how to program ET 500 Gate Motor

Рет қаралды 52,430

Күн бұрын

In this episode, we go through The runtime setup, autoclose and crawl distance setup.
Channel sponsors:-
Rsec Security Equipment Center
www.rsec.co.za
/ rsecequipmentcentre
/ rsecsecurity
Music:- One Thing - Roa (No Copyright Music)
Metro - Yung Logos (No Copyright Music)
Link to Products
rsec.co.za/product/et-nice-50...
Please comment, like, share and subscribe to the channel
Follow me on Instagram:- @Nicks_nd_Tricks
Follow me on Facebook:- / nicksandtricks

Пікірлер: 181

@BornAdventures Жыл бұрын

Thank you so much for this video. You saved me a huge headache.

@nicksandtrickssa Жыл бұрын

Thank you for your comment, no worries, glad it helped, a sub and like would be great

@jeromekiley7750 Жыл бұрын

Great video! Helped me solve my gate problem in 10 minutes!

@nicksandtrickssa Жыл бұрын

Thank you for the comment and glad it helped

@FlyByR10T 2 жыл бұрын

Good video! No one else shows this as well as you do.

@nicksandtrickssa 2 жыл бұрын

Would you like to see more of these?

@vasilioskelaris89 Жыл бұрын

You are a legend! Thanks for all the great advice!!

@nicksandtrickssa Жыл бұрын

Good day Vasilios, well done, great news.

@robertlevendal5741 Жыл бұрын

Hi. Please lower the volume of the music that's playing or better no music at all. I can hardly hear you explaining cause the music is overpowering your voice. Thanx. Ps Great work and training. Keep it up!!!

@nicksandtrickssa Жыл бұрын

Hi Robert, hopefully it will be better on the next 1.

@deonliberator8953 Жыл бұрын

Thanks for the video

@nicksandtrickssa Жыл бұрын

@@deonliberator8953 Thank you for the Comment Deon

@nicksandtrickssa 6 ай бұрын

Hey Robert, a bit long but please check the updated Video kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@_Inevitability_ 9 ай бұрын

This video was so helpful in getting the gate at my new place working again! Thank You!! Can I please ask... Any idea why the manual release would be extremely difficult. I turn the key and then I have to pull with real force, then when it does release the gate even moves a bit... Maybe like 5cm. I tried removing the top screw and putting some oil into the gearbox hole but I only had a big funnel so I made more of a mess than actually getting oil in 🤦🏽‍♂️

@nicksandtrickssa 9 ай бұрын

Thank you for the comment, there could be just be some much by the pin at the end of the door making the pin difficult to push in when you open the door, it's normally a sign of oil getting out. You should not need to ever put oil in the motor but if it's leaking you can top up, the repair process is to replace the base, which can be purchased as a whole, the manufacturer does not service the base any longer and replaces the unit as a whole, if that is the only issue with the motor I would leave it alone until you can have it repaired and depending on the age maybe even replace the inner motor at the same time

@joedaniel2792 2 ай бұрын

Thanks dude

@nicksandtrickssa 2 ай бұрын

Thank you for the comment

@elisharhode92 Жыл бұрын

Hi, thank you for the great video. I want to set my gate limit to shorter than than the actual rail/runway distance. My gate is old with no sensors. When it is running the limit settings I try to manually stop it at the distance i want but it gives a couple of beeps and then wont run back to the closed position to complete the setting. Please advise if you can

@nicksandtrickssa Жыл бұрын

Thank you for the comment Elisha, on an Et motor especially the et500 motor, the limita is the most important part in the system, the gate will not stop until it reaches those magnet limits, even after the setup is complete, you can purchase the limits seperate. If your in the Cape Town area, pop in at Rsec Security Equipment Center. They will sell you a limit actuator kit

@elisharhode92 Жыл бұрын

@@nicksandtrickssa Thanks for the response and guidance

@ZeroKool128 Жыл бұрын

Good Morning. May you please assist me when you have a moment. I need guidance. I have a ET 500 12V Domestic Sliding Gate Motor . Since Eskom load shedding got worst, my gate suddenly don't want to open and i have to manually open and close which is frustrating as i have to watch the dogs when coming out and closing the gate. When i press the button to open, it just beeps 3 times and open for 2 seconds then stops. When i manually open it and close the lock cover, then i press the button, the the gate closes but EXTREMELY SLOW . Can you guide me to may reset it to close normally again please. Awaiting you soonest response.

