BEST MILWAUKEE TOOL Wet/Dry Vacuum (M18 VS PACKOUT FUEL) kzfaq.info/get/bejne/aK6Fd7Ghx5uuqqs.html

Even when you mess up a sentence, you never stutter, you just slow down and think of a word or words that fits best and you keep on going acting like you meant to say every word you spoke. That's a sign of a master talker.

Great vid! I was in the Air Force many moons ago and worked on the flight-line. I got out in 86. I always liked how our tools were fitted in to foam just like the Kaizen foam today. I think they used a hot wire tool to do it back then. The organization had the purpose of lowering the amount of fod (foreign object damage) done to an aircraft engine, and it also helped to keep your tools organized. Since getting out, I have always wanted to do this with my tools, and I have to admit, the Kaizen foam makes it easy.

For finger holes I've heard you can use a piece of copper pipe held with some pliers/grips and heated at the other end, then you can melt vertical (or whatever angle you want) holes to whatever depth and diameter (use whatever diameter pipe fits your fingers) you want.

You did it again Vinnie! That was super slick! Thanks! 👍😉

From Canada. I have a packout and the foam is a bit expensive so I just use a thicker carpet. Works pretty decent. They move around but are still protected a bit. Love the videos.

I did this with my dewalt case thing i had laying around. Milwaukee tools in a dewalt case lol.

I must have watched the Beginning 100 Times I could not stop laughing watching Vince pop out like Super Hero Ready to save the Day

Sweet vid. Have an idea that I've used in the past.. cannot take the credit as learned it from a kaizen event. Trace and out cut with the razor through a few layers leaving tools a little proud. Wrap tools in aluminum foil. Lightly heat area with heat gun and place wrapped tools to desired depth. It perfectly fits tools. Either way awesome vid. Thank you.

Dudes like a freaking cartoon character I love it!!!! Lol great vid Vince

Love the slow rise entrance! Thanks for sharing some great tips for using the kaizen foam. I bought a 2.25" x2' x 4' sheet from Rockler for $25 so I can do a couple of Packout boxes.

If you have the depth in your box, make the hole for your chargers (or any tools with cords) a little deeper. You can stash the cords under the tool, no cord mess. And like said before, keep a thin layer of foam for the lid. Otherwise, good video for "shadowing" tools.

Love these foam videos Vince! I watched a ton of videos and picked up some tricks in addition to yours. 1. Use a torch on your hole saw before drilling for a clean edge. Also, using a torch on a 1/2" copper pipe will make a great finger pull. Keep up the videos!

Valuable information. Thank you for the great work 👍👍👍👍👍👍👍👍😊

That intro though... 😎👌

Like it! Great tips, having the foam in there is great so the tools don’t roll around. 😊

Great video. Thank you for this channel. It’s been helpful. I spent everyday in December looking at all the deals lol. Drove my wife crazy.

Great video Vince!!! Hot soldering iron...I never would’ve thought it! Can’t thank you enough for all your suggestions! VCG totally rocks!!! You’re all awesome, entertaining and informative! You look after your viewers and I hope your viewers are appreciative like I am!!! Also on another note, Vince you and the Mrs( DYNAMIC DUO) is must see TV for me on the weekends! You both complement each other wonderfully and it’s so enjoyable to watch it weekly and I can’t thank you again! I have said it numerous times and I’ll keep saying it that a major channels to pick you guys up because your videos are amazing!I hope you have a great week!!!

I’m definitely doing thins with my m12 set. dope video Vince

Good evening, VCG and all the gang! 👍🧰👍

Great video thank u gentlemen 👍

Great tips on better tool storage👍I small flat square tool bag with clip which I can hang up, I have clips for spanners or screwdrivers, with small bottle of lube like small sauce bottle, tread tapes. This save weight having carrying big bag or going back up n down get tools. Magnetic tray is good have if you up high.

It doesn’t matter if your a carpenter, plumber, electrician or HVAC we love our tools. I just subscribed over a week ago you guys have a great KZfaq channel👍

Another Awesome Video!!!

