How to Program Your Rhino ESC

Рет қаралды 8,758

Жыл бұрын

www.negativegrc.com
/ negativegrc
/ negativegrc
/ negativegrc
#negativegrc #lcgcrawler #trx4sport #holmeshobbies #crawlmastermini #defygravity #bellydragger #dontletgravitywin

Пікірлер: 69

@TheOtherSock-728 Жыл бұрын

This Video was super helpful. The USB Cable advice was spot on for my problem!

@peanutbutter8713 Жыл бұрын

Thank you Jess! All I need now is the esc when it becomes in stock again

@skinner1987 5 ай бұрын

Awesome material, mate!

@jimlayhey1965 Жыл бұрын

thanks jes for all the help best customer service i gave ever seen

@jazzwrights Жыл бұрын

Your on top of the game with customer services #DEFYGRAVITY

@Furadi Жыл бұрын

Woohoo good walkthrough!

@miniboom007 Жыл бұрын

Thanks for the video.

@richardparkiii8355 10 ай бұрын

So, It shows connected, but when I click the M1 is says didn't connect. I tried 2 different cables. Any suggestions?

@dslfrk59 Жыл бұрын

I must be doing something wrong. I installed it and opened the configuration tool but when I try to connect it says m1 did not connect

@anthonyescobedo2142 Ай бұрын

I'm striking out all around here! My green light lights up, but the tablet doesn't load the driver. I'm running windows 11. I'll try it with my laptop and see what happens later.

@TheHammer Жыл бұрын

I'm having trouble getting my rhino esc to work on my new Sanwa M17. It worked great on my M12s no problem. The only way I can get it to work on my M17 is change the Throttle type from f7:b3 to f5:b5. When I do that, it works, but very low power and it will not let me calibrate the throttle at all.

@NegativeGRC Жыл бұрын

I talked to Conrad and he said to try FH4 or up one slower from what you were on

@TheHammer Жыл бұрын

@@NegativeGRC 10-4. Thanks! I'll try that now

@TheHammer Жыл бұрын

@@NegativeGRC didn't work on three different type receivers

@NegativeGRC Жыл бұрын

@@TheHammer I'm sorry I'm not more help. I have never messed with the Sanwa stuff before.

@TheHammer Жыл бұрын

@NegativeGRC thanks for your help. Fwiw, I got it working for the most part. Finally discovered for whatever reason the epa was at 70% and 30%. Turned that up and it seems normal. However, it will not let me calibrate the throttle.

@billderas3420 7 ай бұрын

What about using a Windows 11 computer??? Cannot get mine to work.

@dubbleportion 4 ай бұрын

I here 1.99 software will help with heat how do you do that,??

@NegativeGRC 4 ай бұрын

Rick you would do all the steps in the video you just go to the other tabs at the top of the software and load the new firmware

@blakesanfilippo3591 Жыл бұрын

can this be done on the Chromebook or anything have to be a Windows computer

@NegativeGRC Жыл бұрын

The program runs on Windows only as far as I know.

@arkansasrcnewbie 29 күн бұрын

Is there an option for the built in BEC?

@NegativeGRC 29 күн бұрын

The BEC is adjusted with the DIP switches on the board. There's a diagram on the Negative G website

@arkansasrcnewbie 28 күн бұрын

@@NegativeGRC thank you 😊

@BK33REVIEWS Жыл бұрын

Would it be possible to mount a external fan to these escs

@NegativeGRC Жыл бұрын

I'm sure you could but it's not really necessary.

@jebrc 5 ай бұрын

mine gets super hot@@NegativeGRC

@andyp7109 7 ай бұрын

So is drake the drag brake? Everything else seems rather straight forward for programming

@NegativeGRC 7 ай бұрын

You should see a check box on the left for "Brake On Stop" and on the right side there is a slider for "Stopped Brake Level"

@Clodercs 8 ай бұрын

is there a way to adjust batt cutt-off voltage???

@NegativeGRC 8 ай бұрын

Yes. On the 3rd tab at the top labeled "Input" there are some voltage parameters

@Clodercs 8 ай бұрын

@@NegativeGRC thank you very helful video for a great esc motor combo.

@vinnyilaria2064 Жыл бұрын

How will this worked paired with a yellow jacket motor from 3 brothers rc

@NegativeGRC Жыл бұрын

Just fine 👍👍

@vinnyilaria2064 Жыл бұрын

@@NegativeGRC perfect thank you

@vinnyilaria2064 Жыл бұрын

Last question u forgot to ask I also have a castle bec I was gonna use how will that pair with this

@NegativeGRC Жыл бұрын

@@vinnyilaria2064 Castle BEC is not required if you only need 8.2v. This 80A Rhino has a built in 8.2v BEC.