@nicksandtrickssa Жыл бұрын

Hi Blaize, the 3 beeps is an indicator that the the motor has no AC power going to the board. Please check bottom left, next to the relays if the AC led is on on the board. If not you have to check the 16VAC transformer, it might be blown. That will also cause the battery to be dead and the gate to not open or close fully. If you need any further assistance, feel free to email me technical@rsec.co.za

@nadiahugo9654 5 ай бұрын

Thanks for the videos, usually this works, but today, after doing the first few steps, of locking gate in middle, placing the 'rubber' on the two pins to set in programme mode. Gate closes first but there the simple just doesn't not set. There are multiple beeps. Have tried a few times now. Any advise?

@nicksandtrickssa 5 ай бұрын

Thank you for the comment, if 15 beeps is motor fault, but it can be a sticky relay on the board, if you turn the motor wires around to make it open first, check if it moves, if not then the relay faulty

@nadiahugo9654 5 ай бұрын

@@nicksandtrickssa thanks will try that

@nolanmichaels2766 Жыл бұрын

Hi,my gate upon setting the limits opens fisrt,therefore I need to chance my motor ways around as told by you,can you please explain how it needs to be done as I believe my gate in the close position,is open according to the PCB,therefore shortening my crawl distance wound be done properly or am I'm getting it wrong,please advise,Thanks again for the helpful video and information

@nicksandtrickssa Жыл бұрын

Thank you for the comment Nolan, there is 2x motor wires, blue and black. Connected to motor + and - switch them around, ie the blue and black wires.

@portoesautomocambique4076 Жыл бұрын

Hi. Great video. Would you please help me with my motor? I've programmed the limits sets and learn remote but after all it only open just a little bit for pedestrians and not for TRG full open as I learn remote.

@nicksandtrickssa Жыл бұрын

Thank you for the comment, when you press the set button, does the gate do the same? There is a pot next to the white and brown wires on the board, turn it clockwise all the way and try again. If the problem persist then you have to turn your focus on the gate.

@portoesautomocambique4076 Жыл бұрын

@@nicksandtrickssa Thank you for a your help, I'll try that as soon as I get home.

@zalisile Жыл бұрын

I have the same problem, my gate only opens pedestrain mode. I don't know how to make it open all the way. I also tried your suggestion and it didn't work

@nicksandtrickssa Жыл бұрын

@@zalisile hi, please check the sensitivity pod next to the RX led, make sure to turn it to the right. If the gate always stops at the same place and you have replaced the battery, the gate wheels could be your problem. If you have an alarm system, take the alarm battery and see if the gate goes past the pedestrian point this time. If yes, please get a new battery.

@Deanowp 2 ай бұрын

Please assist once i open my gate it opens than its starts crawling very slow alomst at full open how do i remve the crawling on my gate must i jst reset the limits like in the video its an et 500

@nicksandtrickssa 2 ай бұрын

In the closed position, put the 4 dip switch to on, put the Progj jumper on, press set button 1x, the gate will pause but then open and close, it will buzz when complete, remove Progj, turn dip switch 4 to off. The crawl distance will be less ne, you cannot turn it off

@ashraafmohamed5177 4 ай бұрын

Hi, why would the gate nit close while programming a new dc500 control card.

@nicksandtrickssa 4 ай бұрын

Thank you for the comment, turn the force dial clockwise, gearbox or inner motor could be going

@Mido66778899 Жыл бұрын

Hey nick, hoping you can help, I have replaced the battery but since doing so the gate does not open or close beeps sometime but otherwise I just see the st led blinking, also the moss 13+ led is red any advice?