It's Sooooo easy.... a Carve Man could do it.

Vin, what a great video thank you for sharing!!

Great video vince love the channel

Thank you VCG

Hey there Vince, could it be done to the rolling cart inserting foam, that's my go to tool box and I need to secure my finish nailer gun, gen 3 hammer drill, impact driver, grinder, and circular saw wit four batteries and charger..Thanks!

Yessssss!

Great tip great vid👍👍

Kaizen makes some great inserts and paired with packout it’s amazing. But unfortunately for my trade I just use the packout bag and throw my tools in. My load out constantly changes. Thanks for the video guys.

Vince another great foam fitting video...! 👍

if you heat the holesaw up a bit it should seal the foam and stop the small bits of foam from braking off when you take your chukes in and out .Great video .

Hanks Vince, I firmly believe that the lid should have a thin layer of foam. Doing so sill have tools fully incased in foam for the absolute best protection.

Your vids are awesome!!!!!!! I have watched a lot of them. Keep doing what your doing and I will soon also join. God bless you all!!

Vince what do you do to store your consumables ( bolts ,screws, some of them are up to 5 inches long ) in. I was looking at a packout box. What do you do with pat boxes from one job to the next..

VGC Construction I liked and Subscribed for the Liberty Bell

Very nice organization tool box 👍

Great video Vince very informative thanks for your tips and tricks

Always liking those tips and tricks

#200 to hit the LIKE BUTTON !!! LOL I guess I'm slowing down a bit.🤩😄 Thanks again for sharing your thoughts and videos Rodney

Great video! Always learning something new on your channel!

Fantastic video as always Vince. @VCG Construction has lots of good ideas. I wish someone, maybe Milwaukee even, would sell a packet of templates that were the right size and shape of various tools. That way you could use them to layout the foam and not have to trace around the tools. Seems simple enough - they know what each tool shape is. Maybe not every tool they sell, but all the common ones you would put in a packout box.

Instead of trying to clean the sharpie markings away, try spraying a coat of black plasti dip over the foam. It helps to hide the jagged cuts and makes it look like the foam molds around the tools.

You can use your half inch or 3/4 hole saw as well to make rounded finger holes by each opening.

Cool

Kaizen inserts also sells precut foam inserts for every different storage box you can possible own for anyone that hasnt heard of them. They make the foam storage process a walk in the park. So easy a caveman can do it!!

Very cool vince

Great tips, I love your videos much luv from Detroit 👍

Great tips!

Great video. Wondering if you can use the oscillating multitool for cutouts as well? Hot iron would work too, but with the smell :(

Awsome work

The nation of organization.🙌🏽

Can’t wait for the drawers.

I made a seat that attaches to the packout system that I love, does that count?

Good Job! Very nice! Thank you! Like Button...Done.

Have you tried spraying your insert after you're done with a rubber coating like flex seal?

Nice tips brotha!!!

I love the Kaizen foam, it makes it very easy to spot if a tool is missing ... Now I just have to wait for the foam to come on special here in Canada. At this moment I find it is still a little expensive.

Great video !

HEY VINCE " DAS A NICE" Mr prince of power tools

Worksite organizational bliss. Coin that.

About how deep down do I need to go to fit m12 drill, impact,and impact wrench ,

Looks like we have FUEL model Vince back 👌🏽

Great video

Hi Guys!!! Awesome work Vince/Nick! You guys are clicking good lately on the video work. Hey Vince, could you do a video on how you organize your other Packout boxes such as the small/large/rolling boxes especially with hand tools? I've been going back-n-forth on which box is the best for hand tools, etc.

