UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzfaq.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

You should have changed the pump oil. Its non-detergent 30W oil. And no you cannot overfill the regular oil in the engine, if its spilling out the top its full, and will continue to spill until its level with the opening. This isnt a lawn mower engine where overfilling will cause it to smoke. Also, use 10w-30 or straight 30 engine oil.

I can't thank you enough for this Video. Before watching this Video I didn't know where to start to change the Engine Oil, Air Filter, Pump Non Detergent Oil or to even put in the Pump Saver. I bought a used 3800psi Power Boss Pressure Washer at the Pawn Shop and I followed your instructions. I watched your Video several times, thank you again and God Bless you.

For a revised version of this video in the future, I would suggest showing how to replace the pump inlet filter and also changing the pump oil (15W40 in mine).

Thanks a lot for taking your time and making a great video.

Nice overview. Thanks for making!

Thanks for the info. I own a small business and do not need a big bill for fixing a pressure washer because I was too lazy to tune it up!

Very helpful guide, thank you very much. You are AWESOME !!!

THANK YOU,VERY INFORMATIVE!

Wow thank you. Very helpful

Excellent! Thanks!

Good job. Thank you....

great video, thanks.

Great job

Great video

Thank you Sir✊🏼

Very helpful.

I think there was another drain screw on the other side of the pressure washer that had a down hole to catch the oil on the pan. Lol but great job made it look EASY and Messy :) thanks for the overall instructions.

Woah your the man!!! Thank you for this my pressure washer is shutting down on me and I don’t know why

Very helpful, thanks. I will check out your other videos since I'm a new owner of a gas pressure washer. I don't even know if the water has to be completely drained each time of use.

always great to leave debris and garbage that falls off the OLD air filter and just plunk the new one on top of the garbage. niiiiiice

was the gap checked before threading the new spark plug? Out of the box, I've had spark plug gaps be way off.

amazing video, thank you

Nice video👏👏👏👏

Great video. Thanks for sharing. New subscriber here

Thanks very much

nice thank you

Can I do the same steps for John Deere ac2700. And I don’t have the manual for you didn’t explain or showed the oil type and where the best place to buy if you can advise me. Thanks great video though

Thanks for the info and tips im smashing my like botton kaboooooooooooooom

Great video, thanks!

Thanks my friend is good.

What do you guys use for your O-ring lubricant??

How often do you do an oil change and spark plug filter

What about the oil in the pump housing?

nice video

I see you changed the engine oil. What about the pump oil? Should that be changed or checked regularly? I have the 3300psi Simpson

THX FOR YOYR VIDEO. PLEASE DISREGARD NEGATIVE COMMENTS...

spark plug should have had gap checked prior to installation, old plug should have been looked at for how clean it was burning, pump oil should have been checked at the least or drained and replaced. air filter base should have been cleaned prior to new filter installation. draining engine oil, engine should have been tipped slightly to remove as much old oil and you can. this is was more of a SERVICE than a tune up but it was a sloppy service at that

You just put the new air filter down on top of dirt

I think you should pull the engine cord while adding the pump saver to make sure each valve assemble gets some.

How often do we have to change the spark plug?

Thanx man

Is the pump saver good in freezing temperatures?

hey I subscribe! do you have a video on how to change the carburetor? if you do can you send link please. thanks

What oil do you use for winter use?

Where to start... 1. Change the oil hot, with the pressure washer tilted toward the side of the engine that the plug is being removed from. 2. You can change the plug once the engine has cooled, making sure the gap is exactly what the manufacturer (in this case Honda), specifies. It doesn't hurt to spray a little WD-40 on the threads before installing the plug. 3. When you change the air filter, it makes sense to wipe off the housing base/blowing compressed air (with engine intake covered) to ensure the housing area is perfectly clean. (Homeboy here seems to leave a leaf or a moth sitting on the base, and just puts a new filter right on...) Honda wants you to check the oil level by "not threading" the dipstick plug, but rather-resting it on the top thread...good grief. 4. How about changing the pump oil?