@vinnyilaria2064 Жыл бұрын

@@NegativeGRC okay I wasn't sure I have dual 7.4 volt servos for my 4ws plus my reef's winch

@miniboom007 Жыл бұрын

I got win7. It won't work and haven't been able to calibrate it either. Dead underwater. Hopefully I can find some local that got it to work.

@NegativeGRC Жыл бұрын

The USB driver is included in the download. If you look in the folder CH341SER in your download the driver setup should be in there. There is an x86 and an x64 bit driver depending on what you are running.

@miniboom007 Жыл бұрын

@@NegativeGRC I tried on my wifes laptop which has Windows 10. And nothing. So checked the cable connections. I think I might have a bad USB cable. Do you know what kinda of USB cable it is?

@NegativeGRC Жыл бұрын

@@miniboom007 This Amazon Basics is the one I use in the video: www.amazon.com/dp/B01GGKYN0A?ref=ppx_yo2ov_dt_b_product_details&th=1

@miniboom007 Жыл бұрын

@@NegativeGRC thanks. Gonna walk over to bestbuy see if they have the cable. If not, will order it.

@miniboom007 Жыл бұрын

I got the C type cable from Bestbuy. I installed the x64bit driver since I am running Windows 8. Was able to program. But still unable to calibrate. Gonna try a different transmitter. Baby steps over here LOL. Thanks for advice.

@Charlieoil 7 ай бұрын

How to adjust the voltage to the servo???? I have a 40amp ESC.

@NegativeGRC 7 ай бұрын

You need to use a BEC or a direct power servo with the 40A

@Charlieoil 7 ай бұрын

Yes I found that out. I will end up with the 80amp. @@NegativeGRC

@Charlieoil 7 ай бұрын

Can you adjust the voltage to the servo with the 80AMP??? Great video by the way.

@NegativeGRC 7 ай бұрын

@@Charlieoil yes the internal BEC on the 80A is adjustable up to 8+ volts

@4birdaerial 6 ай бұрын

Does this work with Mac ?

@jesscneal 6 ай бұрын

Windows only sorry

@user-xc1ek3gv4f Жыл бұрын

안녕하세요 같은 모터변속기구매해서장착준비중입니다 그런데 모터쪽 발열이 많이생기더라구요 혹시 지금쓰고계신 모터나변속기 발열이없는지 궁금합니다

@NegativeGRC Жыл бұрын

If you operate the ESC in sine mode continuously for long periods you will get some heat build up. Also you want to make sure you adjust the tune to your motor KV.

@user-xc1ek3gv4f Жыл бұрын

@@NegativeGRC 감사합니다~~

@nate4024 Жыл бұрын

How to change the bec voltage

@NegativeGRC Жыл бұрын

There are 2 dip switches on the board. Both should be ON for the highest voltage. I added an image to my site: negativegrc.com/product/rhino-am32-crawler-esc/

@Clodercs 8 ай бұрын

The link to upload the software does not work!

@NegativeGRC 8 ай бұрын

I just checked the link on my site. Seems to work for me: rhinoesc.com/download/

@Clodercs 8 ай бұрын

@@NegativeGRC thank you i will try that..also i have trouble with the esc cutting off on certain demand of power, it sometime shut off and dont turn on whatsoever i do!! The batt say around 32% left , a 3s!!

@ericsmith3317 Жыл бұрын

Dip switch settings , how do I get it on the highest voltage possible? (Yes y'all I know it's on the site.. but it'd be great if it was explained in video format)

@NegativeGRC Жыл бұрын

It's pretty simple. Both switches to the letter side (ON KE) is 8.2v. Page 3 here: rhinoesc.com/download/RHINO_ESC_Manual.pdf

@NegativeGRC 6 ай бұрын

@@KutterNixon You just push them with a small screwdriver to the position you want them. Those are called DIP switches. Both switches AWAY from the "1" and "2" will put you at 8.2v. There's an image here: negativegrc.com/product/rhino-am32-crawler-esc/

@KutterNixon 6 ай бұрын

thank you, ive never encountered dip switches before @@NegativeGRC

@jimlayhey1965 Жыл бұрын

just bought this off you the link below dosnt work

@NegativeGRC Жыл бұрын

Email me. Their site is down for some reason

@jimlayhey1965 Жыл бұрын

do you no how to do factor reset on software i updated firmware now motor wont turn