So funny that this vid dropped today. For Xmas, my Family went “click happy” & ordered 6 each of 20mm, 30mm, & 57mm 2’x4’ sheets of Kaizen Foam from Fastcap; cuz I kept saying I wanted to organize my Packout tool boxes & organizers a lot better & make them, functional, lol. So, w/ all the Kaizen Foam I have & all my tools out & everything.....it’s kind of overwhelming a little. Like, where to begin & start making it look so pretty inside😅. Do gotta say that VCG is awesome, w/ the tool storage vids using Kaizen Foam, the Very Cool Gang; for helping ppl w/ tips, tricks, projects, etc...& bounce ideas off another person. Also gotta thank those ppl who helped me out w/ customizing my Kaizen Foam for my storage needs & not being judgmental at all, & taking their time to really help out, especially w/ all the questions, lol. Not every community would be so kind & “offering”; but the Very Cool Gang is such a Family & that’s great 👍🏻 It’s really nice to know that help is out there, just have to not be afraid AND ask for it. Thanks EVERYONE, & VCG😊 Cheers✌🏼

Great video start 😂 play the avengers end game song for the first few seconds would be perfect!

How much is the foam cutouts for the Milwaukee pack out boxes?

Aye Vince big fan of your channel and Milwaukee products, just bought the 3 piece pack out set at Home Depot, it didn’t include the foam, where can I get that thick/layered foam? I tried their Northern tools in Walmar, any suggestions?

Nah bro, I watched this video to hit that like button. 😎

Nooice!

Vince, I’d throw a layer of foam under the lid and cut down the bottom piece underneath, that way the tops of the tools aren’t hitting the lid plastic and rubbing, and anything heavy on top is less likely to squish the tools. This way, the tools are completely encompassed in foam for full protection!

Out of the Box Thinking

I like .... and you right... is more better... LOL

Chaulk marker works well so you don’t have to worry about leaving marks if you’re ocd.

Can you do a video or suggestions for a larger rolling tool chest like a dewalt tough chest ?

I am going to pull the trigger on the Pack out next time it's on sale

Like your channel Good jod

vcg home depot has M18 FUEL 18-Volt Lithium-Ion Brushless Cordless Combo Kit (4-Tool) with Two 5.0 Ah Batteries & PACKOUT Rolling Tool Box for $399

Very nice and neat for someone who has plenty of boxes or not many tools but when you do this think of all the expensive wasted space. If you did this for most of your tools wouldn't you have to buy dozens of cases? Doesnt the packet protect your tools even without the foam?

Glad you got your voice back bro

Well now I know how to do it, but I just need to get motivated to do it.

Are the foam inserts sold separately?

Why not cut out an extra area under the charger for it's cord to go under it? Is that box deep enough that you could put the charger in on it's side and maybe make a second slot to put in a bit set such as the 48-32-4009, which would cover a huge chunk of your drilling and driving needs. Speaking of driving needs, I never took a real look at that installation tool before, I saw it quick and was thinking it was a homeowners type tool. But, seeing as you had one, I decided to take a closer look. What an ingenious, little creation that is! May need to add one of those to my system.

Hey Vince, where are you getting your large sheets of foam?

Impressive how much you were able to fit in there

How do you get tid of thr black sharper print now.

I use the soldering iron method for my pew pew box.

I like it but there is too much wasted space. There is an entire layer of foam underneath the tools that is doing dick all. Does Milwaukee make a shallow box for these situations? Great video guys.

I clicked the video because I love their content too much. I only own a drill.

can we just heat the power tool so it will melt right through the foam?

Another tip when cutting inserts make a half circle on each side for fingers to get in beside the tool.

Recommend fastening one thin layer of foam to the inside of tool box top for better cushioning.

if you want to get those holes even cleaner spin the heole dozer and put a flame to it to get it warm not hot before u drill and it will finish the outside of the hole cleaner

@VCG Construction if you take the tools out, grab a rag, spray some Windex on the rag and lightly scrub the Kaizen. The sharpie will easily come off the Kaizen.

Can’t wait till DeWalt 2.0 tough system rolls out!!

Another tip is to attach some Kaizen foam with double sided tape or glue to the top of the lid to compress down on your tools to better hold them in place.

could you also put a layer thats below on top so its not marked?