everyone is crying I didn’t use adhesion promoter so check that out

the valve on the can is what gets clogged and fails. You just soak the nozzle in mineral spirits but don’t leave it in too long it will dissolve the glue and blow it apart

Never put a needle in the nozzle cause it will mess up the fan pattern. The way you keep the sputtering is to heat your paint up but soaking in hot water or set on the defroster in your vehicle. Then shake the can really well.....when you are done shaking.....shake it some more. Then after a minute of spraying shake your can some more.

***PRO TIP*** Use one or two drops of either a 3 in 1 oil or some sort of oil meant for lubricating fan motors and bearings. Probably any oil that isn’t too thick will work. Drops go straight into the male or female output hole on the spray can. Place cap back on and spray it in the air or on scrap for a second or two to blow out any excess oil in the cap. Paint will no longer clog or stick inside the cap and you should have a smooth spraying experience for the duration of your project 🤫

Will that work on vinyl?

@@Sip28 Yes. I painted my dash pad with it.

How has it held up over time?

@@josephbrisco1826 No problems as of this moment.

What's different about it? ​@@superfuntime3107

jeeps have half doors

no

study adhesion promoters.. no. I have never clear coated them

@@chriscraft77022 awesome thanks, I don’t know much about painting outside of homes lol!

i had to respray them.. I have a video duplicolor vs color bond.., after recoat they stayed perfect to this day

Did you watch the video? Because if you did, you'd know he sprinkled it, then wet it.

🤡 you will if you ever try

what are you spraying? I have never had that happen

@@chriscraft77022 The door panels to my 1987 Dodge Dakota. I had washed them down with water, then used a bathroom scrub with bleach to scrub the surface in order to make it clean then I had washed it off again. After it dried I scratched it and the paint just comes off like acrylic paint. Also I used the same paint in this video

@@NumberedK. you must of used a soap with something in it that made the paint stick to whatever is in the soap.. i have sprayed carpets to seats.. everything with this stuff an i have never had it flake off... i have even used it as paint to match interior parts over metal parts.. i have never even had it rub off over years on a steering wheel color change.. the surface of the panels was not prepped right.. thats all i have to say..

@@chriscraft77022 Dang it, for sure thanks. Any possible ways of fixing it? Is there a clear coat or something I can add to make it un-scratchable?

no

I have steering wheels I painted 20 years ago that haven’t even rubbed the color off yet.. just wash them twice with bleach soap.. people think I make this shit up for my videos... smh

@@chriscraft77022 your good thats why i ask, just to be sure before i go and do my own

im about to do a video using color bond ( expensive brand) and see how that works out.. people spray interiors with armor all then don’t get it all off before trying to paint .. then the paint just flakes off

yeah, but it leaves it stiff ...test it first

When you spray fabric when the paint dries take a stiff brush to brush the fabric down. Then spray again and brush again. Also vacuum after brushing.

thank you tip expert

I would never sand plastic

no way don’t even try that

I scuff mine down with a gray scotch pad.

NO... paint cures.. why would you think that? paint does not leave a smell.. if it does you did something wrong and are having a chemical reaction

Oh cool thanks no i was just wondering cause u know how regular spray paint smells

@@GsFoxbody oil based paint smells.. cause it takes forever to cure.. like rustoleum..

I have not used rustoleum interior paint.. is it good?

@@chriscraft77022 all of thier paint is head and shoulders above the rest. The only time I buy another brand is if I cant find it in rustoleum