the spots has a cumulative effect. I don’t care how cool you keep the panel, the end result is serious warping. You cannot hammer and dolly this crappy metal straight. You also cannot grind the front surface flat without pinholes everywhere. Any paint job will fail! I’m convinced that using Panel Bonding Adhesive using a contour matching backing strip is the way to go. No warpage, super strong bond and waterproof seam!

@robertwilliams8010 Жыл бұрын

Thank you 🙏

@ACDesignsGarage Жыл бұрын

Thank you for watching!!!!!!

@TallStarlite Ай бұрын

What your not able to do, I have no problems doing. What welder are you using? I do just fine with a Lincoln 140 with gas & 0.023 wire for 22 gauge and aim at edge of the metal and puddle jumps over. Then from there I stack down the center. It looks your welder is to Hot for 22 gauge.

@ernestlippard1292 2 жыл бұрын

Saw that you added flap disks to your Amazon account as I requested. Thanks very much. Question: I visited the site and noticed that they also offer 120 grit as well as the 60 and 80 you posted. If I order the 120 grit instead of the 60 or 80 will you still get your credit with them since I came through your site, or must the product be specifically linked to the link you posted. I'll still get the 80 grit if it must be specifically linked, but I prefer the 120 grit. Thanks again for putting yourself on You Tube. It is very generous and big hearted of you to take the time to offer your skills and experience to the world with no promise of any return. God bless you, brother!

@ACDesignsGarage 2 жыл бұрын

Thank you very much for the kind words and support. If you click on the link thats in the description of my video first then you can search for what ever grit you want and ill get credit. Thank you again for the support!!! Its nice to hear some kind words instead of a bunch of trolls lol, Have a Blessed day God Bless Adrian at AC Designs Garage 🙏

@MattTheCameraGuy 2 жыл бұрын

Love watching the grassroots of welding! Brought me back to my days working for Don Jacks at Street Metal Fab.

@ACDesignsGarage 2 жыл бұрын

Thanks man, that is my mission I want to share what I've learned over the past 15 years building hotrods.

@dirtyjobs3995 2 жыл бұрын

Great tutorial, what is the abrasion material on the air sander you used to prep / clean the metal?

@ACDesignsGarage 2 жыл бұрын

Thank you very much ,Its 80 grit sand paper

@flyermike2029 Жыл бұрын

Thanks, this helps a lot. How did you ground when you were stitching? Did you just put the clamp on the table and that was good enough? Forgive me, I’m new doing this so I’m trying to learn.

@ACDesignsGarage Жыл бұрын

No problem, yeah its grounded to the table, if the part was bigger id just clamp to the part. Thanks for the kind words, if you have any questions just let me know!!!!!

@melgross 9 ай бұрын

You see that 20 ga is as low as you can go with co2. That’s understandable. It’s a reactive gas and really even 20 ga is a bit thin for that. Yeah, co2 is cheap, but causes embrittlement and weaker welds. The thinner the material, the worse it is. You, like most of us, use 75/25 so 22 ga is fine. Also using .023 or .024 wire (with the right diameter liner, roller and tips!) helps a lot with really thin work.

@ACDesignsGarage 9 ай бұрын

Thanks for the tips!!!

@andrewbrown1463 Жыл бұрын

Great video. I’m doing the same thing but using FCAW. Lincoln 140 machine. I am on the lowest voltage and very slow feed speed. To prevent blow thru this is best approach right? I’m welding in a rocker panel patch with 22ga.

@ACDesignsGarage Жыл бұрын

I haven't messed much with FCAW. I just bought some fluxcore wire to try to do a video on sheet metal to see if I could help you guys out that wasnt runnin gas. Id say get some scrap and mess around with settings. Try your low setting and add more wire ,sometimes when you introduce more wire it cools the weld. Try to increase in small increments till you get the best results. Super short tacs as fast as you can may help. Make sure to subscribe and ill see if I can get a video out soon. Let me know how it goes!!!!

@Anonymous-um3im 9 ай бұрын

Quick question. Sorry if it’s dumb, but when tack welding do you start on one side and drag the melted metal to the other side or do you just weld right in the center of both sheets of metal. I was told not to tack weld right in center because it could burn through but these tack welds look perfectly centered. Thanks

@ACDesignsGarage 9 ай бұрын

There are no dumb questions, thats how you get better. You can tac it in the center like I did on this video if your fit up is prety tight. If you have a decent size gap you'll have to start on one side and wash over. Its no biggie if you blow through, just keep tacin till you fill the hole. Thanks for the question!!!!!!