@nicksandtrickssa Жыл бұрын

Thank you for the comment Mido, how many beeps do u get, if it just beeps for however long you hold the button it might be holiday locked

@Mido66778899 Жыл бұрын

@@nicksandtrickssa how do I remove the holiday lock?

@nicksandtrickssa Жыл бұрын

Where the wires go, there is 3 different connector blocks, the motor side, left, the AC side, middle and the right hand side, with aux and common, remove the 8 pin You will see written, com and Ped Take a screwdriver and carefully touch com and Ped for 5-8second, the card should beep, then you done

@vasilioskelaris89 Жыл бұрын

Hi , the pc board I purchased this morning does not go into programming mode when I put the jumper on the prog j pins?

@nicksandtrickssa Жыл бұрын

Hi Vasilios, please make sure the door release is plugged in and the door is closed, this will turn the card on

@vasilioskelaris89 Жыл бұрын

@Nicks and Tricks hey its me ! I bought it from you this morning. I followed everything you explained and still nothing. My old card goes into programming mode but still doesn't work on ac . New card doesn't go into programming mode

@nicksandtrickssa Жыл бұрын

@@vasilioskelaris89 did u make sure the green cable is in the new card and the manual release was closed, the card will beep when u open and close the door

@vasilioskelaris89 Жыл бұрын

@@nicksandtrickssa my old board did not have a green wire connection like the 2 pins on the new board as per your video?

@rsaboertjie2109 2 күн бұрын

Hi great video however I'm struggling with my gate motor, it all of a sudden stopped working and would close but only open half way, tried to reset the limits but it closes and starts beeping 20 times what does that mean? No light are flashing and when i open it the LO light is on but when i close there is no light

@nicksandtrickssa 2 күн бұрын

@@rsaboertjie2109 thank you for the comment, it's seeing a collision midway, if the load pod is turned all the way clockwise then focus on the gate itself

@Novanod 8 ай бұрын

Nice video. Quick question. When setting the crawl setting must the gate be locked in the middle or in closed/open position? After, what I think, setting the limits. I tried setting the crawl, middle open and fully closed, it goes back and forth then it just long beeps and I turned no. 4 off and took the jumper off. My gate still doesn't slow down before fully opening and closing :(

@nicksandtrickssa 8 ай бұрын

Thank you for the comment, without trying the crawl, if it goes straight for the end-stop, there is a FET behind the motor fuse that could be blown, PCB will need repair

@Novanod 8 ай бұрын

My 25A fuse did blow, I changed it with a 20A (only one I could get at the time) since then it's not being able to crawl, just fast stop.

@nicksandtrickssa 8 ай бұрын

@@Novanod the FET is the first thing to go when the gate has a "collision", which blows the motor fuse

@Davitol0c0 Жыл бұрын

Hey brother thanks for the informative guides. My gate motor beeps 3 times consistently but the beep comes from the sensor against the wall. The AC light and RX light stays on. Can you advise me what the consistent 3 beeping problem could be?

@nicksandtrickssa Жыл бұрын

Thank you for the comment David, are we talking about the safety beam making the noise? Which sensor is it?

@Davitol0c0 Жыл бұрын

@nicksandtricks1849 yes there's 3 consistent beeps coming from the beam. I used a fresh battery but the beeping doesn't stop. The gate opens and closes fine. Thought it could be holiday locked with those 3 beeps..

@nicksandtrickssa Жыл бұрын

@@Davitol0c0 what is the beam name, do you know

@Davitol0c0 Жыл бұрын

@@nicksandtrickssa Its a centurion beam. Thanks for your help thus far, by the way. I guess I might have to reset the gate motor and hope the beep goes away..

