How to modify a Minn Kota powerdrive V2 control board to adapt to the older powerdrive v1 version

No video

How to modify a Minn Kota powerdrive V2 control board to adapt to the older powerdrive v1 version

Рет қаралды 22,440

Күн бұрын

This video describes how to modify a Minn Kota powerdrive V2 control board to adapt to the older version V1 powerdrive without changing out any additional components

Пікірлер: 61

@jimholtse928 Ай бұрын

I had a controller go bad on my v1 24v powerdrive. I spliced in a v2 control to the v1 board. Works good, even my autopilot works.

@nickgiallo7597 Ай бұрын

@@jimholtse928 you are welcome

@grinderk533 3 жыл бұрын

Did this to my version 1 watching this video, worked great! Good idea to keep new plug in circuit incase old foot pedal goes bad.👍

@nickgiallo7597 3 жыл бұрын

you are welcomed

@ANMTCUP 4 жыл бұрын

Thank you Nick, today following your video I changed my control board for $200 dollars US. a big savings

@nickgiallo7597 4 жыл бұрын

Your welcome I like to helping others

@2wheelwhit Жыл бұрын

Thank you very much, this worked on my power drive v1. Back up and fishing

@nickgiallo7597 Жыл бұрын

You are welcome

@nickgiallo7597 Жыл бұрын

Always trying to help us fisherman

@poormanselectronicsbench2021 2 жыл бұрын

Good info, thank you for sharing! I would be interested in changing that controller board on the motor, AND, updating to it's matching newer foot pedal as well (which is still readily available as of 2022) It would also save the step of changing foot pedal connectors to the controller. I battle with the original pedal due to its control locations, the newer style makes more sense to function for me.

@donaldgilbert2718 2 жыл бұрын

Very helpfull, run at 100%, save hundreds of $$$

@nickgiallo7597 2 жыл бұрын

thank you that was my objective

@danman8417 5 ай бұрын

what gauge tiny wires are on that new v2 board

@Robinjaha 3 жыл бұрын

Does this model of minn kota have the I pilot ? Im searching for a wiring diagram for the Powerdrive V2 between the sensor board and the control board. Btw good video!

@stunter4everfsls 4 жыл бұрын

my wiring was a bit different. the yellow, white, brown, black, red, etc.... coming out of the spiral cord from the head of the motor didn't get plugged in at all. they were just left inside the center section just unplugged from anything. as my v2 board didn't even have the corresponding wires coming out of the board. everything still worked as normal. so strange. did I do something wrong? or order the wrong board? im assuming those wires are for the autopilot. EDIT I just realized that I ordered the board for v1 W/O autopilot. MAKE SURE TO ORDER THE CORRECT BOARD

@tbirdslot69 2 жыл бұрын

Solder and shrink tubing would make a cleaner install

@danman8417 2 ай бұрын

Anyone try a V2 board in old white top Powerdrives 765mxt circa 1999?

@GusgusA1 3 жыл бұрын

So this is an update to be able to use V2 foot pedal? then in oder to upgrade to ipilot you need to update the head unit? Would you have a part number for this?

@craigrogaczewski8485 4 жыл бұрын

This looks like it would allow the installation of the I Drive system on the older version of the Powerdrive motors? Am I thinking correctly?

@nickgiallo7597 4 жыл бұрын

Yes that is correct

@maxboltmanjr364 3 жыл бұрын

If river does he mean I pilot?

@stephendouris3441 3 жыл бұрын

Thank you for this info my power drive board does not have a number on it it has faded out so how can I be sure of fit

@nickgiallo7597 3 жыл бұрын

You best bet is the Minikona web site

@bpihead 5 жыл бұрын

so is it the caps that dry out to cause the failure? If so why doesn't minn kota design them for replacability?

@mrdiscotoyou 4 жыл бұрын

I've had the steering go out on several autopilot boards. The culprit is usually a transistor. They used 2 each, TIP41 and TIP42, to create the H-bridge that allows the steering motor to be driven both directions. If autopilot only corrects 1 direction, it is likely that one of those transistors has failed. I have replaced the faulty component on one of my boards, but haven't patched the potting or put it back in service.

@sagestrickland8131 2 жыл бұрын

@@mrdiscotoyou i had one to go out so replaced the steering motor switch with a window switch out of a 1994 chevy truck and ran the prop motor through a 12 volt speed controller off e bay for around $12.00 , that is a cheep fix but it works . i later found a used board off a newer like the video . i replaced it like the video

@bontayoglife4322 4 жыл бұрын

my minni kota is not working I think the board is bad. where I can buy the board

@MrWhiltetail Жыл бұрын

I was hoping to see how to get the dang cover off that houses the controller without breaking anything but you didn't disassembly or reassembly. Bummer!

@TubLis01 3 жыл бұрын

Could I in theory, use a v2 pedal for pd1 control board with this concept by just swapping the pedals female plug?

@nickgiallo7597 3 жыл бұрын

I think it should work

@TubLis01 3 жыл бұрын

@@nickgiallo7597 I think I’ll try it and keep both plugs to see if I can swap between v1 and v2 like you did except for the pedal

@TubLis01 3 жыл бұрын

Update, pedal contacts are laid out differently. V2s have 6 wires where v1s have 7, I had to update my control board and just use the v2 pedal as is. Also, tip, if you decide to update your control board to use the newer foot pedals, make sure you are purchasing the correct one for your motor. Either with or without autopilot, I made the mistake of buying the one with auto when I didn’t have a yellow/green wire to connect. Was able to exchange but just wanted to let you folks know! Happy fishing!

@BottledUpFunk 3 жыл бұрын

@@TubLis01 Did you install the board with auto pilot to see if it worked even though your head didn't have AP?

@TubLis01 3 жыл бұрын

@@BottledUpFunk I initially bought the autopilot control board by mistake and had to return it because the wiring from the head unit is different. The auto pilot control board has additional wires (green and yellow) that won’t work with the non-ap version head unit.

@guitarman8025 2 жыл бұрын

I have a v1 minn kota power drive without the pilot system,flat plug, do you think the new board will work using the existing pedal?

@nickgiallo7597 2 жыл бұрын

Yes it should

@nickgiallo7597 2 жыл бұрын

Just wire it back

@mulespur4806 4 жыл бұрын

Everyone says that the v1 is analog and the V2 is digital. In theory the motors don't know it's either one. But the copilot is V1 analog it's kind a strange it is talking to digital V2 control board??? Everyone is working for Minn Kota that is saying this apparently.

@nickgiallo7597 4 жыл бұрын

My working great 👍

@brittlinton8764 3 жыл бұрын

I got ripped off on a auto pilot v2 the foot control doesn't work and he didn't have the remote he told me its cheap to buy another remote well its not blue toothso this is my final option im praying it works.

@williamchildress1459 2 жыл бұрын

So you just change out the plug for the foot control also?

@nickgiallo7597 2 жыл бұрын

No I kept it

@williamchildress1459 2 жыл бұрын

If I want to use the foot control of my V 1 I will have to change is that correct?

@stevemurphy3554 4 жыл бұрын

Did the foot pedal still work didn’t show mines a 2001 auto pilot would this board still work

@nickgiallo7597 4 жыл бұрын

Yes it does for both

@stevemurphy3554 4 жыл бұрын

Nick Giallo great I have the board came today I’m going to hook it up like you did just in case foot pedal is bad but sure it’s the board thanks again. I’ll let you know

@williamchildress1459 2 жыл бұрын

Will this work on a 24 volt Minn Kota trolling motor?

@nickgiallo7597 2 жыл бұрын

Not sure