@Anonymous-um3im 9 ай бұрын

@@ACDesignsGarage thank you !

@frankfurther3828 7 ай бұрын

Watching again, I can have access to some 20g sheets, If i get great at those, I'll be great at 18g.

@ACDesignsGarage 7 ай бұрын

Your right, the 18 will be a walk in the park!!!!

@BigggA608 Жыл бұрын

What worked for me is instead of starting from the top I begin about an inch and a half away from the bottom tack. Run my weld to the bottom then begin above that about inch and a half away from where I started my last weld so the weld heat can dissipate away from the area where my next weld will end. I really hope I explained that correctly. Hope it helps someone out and great video brother.

@ACDesignsGarage Жыл бұрын

Thanks for the tip, ill try that, always lookin to improve!!!!

@floridamanfishing1390 3 ай бұрын

Can you use the same method on floor pans? I have an 85 Chevy Camaro. That the driver's side floor PAN is pretty bad and I do have the PAN ready to go in. Never done it before. But I do have a welder going to give it a go

@ACDesignsGarage 3 ай бұрын

Oh yeah you should be good. Just do a little practice piece to set up your welder to make sure you have good penetration!!!! Thanks for watching!!!!

@stuartbird5217 Жыл бұрын

Great video, and great accent 👍

@ACDesignsGarage Жыл бұрын

Thank you very much, and thanks for watching!!!!!!

@claytonreed7489 7 ай бұрын

Thank you for the information, question if you are welding like a roof how long do you weld? should you move around? and last should you you use air to cool your wels??

@ACDesignsGarage 7 ай бұрын

I move around and cool between each tac to keep distortion down. Thanks for watching!!!!!

@SwedesGarage Жыл бұрын

I just learned something about wire feed, thanks. But I have a bigger problem, on the car I'm working on the sheet metal from manufactor was 22 gauge. But when they put that 22 gauge in a big press to form the floor board, fender etc, the metal stretches and gets even thinner. Now I'm trying to weld it and it just burnes a hole because the metal is so much thinner than the orginial 22 gauge. You got any tips and trix? Thanks.

@ACDesignsGarage Жыл бұрын

Thank you, sometimes you can cut up your wire feed a lil more can help with blowing through. Find you some scrap 22ga. And play around with your settings ,turning them up and down till you find your sweet spot. Hope this helps, and thanks for watching!!!!

@fordfalcontimetraveler4523 Жыл бұрын

Good information. Thanks. I have a cheep HF Tools 120v Flux core wire welder. Can you do some videos on a 120 v welder?

@ACDesignsGarage Жыл бұрын

Thank you, yeah i have a 120 240 yeswelder. Im gonna try to do a flux core on sheet metal soon.

@rtkracht 2 жыл бұрын

If you ever use flux core wire… I’d like you to do a similar comparison. I’m not sure it’s even possible to get decent results. Just wanted to get your opinion.

@ACDesignsGarage 2 жыл бұрын

Im no good at flux core, I make a big ole mess with it, it maybe possible but no with me lol ,try it out and let me know how you do!!!

@dakotamax2 Жыл бұрын

Any recommendations for an online source for practice sheet metal? Also, would be interested to see a demo on welding a piece of sheet metal to a thicker piece of bar stock (fillet and butt joints).

@ACDesignsGarage Жыл бұрын

weldmetalsonline.com/ these guys have an awesome selection. I hope this helps!!!!

@madandhami7535 5 ай бұрын

Nice 👍

@ACDesignsGarage 5 ай бұрын

Thank you!!!!!

@bushpilot73 Жыл бұрын

the quarter panel patch panel I need to do...I can't get behind it to dolly it after I weld it. How do I fix the warping that you beat out in this situation? Excellent video, thank you for sharing!

@ACDesignsGarage Жыл бұрын

Thank you!!! Those are kinda tricky, there is 2 ways that I do them. First is to weld very slowly and cool after every tac and take your time fitting your patch as perfect as you can. The other method is if you can cut the brace out thats in your way till you get your patch welded in and hammered out ,then weld the brace back in. Just becareful that it's not structural , ive done this on front fenders alot, hope this helps!!!!

@bushpilot73 Жыл бұрын

@@ACDesignsGarage Thank you, that gives me two options. 🙂

@ACDesignsGarage Жыл бұрын

@@bushpilot73 hope it helps!!!!