@nicksandtrickssa Жыл бұрын

The only thing I can think of is if you have semi wireless beams (photon beam). That beam will beep when the batteries are low

@tlalemasiu1147 Жыл бұрын

Good day, thanks for the great video, I’ve recently re placed my battery, but now my gate can just close via the remote but won’t open, I have to manually open it, can you advice on the issue😅

@nicksandtrickssa Жыл бұрын

Thank you for the comment Tlale, is the gate heavy in 1 direction over the other? If so, on the pcb is a pod, next to the 3learning pins, turn it clockwise all the way

@tlalemasiu1147 Жыл бұрын

@@nicksandtrickssa thanks for the quick reply, i did that, I tried setting the limit as you indicated but the gate gets stuck at closed position and and gives double beeps

@nicksandtrickssa Жыл бұрын

Apologies for late response, can you put the gate in manual release and open it, check on the board where the White and Brown 2wire connectors is, is the led that says LO on, then close the gate and check if the led that says LC is on, if one of them is not on then please check the magnets, if they come on, try and run the limits with a fresh battery

@tlalemasiu1147 Жыл бұрын

Thanks it's all sorted

@ntuthuzelopakade2583 Жыл бұрын

Great video. Can you assist with the condominium mode?

@nicksandtrickssa Жыл бұрын

Thank you for the comment, what would you like to know about the condominium mode?

@ntuthuzelopakade2583 Жыл бұрын

@@nicksandtrickssa Thanks I would like to know how do you put this type of board on that state. I might have missed something on this video after trying it.

@nicksandtrickssa Жыл бұрын

Hi, I did not go through it in the video, dipswitch 2 on, puts the card in condominium/free exit mode. The motor will open all the way without stop and autoclose after beam interuption

@ntuthuzelopakade2583 Жыл бұрын

@@nicksandtrickssa Thank you so much I will try it out.

@doochies 2 ай бұрын

Hi Nick ,while setting the gate limits as per your video after putting the jumper, prog j ,pressing and releasing the button ,the gate closes then stops and starts beeping then stops but does not open, bear in mind its an old controller pcb

@nicksandtrickssa 2 ай бұрын

Thank you for the comment, does the closed limit light turn on when reaching the end, normally it does that beeping when it cannot find the magnet at the end of a run... Turn the motor to manual, then close all the way... Look for the brown and white wires and see if the LC led is lit, then open all the way and check for the LO led

@roelofvanbreda9864 11 ай бұрын

Hi... Any video on how to remove a remote from the ET500 gate motor?

@nicksandtrickssa 11 ай бұрын

Thank you for the comment, on the old ET500 you have to reset the receiver

@tejasgihwala1313 7 ай бұрын

Hi, awesome video. I have the green ET motor and it randomly doesn't open and then randomly it will be fine again. Do you have any ideas what i can try please? There are no beeping sounds it just doesnt respond when trying to open Battery was replaced within the last few months.

@nicksandtrickssa 7 ай бұрын

Thank you for the comment, if it does this after not being used it can only be dry joints on the pc board, it will work fine after about 5 minutes, if you have a third party receiver tho it can be the receiver as well, see what happens when you open and close the gate 4-5 times in a row... This is when pc board gets hot, then if you leave it for 5 minutes it will work again

@tejasgihwala1313 7 ай бұрын

@@nicksandtrickssa thank you for the advice. What's interesting is it did it tonight after one open and close if that makes sense. Then it wouldn't open again within a few mins. I tried with my wife's remote and also nothing. I'll give it a try in the morning as you've suggested. Out of interest if it's dry joints as you pointed out, what is the fix for that?

@nicksandtrickssa 7 ай бұрын

@@tejasgihwala1313 dry joints is where the solder gets hot and the gap between solder and the pin is too great for the signal to pass, or a crack on the solder joint that get exaggerated when the board heats up. so you can resolder the tracks which connects to the relays or it could be a bad or faulty relay as well, sending the board in for repair, if no insect damage is visible, can sort out the issue also.

