How to Paint a Flat Panel Door

How to Paint a Flat Panel Door | 3 Easy Steps

Рет қаралды 98,946

Күн бұрын

Jeremy demonstrates how to paint a flat panel door, using rollers in three easy to follow steps.
Timestamps:
0:00 Introduction
0:37 Supplies
1:08 Preparation
2:45 1st Coat
10:21 2nd Coat
11:14 Cleanup
12:08 Conclusion

Пікірлер: 125

@debbieallen4918 6 ай бұрын

This was really good and I needed to know everything you suggested as mostly watching would be amateurs. Thank you, by the way I love your response to the negative post😊

@SuperVassarBrothers 6 ай бұрын

I’m glad it was helpful! Thanks for watching and for commenting! I wish you well in your door painting endeavors 🫡

@GabRock91 Ай бұрын

This is exactly how it should be done. Anyone saying you should take off the door clearly doesn't get that as a professional painter, you pretty much won't get paint on the hardware. Plus its a lot easier and faster to paint while the doors hung, you get to do the whole thing without having any drips or finger marks afterwards.

@SuperVassarBrothers Ай бұрын

The finger marks afterwards is a big consideration that most folks don’t think about. Also, if there’s a lot of doors, you often don’t have the space to stack them against the walls. Leave them hung and remove the door knobs if you feel like it. This is the way 🫡

@sheribeaudin979 6 ай бұрын

Thank you for the video! We have solid wood doors that were a very dark stain. I painted them white, but did not prime first. What a huge mistake! So now I have to do it over. So I'm assuming I sand a bit, prime and paint again correct? I've heard to do a light sand in between coats to get a really smooth finish Is that necessary? Thank you!

@SuperVassarBrothers 6 ай бұрын

If you continue to get bleed through on your doors then you’re probably going to need to prime with something like BIN shellac. That’s what we use when we convert stained trim and doors to painted. You can sand between coats if the finish feels rough. Just don’t sand after the last coat (obviously). Here’s a video on BIN in case you end up heading in that direction: kzfaq.info/get/bejne/g76qpJlhvJyrpKc.htmlsi=4s0NqobeA5FXtgNA

@yordanpopov Жыл бұрын

I have the same color for the doors. Do you know which Sherwin color it matches to?

@SuperVassarBrothers Жыл бұрын

We used Sherwin Williams Extra White 7006

@Beyondspotlessauto 9 ай бұрын

Hi, Did you think the paint at all or just straight out of the can?, same approach for trim as well?

@SuperVassarBrothers 9 ай бұрын

I don’t think we strained it. It was a new can and wasn’t chunky. Trim is a little different cause we don’t typically use a roller for any trim work

@user-oh7jc8mb7h Жыл бұрын

Appreciate the video. Came trying to see if we could paint doors while hung. We painted one side of each door twice (after having someone hang them), and didn’t want to pull them again to do the other side. 1: plenty for a newbie 2: never thought the door behind was messed up 3: why paint the top? Seems like a waste of time (suggested by someone else). Hoping our SW emerald comes out as good. Appreciate you. Oh and F the douches that just have to complain about something.

@SuperVassarBrothers Жыл бұрын

Haha, folks always something to complain about. Just part of the deal of posting videos.

@douglasshackett8747 2 жыл бұрын

Don't forget to dust the top of the door and around the door knob, the roller will grab loose particles and deposit them in your paint job.

@SuperVassarBrothers 2 жыл бұрын

Spot on Mr. Hackett

@geoffreymeare3406 Жыл бұрын

You should paint the top of the door.

@pearlperlitavenegas2023 2 жыл бұрын

Door looks beautiful what paint is this? Do you recommend Emerald urethane for doors? ProClassic?

@SuperVassarBrothers 2 жыл бұрын

Thanks Pearl. Its Duration semi gloss from Sherwin Williams. We like Emerald urethane as well. ProClassic not so much. :)

@larrywatson499 2 ай бұрын

Pro classic, hybrid is great paint. Duration sucks on trim

@angelayu7550 Жыл бұрын

If the door, trim and cabinets were previously painted with semi-gloss would it need to be sanded and primed before the new color goes on? Thank you.

