No video
How to modify an RC prop to fit a minn kota trolling motor
Рет қаралды 2,389
Күн бұрынHey all, as of now there are limited props APC makes that directly fit a trolling motor, so in this video I show you how to make almost any RC prop fit a minn kota trolling motor (55lb or below). NOTE : for Minn Kota make sure you order a pusher prop.... so that way you're not going into reverse when you choose a forward speed. I've ordered some props and as soon as I get them in and look them over and test them, I'll put them below, I dont want to miss lead any of you into purchasing a prop that I know won't work for you.... as of now, the only prop I know that works well for both the 55lb and 30lb is the 10X5M-LH here is a link to it. I've received a few props in today and a few were very flimsy....
www.apcprop.co...
I'm working with APC to put this prop on Amazon for easier ordering (and a little $ in my associates acct..lol)
Hope this video helps you
@balam8743 2 ай бұрын
Drilling the prop this way will make the prop unbalanced. By with a regular drill will make the hole no longer precisely center as manufactured therefore it will cause vibration. It will work but I'm sure the vibration is there. You might not feel it but it's there. The correct way to drill the pro and keep the hole centered is to have it lathe mill or professionally drilled by a machine shop.
@codyakfishing8856 2 ай бұрын
I agree, this was mainly just for fun, and as light as these props are, I don't think it be much of an issue
@Piratepeteoo 7 ай бұрын
Hi I'm doing a 11 X 7 inch ,,,,3 blade propeller on a,,,,,,, watersnake 34LB thrust,,,,now I'm in the process fitting the propeller I've also added a rudder now I need some ,,,, stainless steel clamps ,,,,and then for the shear pin I filed the shear pin slot ,,,,well that was okay a small round file dose the trick worked out fine
@VirtuActive 3 ай бұрын
So what's the prop you ultimately think best for 55lb-86lb thrust motors? *My sisuation's a bit different. I'll be using one 55lb and one 86lb trolling motor (vevor and newport) on my 27 foot sailboat. The sailboat runs great off a 4hp gas motor, so i suspect it'll do just fine with this combo. But want to make sure to get the right props for the job. So which size prop ended up working out best for you?
@codyakfishing8856 3 ай бұрын
My best performing one so far is the 10X5m-LH
@robertjanbout1437 24 күн бұрын
You know apc made special trolling props?
@codyakfishing8856 21 күн бұрын
Yea I know, but I wanted to try out different pitches and lengths
@namo80 23 күн бұрын
Hey. Can't find this prop in Europe. Just the shipment cost almost 30 usd. How did it go with APC, did you guys develop a prop without having to drill? Best regards from Sweden
@codyakfishing8856 23 күн бұрын
I have one to test but haven't gotten an chance, as of now I highly recommend the 10X5m-lh prop for 30-55lb motors, works great and is made for trolling motors so it's already drilled out
@namo80 23 күн бұрын
@@codyakfishing8856 Thanks for the quick reply! I really hope they get those in the European Amazon. Otherwise I'll have to pay import taxes etc. Would be cheaper for me to get the original prop 😅 I'll keep a eye out for your next review!
@codyakfishing8856 23 күн бұрын
@@namo80 that may be a while down the road, I haven't even registered the boat yet, I'm thinking of doing the review on the kayak
@diveflyfish 7 ай бұрын
For a 55lb Minn Kota, what is the Amp Draw difference between the 10-5 vs 10-7? Is the speed difference appreciable enough to justify the higher current? Do you find the lower pitch 10-5 more efficient than the stock OEM prop? Thank you for your work and video! Cheers
@codyakfishing8856 7 ай бұрын
I have a video on it ... Look in my channel for APC prop vs stock prop
@diveflyfish 7 ай бұрын
Thanks!
@SaltWaterBassTv 10 ай бұрын
I have a older saltwater min kota 40lb thrust was wonderingbwhat size u reccomend
@codyakfishing8856 10 ай бұрын
I would recommend the 10X5m-lh, worked great for both my 30 and 55lb thrust
@SaltWaterBassTv 10 ай бұрын
@codyakfishing8856 what a fast reply! Bless you and your channel! Shall I expect to modify all of them or not the marine ones?
@codyakfishing8856 10 ай бұрын
@@SaltWaterBassTv no the 10X5m-LH should be a direct fit, as long as the shaft is 3/8 in diameter, and thanks, I wanted to head out today to test some more props but there's a bug going around and I can't shake it....lol
@SaltWaterBassTv 10 ай бұрын
Why do this if there's ones that are a direct fit?
@codyakfishing8856 10 ай бұрын
This is mainly for those who want to try different diameters and pitch, since there's only a few that are a direct fit as of now
EVERYTHING cpo (@Vaarticus; @go.fast.r)
Рет қаралды 123 М.
Spilt Milt Productions
Рет қаралды 39 М.
Codyakfishing
Рет қаралды 150 М.
South Georgia Bassin
Рет қаралды 4,3 М.