@tejasgihwala1313 7 ай бұрын

Thanks a lot for all the advice. I opened and closed the gate 6 times and it seems fine now lol. Happens randomly which is strange. Struggling to reproduce the fault

@nicksandtrickssa 7 ай бұрын

Okay, thank you for the feedback

@junaidshamsoodien4564 Жыл бұрын

Hi whats the 2nd pot for? I know the one is for load... Is the other 1 speed?

@nicksandtrickssa Жыл бұрын

Thank you for your comment Junaid. Put the Progj jumper on while gate in closed position, turn dip switch 4 to the on position, press the set button. The gate will pause and then start opening, then it will close and beep, remove Progj and turn dip switch 4 to the off position. It does not make the gate faster but it will make the ramp down distance shorter.

@junaidshamsoodien4564 Жыл бұрын

@@nicksandtrickssa thank you for the reply and vid, much appreciated. Any idea what the 2nd pot is for?

@nicksandtrickssa Жыл бұрын

The pod by the AC circuit is to adjust the DC charge voltage to the battery, not to be adjusted.

@junaidshamsoodien4564 Жыл бұрын

@@nicksandtrickssa thank you, that clears that question 🙂what should the voltage be set at?

@junaidshamsoodien4564 Жыл бұрын

@@nicksandtrickssa thank you, sorted and programmed the shorter ramp down

@grantross1522 10 ай бұрын

Hi Nick great video, Please advise. My gate opens and will not close sporatically. It beeps but remains open. When I wait a few minutes it closes after pressing the remote.

@nicksandtrickssa 10 ай бұрын

thank you for the comment grant, does it always do it? It could be dry joints on the pcb

@grantross1522 10 ай бұрын

It's only been doing this recently

@nicksandtrickssa 10 ай бұрын

@@grantross1522 it could be dry joints on PCB, unless you have a meroon cover and it only does it during loadshedding

@grantross1522 10 ай бұрын

@@nicksandtrickssa Thank you, It's a blue cover. What should I do if it's dry joints?

@nicksandtrickssa 10 ай бұрын

@@grantross1522 but I blue cover is not a et 500, apologies. Do you know which motor you have

@angeliquepetersen792 Жыл бұрын

Hi.I bought a new pc board and now tryingvto set the limits of the gate,can't seem to get the limits sets.The gate closes and opens,then beeps multiple times.Can you please help?

@nicksandtrickssa Жыл бұрын

Good day Angelique, it sounds as if the gearbox is the issue, ehat was the reason for replacing the PCB? If you see oil anywhere, you should have the Base looked at.

@angeliquepetersen792 Жыл бұрын

@@nicksandtrickssa Thanks for the reply. The gate just wouldn't open properly anymore.Initiallybwe thought it was due to loadshedding.Replaced the battery.when this didn't work we had the pcb looked at.It was advised that replacement of the board is needed and thats what we did,but we can't get limits set.

@nicksandtrickssa Жыл бұрын

It would appear to be either the inner motor or gearbox if the battery and pcb did not fix the problem

@angeliquepetersen792 Жыл бұрын

@@nicksandtrickssa Thanx man.Will have to check it out then.

@nicksandtrickssa Жыл бұрын

If you are in the Cape Town area, feel free to take it to Rsec Security Equipment Center, Bergvliet

@kyledamon1806 Жыл бұрын

Hi thanks for the helpful videos.. I've tried setting my motor after watching this video..but it only moves about half a metre then beeps 20 times exact..I've changed the battery and limit senses but still can't the motor function..can you please assist me

@nicksandtrickssa Жыл бұрын

Thank you for your comment Kyle, the 20 beeps is the hall effect sensor not being seen by the rev counter... The magnet on the inner motor does not see the little nob on the board next to it. If you turn the magnet, on the board there is a led called enc, the light should go on and off when u turn it. If not let me know.