@jamescurnutt1628 8 ай бұрын

My Chevelle got hit by a drunk driver on Christmas Eve last year. Not super bad, but needs some welding on the rear 1/4 panel skin. I have been dealing with burn through with the exact same machine. I thought my wire was coming out too fast on the lowest feed setting. I was doing the opposite. Also need thinner wire. I have been using .035. Got so frustrated, I went and bought a tig welder.

@ACDesignsGarage 7 ай бұрын

Glad you're OK. Keep your gap tight as possible and take your time and cool it and last but not least get 0.030 or 0.023 wire if you can and youll do fine. Thanks for watching!!!

@MidnightOilsRestoration Жыл бұрын

I do a lot of restoration work also and it requires a lot of patience for certain. I've never done very much tig welding to be honest although I would like to become proficient in it; years ago most of the type of welding we are doing (restoration work)was done with oxy-acetylene followed by hammer welding to prevent cracking. What's your opinion on what is best for this type of work all around?

@ACDesignsGarage Жыл бұрын

Thanks for watching, I like the tig process over mig on sheetmetal repair because you can hammer weld it. Mig will crack for sure if you over hammer it because its so hard. I think the the tig process is very simular to oxy fuel welding. If you can oxy fuel youll have no trouble tigging it.

@MidnightOilsRestoration Жыл бұрын

@@ACDesignsGarage that's really interesting, I bet it leaves some really nice looking seams! I will have to invest in a tig unit.

@fishenbyfaithoutdoors2589 Жыл бұрын

Welding two pieces of 18 g end to end. What does the other side look like after mug weld? Thanks ahead.

@ACDesignsGarage Жыл бұрын

If your heat settings are right you should have 100% penetration. Do you some practice pannels and mess with your settings till you get the results you like.

@mxgregg3544 2 ай бұрын

Can you weld continually on thin gauge or like you do in the video small spot welds?

@ACDesignsGarage 2 ай бұрын

You need to do the small spots to keep the temperature down so it doesnt warp as much.

@gene2200 7 ай бұрын

Dont sell those small Miller's anymore, had mine stole. Got a Lincoln 140 I've gotta dial in this week, not an inverter, old heavy copper type so shouldn't be to different i hope. Always used .030 any smaller and i blew holes. Think i usually set it at 2 and 60, was the 110v 70amp.

@ACDesignsGarage 7 ай бұрын

Yeah thats what id start with, good luck!!!!

@TheGoldinge Жыл бұрын

What you did on the speed, like 1/50 or the 2/70 can you do that on a lincoln welder?

@ACDesignsGarage Жыл бұрын

You should be able to, the easy way is to go to your chart on your welder and set it up to the recommendation then tune it in up or down with some practice pieces. Hope this helps!!

@justinmichealduncan1055 Жыл бұрын

If i had to do a weld test if i had to weld that thin type of metal onto a flate plate is it ok to mig using that stitch type style of welding?

@ACDesignsGarage Жыл бұрын

If it were a welding test id say maybe not, really depends on what there looking for. And also it really depends on the thickness of the thinnest material. If it were 16 ga. Id say just straight weld it but thinner than that its gonna be tough not stich welding it..But as for sheet metal on body pannel and floor pans id say go for it.

@NoMonkeyBizz Жыл бұрын

I have a millermatic 140 i was welding a 22g made holes my set for 22g speed auto & gas 200.what the issue? My wire 030

@ACDesignsGarage Жыл бұрын

22ga is tough, the thing that helped me the most is fit up, try to have no gap if you can, you want it tight as you can possibly get it and keep it cooled. Get some scrap and play with your settings. Thats how I do it.

@andrewglagau8685 Жыл бұрын

Hi, I'm not very good at mig welding. Just starting out. My wife just bought me one today and it's a gasless mig welder. I'm currently working with 1mm thick square 40 X 40mm tubing but been practicing on some scrap metal I picked up from my metal steel supplier. I seem to burn holes if I try to mig scrap. What am I doing wrong? Should I be turning voltage down?

@ACDesignsGarage Жыл бұрын

If you want email me some pics and ill try to see what maybe the problem. The flux core welding can be tough, im thinking about doing a how to video on it and give it a shot. Here is my email acdesigns1933@gmail.com

@GodofAbraham Жыл бұрын

1 mm is difficult with flux core things you can try that should help use more angle on your gun welding at a 45-degree angle increases penetration and heat use that and work backwards and leave more wire stick out about an inch it will preheat the wire that's how I do it I hope this helps good luck.