@SuperVassarBrothers Жыл бұрын

You shouldn't need to prime unless the previous trim paint was oil and you're going over it with a latex. It's not a bad idea to sand it a bit so that the new paint sticks a bit easier, but if you're going over latex you should be good to go. You can check out this video I did on priming different surfaces: kzfaq.info/get/bejne/o6uFjcSJttbcYps.html

@user-oh7jc8mb7h Жыл бұрын

@SuperVassarBrothers Жыл бұрын

I’m glad it was helpful! Painting the top can be a good idea for an exterior door. It just helps the door stay sealed if it wasn’t done from the factory. I don’t know many folks that paint the top for interior doors.

@ghrohrs2020 10 ай бұрын

Just make sure to do a light brushing across the top with an unloaded brush to avoid any ridges that affect closure.

@jennifermcnuttmusic6353 9 ай бұрын

Great video! Ugh. Trying to fix to slight marks on beautiful door similar to this one. Guy at Sherwin-Williams told me to use a foam roller and it turned out like crap. I’m moving and it’s my friends door so I’m going to sand down the one panel, maybe the whole thing and do your process. I’ve painted a ton but not these really smooth doors. Should I just use 150 grit or something else then 150?

@SuperVassarBrothers 9 ай бұрын

Use 150 grit and I wouldn’t use a foam roller. Try a 1/4 inch white nap roller cover and I’d got with emerald urethane, regular emerald semi-gloss or duration semi-gloss. Good luck!

@UndercoverRat 7 ай бұрын

did you apply primer to the door before painting? thanks.

@SuperVassarBrothers 7 ай бұрын

Nope. These doors were previously painted with a latex based paint so there’s no need to prime.

@jeffdana9402 Жыл бұрын

Great channel for professionals. Nothing here for a beginner. Moving on ....

@SuperVassarBrothers Жыл бұрын

You might find some things useful if you punch around a bit more in our content. A lot of folks have found our series on painting a bedroom helpful. Gotta start somewhere

@traitaothomusa-dangcaumong2664 8 ай бұрын

please u teach me how to say in english for buy the white liquid to paint the door? i am renting condo apt here door is too old want to paint make it look new. please help me out. thanks. just open and pain or have to mix with things else before can go paint on the door ? please help me.

@SuperVassarBrothers 8 ай бұрын

I'd recommend going to a paint store and explaining what you're trying to paint. They should be able to assist you with finding a product that would work and will mix it for you. Good luck with your project!

@UndercoverRat 7 ай бұрын

I painted my door with a microfiber roller. The finish came out perfectly apart from the little fibers that stuck to the door. How do I prevent this when painting subsequent doors please? I used acrylic enamel paint,

@SuperVassarBrothers 7 ай бұрын

You can use a piece of painters tape and use it to go over the surface area of a new roller cover. That will remove the majority of the loose fibers that usually get stuck in the paint.

@johnjohn-ne8fw 10 ай бұрын

Curious. Why not just use the 4 inch roller on the toe and heal? Good video 👍

@SuperVassarBrothers 10 ай бұрын

You can if you've removed the hardware. I find it easier to use a brush to get around the hinges and so forth.

@chriscortopassi9289 9 ай бұрын

If you painted the whole door with just a brush (no rollers) would it leave brush marks?

@SuperVassarBrothers 9 ай бұрын

For sure it would. I’ve got a series of videos coming out about how to brush doors. I brush doors that have a grain to them and we usually roll the doors that don’t.

@gianthills Жыл бұрын

Do you ever spray? Seems it's a big selling point for the speed, but the cleaning and the masking time. I can see it for industrial jobs or exterior fences or garage doors, but interior doesn't make much sense to me.

@SuperVassarBrothers Жыл бұрын

We are primarily a brush and roller crew. We use to do more spraying, but we got away from that type of work cause I don't like doing it 😬. We mostly paint in fully furnished homes, so spraying isn't practical on most of our jobs. There are a lot of crews that spray almost everything and they get super fast at prepping everything and spraying, but that's just not our jam.

@heathermiller5580 4 ай бұрын

Hi, I just moved the door knob on a bifold closet door from the side to the center. I Patch the hole and now I need to paint that area on the door. Any tips?