@kyledamon1806 Жыл бұрын

@@nicksandtrickssa thanks for your reply..I'm at the motor now but I can't find the magnet you referring to

@nicksandtrickssa Жыл бұрын

@@kyledamon1806 to the left of the card is the inner motor. On top of it is a wheel, that is the magnet

@KingSeptember 9 ай бұрын

@@nicksandtrickssahi nick my gate motor dc 500 it's stuck on closing its doesn't open and the green light on board it's flashing... Please help I don't know what to do now

@nicksandtrickssa 9 ай бұрын

Thank you for the comment Kyle, the motor works on beep codes, is there any beeps or does it beep for as long as you hold the remote?

@RooshevNaidoo Жыл бұрын

Is there a way to deactivate the crawl function?

@nicksandtrickssa Жыл бұрын

Good day Rooshev, thank you for the comment. You can only make it shorter.while the gate is in the closed position, take the cover off and put the Progj jumper on. Turn on dip switch 4. Press the set button. The gate will pause and then open and close, and beep. Remove Progj jumper and turn dip switch 4 to the off position. The crawl distance will now be shorter and the gate should operate faster. Please like share and subscribe

@RooshevNaidoo Жыл бұрын

@@nicksandtrickssa Great man, thanks.

@shaunphilander9844 9 ай бұрын

Hi. My E.T motor randomly opens my gate without pressing the remote. Ive added a new battery but it still does the same. Could it be the motherboard? Its the same as the one in the video. E.t 500

@nicksandtrickssa 9 ай бұрын

Thank you for the comment Shaun, if you have a standalone receiver, then it could be at fault, if you tried adding a remote lately, it could be a neighbours remote opening your gate

@KingSeptember 9 ай бұрын

@@nicksandtrickssahi nick please help my gate stuck on close does open or respond to remote

@nicksandtrickssa 9 ай бұрын

Can you press the set button on the board and let me know what it does plz

@shaunphilander9844 9 ай бұрын

@nicksandtricks1849 thanks. I did add an extra remote

@nicksandtrickssa 9 ай бұрын

You will have to reset the receiver and program your remotes over

@craigcarelse5485 3 ай бұрын

Hi Nick I have an ET 500 motor. When opening, it works perfectly but at times when I press the remote to close, it just beeps once but doesn't do anything. Sometimes it doesn't even beep at all and nothing happens when I try to close it. After about 10 minutes it will close perfectly again. PLEASE HELP 😭

@nicksandtrickssa 3 ай бұрын

Thank you for the comment Craig, does it happen when it's hot outside or just randomly? If it only occur when it's hot or when the motor has been opened a few times it can be dry joints on the control card

@elidnazmom Жыл бұрын

Hi need your assistance. The battery was changed but the gate still won't work. It beeps 2 times then 5 times. What could be the problem 😊

@nicksandtrickssa Жыл бұрын

Good day Zandile, thank you for the comment, after it does the long beeps, then the 5 beeps, did you try opening it again? Normally after a full restart the board can sometimes do that and the work correct after the 5 beeps

@elidnazmom Жыл бұрын

@@nicksandtrickssa thank you so much for your response. So it beeps the two times and then immediately 5 times and I tried again opening it but just the beeps keep repeating . And this is immediately after the battery change. It's been off for about 4 days now till I got the battery. Does the battery maybe need to charge first?. 🤔 . I'm so confused. I thought the battery change would help. Really appreciate your help

@nicksandtrickssa Жыл бұрын

@@elidnazmom can you check if the AC light is on, also there is a dial next to the white and brown cables, turn it to the right hand side half turn

@elidnazmom Жыл бұрын

Im going to open the box again and try to find a light. But the gate now is only beeping once but still won't open.

@nicksandtrickssa Жыл бұрын

@@elidnazmom did u turn the dial? Does it beep for as long as you hold the button as well?

@capeofstormz5974 10 ай бұрын

Yoh,that background music, man.

@nicksandtrickssa 10 ай бұрын

Apologies, I'll be remaking some of the older clips, what did you need help with?