It was a decent video, give it a rest people, it educated me. I have almost the same washer and it froze out, now i know to use the pump saver for the winter storage

What about the top side back knob that says Oil close to the water inlet side? Does oil goes in there too and what kind?

Love this new generation. No pride in their work.

Can you show us how to change the pump oil. Thanks. Great informational advice

Tanks

Are you supposed to replace the crush washer or can you re use it?

how do you change the oil in the water pump?

Great

What about the pump oil?

I really enjoyed your video, I saw someone once say that when storing it for the winter that you should put a little oil in the hole where the spark plug does. How do you feel about that

you should always tilt it over while draining the oil....

I have seen enough after the first Minute.

What brand of motor oil did you use

How do you clean the carburetor?

Drain oil on my equipment like that...Fired!

What oil in the engine? Sae 10w-30 ?

Get an oil drain tube attachment. You'll thank yourself every time you change the oil. Completely mess free.

Every how many hours of use will an oil change be required on pressure washers ???...

great video. what's a pump saver?

How often should one do this maintenance

When should you change the oil?

What type of oil should i put in a 2gpi machine gas powered

Is the pump saver can only used for "winterizing", i.e. storing it in cold temperatures or does it HAVE to be used when storing it for any extended period of time, even if inside?

What is the pump cleaner called?

What about the pump oil? Do we need to replace the oil?

How do you get the tires off

when do i use the pump saver?

Where can I get a new air filter?

Dang... u need to pressure wash the pressure washer after spilling all that excess oil.........

A cross thread is tight thread

So he is changing the air filter without clearing/cleaning the dirt on the bottom? Is this clean up or tune up? Tuning is different I thought.

All the mechanic's are criticizing, but here watching to see how to do the work.

W in oil stands for winter, not weight.

What is the gap on that spark plug boss?

why unplug the sparkplug? my engine take like 6 pulls or more to get started there is no risk of it accidentally starting when doing a oil change.

I have to use one just like this but you left out service of the pump. What kind of oil does it use and how to change it

What about actual pump maintenance. Not just the motor. For example, troubleshooting or add/changing the oil.

Do you recommend using 10w 30 oil or 15w 30?

What about being all the debris out that was underneath the air filter!

you need to open the oil fill cap when you drain the oil from the bottom, otherwise the oil will not drain completely

this guy started wrong all wrong ' 1 you don't use wretched to start spark plug ,2 he never show u or make sure the plug electron gap is adjusted , 3 remove the air filter and not clean the filter canister, 4 messy oil change ,5 did not flush out gas tank and make sure the gas tank fuel line screen is cleaned

"Finger-tight." [Uses ratchet and socket] "Finger-tight." [Uses wrench] You keep using that phrase...I do not think it means what you think it means.

You never changed the oil on the water pressure motor, or take out the spring and you also didn't clean out the screen on the water inlet where the hose hooks up. Thank you for the tune up info on the Honda motor though

Russo, do you know what the valve gaps are supposed to be on this particular engine? I can’t find it online and no longer have the correct literature to tell me. Thank you in advance.

no compressor oil change?

Hello ! I wanted to ask something, I just bought a 3200 psi power wash, how often should I change the oil and get a tune up? And is there anything else I should be doing to maintain it? Thanks a lot

You said nothing about changing the pump oil ??

Merci Canada

Check the oil level as it’s overflowing hahahahahaahha

Before I put in a new or replace a used spark plug. I check the gap. You should too

I just tuned up two pressure washers this morning. You never gapped the plug unless you did that off camera. I find that prepped plugs are RARELY gapped correctly so you should have pointed out gapping them or at least checking the gap.

How can that engine start without pulling?

Don’t forget your cup🎉

Why is water coming out of my pressure hose with nothing attached? No wand, no ball valve??? It worked fine yesterday.