@SuperVassarBrothers 4 ай бұрын

If you have the same paint that was used before then you may be able to paint the strip of the door that the patch is on. If you’re using a new paint then I’d recommend painting the whole door (at least the side that faces out from the closet)

@heathermiller5580 4 ай бұрын

@@SuperVassarBrothers it's factory white so I have no clue what " color" to use

@paulkolm8225 4 ай бұрын

Another excellent video. I am going to be painting that exact door style except it's new pre-primed molded panel solid core. I am using BM Advance and plan to use your technique shown in this video but I noticed when I painted pre-primed mdf baseboards that the first coat of advance really soaks in fast and it gets tacky very quickly causing deep brush marks no matter how fast I try to get it on and leave a wet edge. Overlap areas are nearly impossible to avoid. The smooth finish is more important to me on the door than the baseboards so I was wondering if it would be better to re-prime the pre-primed door before painting with advance. Paint color is Simply White in Pearl finish if that make a difference. Thanks in advance for your advice.

@SuperVassarBrothers 4 ай бұрын

I don't think priming the doors will make that much of a difference. I'd recommend doing 2 coats. You can sand between coats to keep things smooth, but the second coat will be the most important. You'll have to figure out a method that'll work for your application process and your speed. The paint will definitely flow more smoothly on coat #2.

@unasistent 6 ай бұрын

Do i need to apply any undercoating product before paint?

@SuperVassarBrothers 6 ай бұрын

You don’t need to prime if the door has previously been painted with a latex based paint. If the door was previously painted with an oil based product then you may need to prime with a bonding / adhesion primer.

@unasistent 6 ай бұрын

Is a new build house ..was 3 years ago😅..but no idea what sort of paint they used

@ivpu2465 2 жыл бұрын

When do you make the other side?

@SuperVassarBrothers 2 жыл бұрын

Hi Iv. We painted it soon after we painted the first side. Its the same process and thought it would be repetitive if we showed it again.

@ivpu2465 2 жыл бұрын

@@SuperVassarBrothers have tought yo have done it. It would be maybe good next time to show in time laps for 5-10 seconds "the other side goes the same". Great video, it will help me in my next peoject😉

@cubeweaver 8 ай бұрын

I used roller with semigloss paint and it left roller marks. Semigloss drove me crazy!

@SuperVassarBrothers 8 ай бұрын

It can be a bit tricky avoiding lap marks but you can get better at it the more you do it.

@darrenharris2978 4 ай бұрын

Is trim paint same color as the door sir

@SuperVassarBrothers 4 ай бұрын

Most of the time it is. Sometimes people paint the doors an accent color like black and the rest of the trim is white.

@xbadandy182x 9 ай бұрын

I practiced rolling on one of my doors and it came out super textured. I didnt like it, so i sand it down completely flat with 180 grit and finished with 220. Re tried again and rolled it... once it again supet textured. I cant figure out how to get it smooth when rolling. 😢

@SuperVassarBrothers 9 ай бұрын

You may be having an issue with the type of roller you’re using. I prefer 1/4 inch nap woven rollers for rolling doors. That’ll give you as smooth a finish as you can get from a roller and that’s what I was using in this video.

@brianleiby6723 9 сағат бұрын

@@SuperVassarBrothers I have the texture problem as well. Also, I used 1/4 inch nap woven roller. So its got to be something else like paint quality.

@amonratpeavy9717 11 күн бұрын

🙏 ❤❤❤

@SuperVassarBrothers 11 күн бұрын

🫡

@amritraisingh 11 ай бұрын

Make video how you wash your paint brush after using semi gloss paint

@SuperVassarBrothers 11 ай бұрын

How To Properly Clean a Paint Brush kzfaq.info/get/bejne/npiEnNZ3razJXWg.html

@FryingPanFarm 3 ай бұрын

Wouldn't you advise cleaning the door first? and does not the whole thing need to be sanded a little to take off the shine? Thanks!

@SuperVassarBrothers 3 ай бұрын

Depends on the door. The house we were in for the filming of this was exceptionally clean. You can sand if the door has an aggressive shine to it or if it has a rough finish that needs to be smoothed. The paints we use have excellent adhesion, so we don’t generally run into issues with it bonding to a surface that’s been previously painted with latex.

@FryingPanFarm 3 ай бұрын

Awesome thanks bro. You mostly using Duration nowadays? @@SuperVassarBrothers

@UndercoverRat 7 ай бұрын

how do you avoid streaks?

