How to Properly Jack up a C5 or C6 Corvette (Several Methods)

No video

How to Properly Jack up a C5 or C6 Corvette (Several Methods)

Рет қаралды 99,798

Күн бұрын

WARNING: Please read the manuals for your tools, jacks, ramps, lifts and vehicles for *specific manufacturer approved techniques.* This video is for entertainment purposes only. In this video I will show you several methods I use to jack up a C5 or C6 Corvette. Methods shown include ramps for the front and back, jacking the front, jacking the back, putting the entire car on jack stands, jacking from the sides and using a quality Maxjax 2 post lift. Take a look!!
MaxJax 2 Post Lift Review: • Maxjax 5 Year Long Ter...
How to Build Wood C5 Car Ramps: • HOW TO BUILD WOOD CAR ...
*************************************************************************************************
Any purchase made by clicking one of the links below (even if you purchase a different product) helps support the channel - Thank You!.
As an Amazon Associate I earn commission from qualifying purchases.
🔥 C5 TUNE-UP PARTS & BELTS
* C5 Copper 20k Mile Spark Plugs: amzn.to/3VIM4xK
** C5 Iridium 80k Mile Spark Plugs: amzn.to/3TKuNlj
*** GM Spark Plug Wires: amzn.to/3U1LABC
**** MSD Spark Plug Wires: amzn.to/3PPQM9s
***** Main Serpentine Belt (Alt & Pwr. Steering): amzn.to/3JoebeB
****** Shorter AC Compressor Belt: amzn.to/3PRCQvt
🔥🔥 HARMONIC BALANCER/DAMPNER JOB - Parts & Necessary Tools**
1. Harmonic Balancer that is on MY C5: amzn.to/38BxKAL
2. LS1 & LS6 Harmonic Balancer Puller: amzn.to/3l9IYjp
3. LS1 & LS6 Harmonic Balancer Installer: amzn.to/3IIYewG
4. LS1 & LS6 Flywheel Holder for torqueing balancer bolt: amzn.to/3ToNr1q
5. LS1 & LS6 ARP Balancer Bolt: amzn.to/42QPgcj
6. LS1 & LS6 GM Crank Bolt: amzn.to/3lbrJy5
7. Timing Cover Seal (GM 296-02): amzn.to/49huqW4
8. Seal Puller (Crank seal in timing cover): amzn.to/4cB7KSJ
9. Seal Installer (Good to have, but not 100% required): amzn.to/3TL3c3h
🔥🔥🔥 Exterior Products on My C5 Corvette:
*Stainless 3.5" Exhaust Tips: amzn.to/3npnItN
**AmeriLite Front C5 Turn Signals: amzn.to/40jU73p
***Spoiler King Low Rise C5 Spoiler: amzn.to/3Gb3x9F
⭐C5 & C6 Shock Upgrade! - (Uses C6 Z06 Shocks!)
* Front: amzn.to/3Hs2Ol8
** Rear: amzn.to/3NoSyOc
*** How to install C6 Z06 Shock Video: • C5 Corvette Shock Upgr...
⭐⭐ Essential TOOLS for your Garage!
1. Motive Power Brake Bleeder - C5 & C6: amzn.to/48r7xOy
2. Floor Jack : amzn.to/49DHQeD
2. Jack Stands 16-3/4" Tall (Decent): amzn.to/3x60hqk
3. Jack Stands 23-13/16" Tall (Great): amzn.to/3x7Kqrf
4. OTC Fuel Pressure Tester: amzn.to/3T1lhv0
5. C5 (all) & C6 base models only - Aluminum Lifting/Jacking Pucks: amzn.to/3qVyxn6
6. C5 (all) & C6 base models only - Rubber Lifting/Jacking Pucks: amzn.to/3nzDGiC
7. Stant Cooling System Pressure Tester: amzn.to/3A28XjP
8. Adapter - Expansion Tank to Stant Pressure Tester: amzn.to/41ORCXF
9. Battery Tender Junior: amzn.to/3ig4Gk1
10. Jumper Cables: amzn.to/3OMSUMZ
11. Good Multimeter: amzn.to/377apXq
12. Great Multimeter: amzn.to/3F0fLju
13. Injector (Noid Light) Test Kit: amzn.to/3xoVl3T
14. Floor Jack Crossbeam : amzn.to/3T1TXg1
⭐⭐⭐ Scan & Tuning Related
* EXCELLENT TUNING BOOK - Engine Management/Advanced Tuning: amzn.to/39PkCZw
** Entry Level Scan Tool: amzn.to/4cB7Ae9
*** Mid-Range DIY Scan Tool: amzn.to/43HPP8C
****Best DIY Scan Tool -OTOFIX D1 Lite Advanced. Bi-directional: amzn.to/3T3ATOs
⭐⭐⭐⭐ C5 & C6 Full Synthetic Oil and Oil Filters!
* Mobil 1 5W-30 Synthetic Oil: amzn.to/3LZGAsW
* Castrol Edge 5W-30 Synthetic Oil: amzn.to/46LBZT9
* Fram Ultra Synthetic Filter: amzn.to/48SPMsL
* WIX Oil Filter: amzn.to/3wlW5Xn
🏁 Apparel / Garage Banner:
*Sweet C5 Corvette T-shirt: amzn.to/3iF1M8A
**Missing 10 MM Socket T-shirt: amzn.to/3IN3em1
***C5 Corvette Garage BANNER: amzn.to/3qeC3Le
****C6 Corvette Garage Banner: amzn.to/3NSXXwO
💺 Amazon C5 Seats: amzn.to/3nYciKA
*Sunshade - Save you interior!: amzn.to/43s1vv8
** Front Air Dam Kit (3 Piece for C5 Corvette): amzn.to/3EEhATh
*** Lloyd Mats for C5: amzn.to/3tIIgOY
🏛️ C5 and C6 Corvette Storage/Winter Covers**
* C5/C6 Batman Cover - Indoor storage: amzn.to/3QztdSM
** C5 Higher Quality Cover: amzn.to/3S92rCa
*** C6 Higher Quality Cover: amzn.to/3QkSwXM