@nicksandtrickssa 6 ай бұрын

Good day, please check the update on the video, a bit late but please have a look kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@vixifojeremia1179 Жыл бұрын

My gate always open first. I don't know where to press anymore

@nicksandtrickssa Жыл бұрын

Thank you for the comment, if you give me more info I can attempt to assist.

@user-sb6cb1ec1j 4 ай бұрын

I program my motor but my gate don't close

@nicksandtrickssa 4 ай бұрын

Thank you for the comment, does it not close during the setup or after?

@tianvanwyk9678 Жыл бұрын

Hi Nick, my gate does not run the full setup cycle. It closes, opens and then stay open and beep. Please help😢

@nicksandtrickssa Жыл бұрын

Thank you for your comment Tian, please check if both the LC and LO lights turn on, your opening magnet or switch could be faculty. The brown and white wires, has markings and a led, please check that

@tianvanwyk9678 Жыл бұрын

@nicksandtricks1849 Thank you Nick, I've taken out the LO and LC magnets and gave them a good clean. Both are working and when pressing the red button on the card it beeps two times and then closes, same to open. Will run the setup now to see if all is in working order. Will let you know.

@tianvanwyk9678 Жыл бұрын

@nicksandtrickssa Жыл бұрын

@@tianvanwyk9678 when the card does the beeps it means there is a AC power issue, check if the AC led bottom left behind the heatsink is always on, if not, check the AC transformer

@tianvanwyk9678 Жыл бұрын

@nicksandtricks1849 LOADSHEDDING. Did the setup and all 👍. Will I be able to program any gate remote to the card? I've got a 4 button EXO which I'm using with my one gate. Will I be able to program one button for the DT500?

@johanroos3993 9 ай бұрын

Background Music to loud

@nicksandtrickssa 9 ай бұрын

Thank you for the comment Johan, anything u missed or need to know, that I can help you to with?

@nicksandtrickssa 6 ай бұрын

Hi Johan please have a look at the updated video, I know it way too late but if you could let me know if it's better now? kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@dromaromar8827 7 ай бұрын

Please get rid of the background music, makes it hard to hear what you are saying

@nicksandtrickssa 7 ай бұрын

Thank you for the comment, what part did u need help with?

@dromaromar8827 7 ай бұрын

@@nicksandtrickssa . All good , figured it out eventually

@nicksandtrickssa 6 ай бұрын

Good day, a bit late but here is an update of the video kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@user-fx8nn6lb8h 6 ай бұрын

Your music is too loud. I cant hear your voice clearly.....

@nicksandtrickssa 6 ай бұрын

Thank you for the comment, please see kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@Luxie296 5 ай бұрын

Couldn't hear a thing you were saying. The music drowned out your voice 😢

@nicksandtrickssa 5 ай бұрын

The you for the comment, please see the new video kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@MalcolmJRussell 4 ай бұрын

Canot see the point of adding music to an instructional vidoe - its a distraction

@nicksandtrickssa 4 ай бұрын

Thank you for the comment Malcolm, I dnt see the point of not cover over the noise of a busy cape town main road with shouting in the back ground also, I thought I'd atleast make it a little more bearable with music. Apologies. Please see kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html Update video

@jeremyrose1518 Жыл бұрын

Why does there have to be music on every video..... Just lamit and give the info

@nicksandtrickssa Жыл бұрын

Thank you for your comment Jeremy, Unfortunately i record in a empty shop on a Cape Town Main Road, and i have to mask the noise during recording.

@tianvanwyk9678 Жыл бұрын

You are very rude. Nick are doing these videos to help us and not that he needs to. Go to a shop and sort out your problems yourself if the music is bothering you.

@nicksandtrickssa 6 ай бұрын

Hey Jeremy, apologies for the very very late update but here is an updated video of your interested kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html

@nicksandtrickssa 6 ай бұрын

@@tianvanwyk9678thanks for your comment, please have a look at the updated vid kzfaq.info/get/bejne/Zq97aqZ83KyzmaM.html