@SuperVassarBrothers 7 ай бұрын

Part of it is experience / skill. That being said, you just want to pay attention as you’re laying down the product that you’re not leaving lap marks / streaks. Smooth them out as you see them with the roller.

@joshjohnson3352 3 ай бұрын

Even easier is getting a tampon roller and rolling the whole door minus the edges and back brush. You can push it in them corners better than with a 4 in roller

@SuperVassarBrothers 3 ай бұрын

We’ve been using those a lot recently too. I am a fan, and you’re right, you can get them in the corners better than the 4 inch variety 🫡

@donaldsincennes9673 Жыл бұрын

Friendly tip! WOW! All this to paint a door? Why not work out of the paint tray? Correct, start with the heel. I would suggest you put more paint on your brush. All you need to paint a door is TSP, sanding sponge, a 6'' fabric whizz roller and a 2'' quality paint brush. That door would normally take 2 min to paint. The gooseneck guy! Cheers!

@SuperVassarBrothers Жыл бұрын

Sounds like you got it nailed.

@alanwilkinson9487 Ай бұрын

Did you use water based paint.?

@SuperVassarBrothers Ай бұрын

I believe we were using Emerald Urethane Trim enamel which is a hybrid trim paint. It’s technically waterborne but has oil resins pumped into it to give it some of the desirable characteristics of an oil based paint.

@alanwilkinson9487 Ай бұрын

@@SuperVassarBrothers reason I asked is that it looked like it went very easily, unlike oil based... Thank you..

@masterciefl2k Жыл бұрын

Naps what material?

@SuperVassarBrothers Жыл бұрын

Pretty sure those Sherwin Williams rollers are 1/4 inch woven nylon

@Thesheriff1776 2 жыл бұрын

Would you recommend priming first if the door was shoddily painted a green color by an instagram wanna be previous owner? 🙃

@SuperVassarBrothers 2 жыл бұрын

Yes, priming would be great especially if they were an instagram wanna be. :)

@GODfirst165 9 ай бұрын

😂😂😂

@rsturbo4018 Ай бұрын

My door frame is down to wood. How do I do that?

@SuperVassarBrothers Ай бұрын

You can prime it with a primer like Fresh Start from Benjamin Moore then coat it with whatever trim paint you prefer 🫡

@rsturbo4018 Ай бұрын

@@SuperVassarBrothers Ok brilliant thank you

@georgecantu8040 5 күн бұрын

Is this water base or oil base ?

@SuperVassarBrothers 5 күн бұрын

We were using a latex (water) base paint in this video. There are very few oil trim paints still in use

@purpletrance9874 4 ай бұрын

No sanding of the whole door to ensure a good key for the new paint? 🤔

@SuperVassarBrothers 4 ай бұрын

Pretty sure we scuff sanded the door prior to painting. We’ll sand in between coats if needed. Sometimes we don’t show everything in the videos

@thatlittlehomestead 6 ай бұрын

No primer is needed?

@SuperVassarBrothers 6 ай бұрын

Nope. The door was previously painted with a latex based paint so we can go straight over it.

@armodularkitchenajayakumar8461 Жыл бұрын

👍👌

@SuperVassarBrothers Жыл бұрын

Thanks for watching!

@antonyreed8281 Жыл бұрын

take a look at the glass door in the background . lol😁

@SuperVassarBrothers Жыл бұрын

Those glass doors are new and have plastic covering the glass. After you finish painting them you cut the plastic out with a razor blade. lol 😉

@antonyreed8281 Жыл бұрын

@@SuperVassarBrothers I feel reassured and can now take you serious. lol

@DAMON409 4 күн бұрын

You first give it a light sanding, and not just around the edges.why multiple rollers? You could have rolled the whole door with the 9" using very little paint. You are using semigloss, which means all rolling has to be in one direction. You are rolling the top of the door horizontally. Incorrect.

@SuperVassarBrothers 3 күн бұрын

Sweet dude. Appreciate the insight

@HeyJoe1978 2 жыл бұрын

Take the door off and remove all hardware.

@5150STL 2 жыл бұрын

I've done the paint it hung and cover the hinges before but totally confused why the latch wasn't removed as it's two screws.

@nothingsimpostleble1593 2 жыл бұрын

Joe Nobody Does that bro it's too much

@number1pappy 2 жыл бұрын

I've inquired about this as well and was told some owners don't want doors removed. Weird ,I know as I would definitely request doors removed and especially all the hardware. There is nothing worse than overspray or painted over hardware! It just screams shoddy work in my opinion.

@SuperVassarBrothers 2 жыл бұрын

Hi Joe. Taking the door off and removing the hardware is a good option. For most our jobs it's more efficient to paint while the door is up. Also we are precise and don't get paint on the hardware. On the rare occasion we do, we would scrape it off.

@SuperVassarBrothers 2 жыл бұрын

Hi Robert. Sometimes we do remove the latch. In most cases we don't because but its easy to paint around and when we instal the door handle its always in the exact location it was before. We've had some bad latches break, or not go back in the same spot and we spent half an hour trying to get the door handle to work because the latch was crappy. More of a risk reward situation for us since time is money. Thanks for your feedback.

@MAGAMAN 4 ай бұрын

Wasted a lot of time by not removing the latch or taping over all the hinges. It only takes seconds to tape a hinge

@SuperVassarBrothers 4 ай бұрын

Sweet deal. We do both depending on the job

@stevecam724 Жыл бұрын

Love the shit paint job on the glass behind him, paint everywhere 😂😂😂😂😂

@SuperVassarBrothers Жыл бұрын

Those were new doors with plastic on the glass. You cut the plastic off after you paint them. That’s how you do it. But I appreciate the ignorant and insulting comment. 💩

@stevecam724 Жыл бұрын

@@SuperVassarBrothers 😂😂😂😂😂 triggered dude 👍👍

@simpletonballsack 9 ай бұрын

@@stevecam724 You are an absolute dik, Steve. Namaste 🙏

@haakonsteindal8042 7 ай бұрын

@@stevecam724 Stop being a child and pay attention, maybe you will learn something...

@stevemarklewin6500 Ай бұрын

Amateur brushing the brush down over edges will sure create a lip of paint. You should brush up over the upper edges and down over the lower edges 🙈🙈

@SuperVassarBrothers Ай бұрын

Mmmkay, but I rolled into the wet cuts which created a uniform finish. There were no lips of paint on this door when it was finished

@johng9562 8 ай бұрын

Spraying is vastly superior if you know what you are doing. BTW only amateurs use tape rather than removing all of the hardware, which is faster, easier, and better AKA the Trifecta of the right way. Don't bother responding....

@SuperVassarBrothers 8 ай бұрын

Thanks for your gracious observations. A lot of our audience are DIYers, so it’s unlikely they’ll be using an airless sprayer. A lot of the ways I demonstrate things on the channel are geared in that direction (like taping hinges). To your other points, even as professionals, there are many instances where removing all the hardware and spraying would be impractical (like if you were painting one door). And I’ll respond if I want to good sir. Enjoy your evening 😘

@popeyerugby77 6 ай бұрын

@goofy-aaahhhgoober 4 ай бұрын

@King_drew 3 ай бұрын

Your comment is arrogant and senseless. My proof is you feeling good about saying, "Don't respond". 🤡.. The replies to your comment have more appreciation (likes) than yours. Smh

@joshjohnson3352 3 ай бұрын

This is easier if you just have a few doors to do rather than breaking out the sprayer

@zee9er 2 ай бұрын

No prime?

@SuperVassarBrothers 2 ай бұрын

Nope. We were painting over builder’s grade latex so there’s no need to prime. Scuff sand and you’re ready to rip. (I’m not sure if we showed the scuff sand in the video. This was from a while ago)

@davidf1985 6 ай бұрын

How is the door a flat panel ? It has a recessed design.

@SuperVassarBrothers 6 ай бұрын

I could be wrong, but on job sites I've always heard of these non-grained patterned doors as flat panel doors. I suppose you could call them paneled doors, it's just how I've heard the term used in common usage.

@klynch7329 3 ай бұрын

I work in door and window sales. Flat, or more accurately, smooth panel is correct, as this is a paneled door without a fake woodgrain texture. A door without panels is also called a flat slab door and can be either smooth or textured. A bit confusing, but builders, carpenters and painters are familiar with interchanging terms. Hope this helps. Great painting tips, by the way.