Пікірлер: 114

@ulyssesgonzalez5655 3 жыл бұрын

Best raising a corvette video on KZfaq...

@Toys4Life 3 жыл бұрын

Appreciate that sir!

@wrthrash Жыл бұрын

No one asked me, but I use 2 big 3 ton jacks from both sides, jack up 20" on front pucks, add 6 ton stands, then jack up the back pucks and add stands. So crazy as it looks like it's levitating, and it's quick and easy!

@ralphconradt1434 Ай бұрын

how about making a brief video. Thanks

@ar_min_m 3 жыл бұрын

I like the OCD mindset you have. I appreciate that kind of precision of imagining the amount of force loaded on each part of the undercarriage

@feardc2050 6 ай бұрын

OCD= obsessive corvette disorder

@WakelessXistance 5 ай бұрын

Soooo glad I watched this first! I was gifted my father-in-law’s Lingenfelter C5 a few months ago, and after taking it out of the garage for a Sunday drive, the right front blinker went out. I thought about just putting a puck in and jacking up the corner, but I heard horror stories about people jacking up a corner to replace a flat tire or something, only to have a catastrophic failure of sorts with expensive and severe body damage. That being said, I think I’ll jack it up under the front cradle and use my stands. Thanks for the video!

@Toys4Life 3 ай бұрын

Be sure to refer to your owner's manual for the proper locations if you're unsure.

@user-mm4je1sb9b 2 жыл бұрын

I'm 55 years young this past month and wouldn't consider owning this vehicle without the 2-post 10K lift bolted to the floor in my shop. 🤩🤩 Sucks to get young!

@Toys4Life 2 жыл бұрын

Would a Mustang be any different for you - or also require a 10klb lift? Getting older beats the alternative of pushing up dandelions....😬

@daryltaylor659 3 жыл бұрын

Just bought my first Vette, thanks a ton for this video, helped alot

@shawnjackson5623 Жыл бұрын

The best video on how to correctly jack up your Vette. You even covered the side puck method and why it’s not the greatest way to jack your car up. Subscribed 🍻

@Toys4Life Жыл бұрын

Appreciate that sir!

@raymondshartrand2417 8 ай бұрын

I just built the wooden ramps a couple of weeks ago. They are awesome. I have used them twice in the last two weeks.

@williamgreen5371 3 жыл бұрын

Perfect - exactly what I was looking for!

@dylanlandaker8186 2 ай бұрын

Thank you for showing where to put the jack stands

@bidensucks2066 2 жыл бұрын

For my c6 corvette I bought two light weight red low profile 2 ton 4 pump jacks from harbor freight, cost 110 ea. Plus the hockey pucks from Amazon ,14.99 set, took my used 20.00 rhino ramps I use for my truck and family car. Turned them side ways and sat the front tires in the ramp pockets. Thus no need for jack stands and was safe. This was easy , everything was light weight, and worked efficiently and perfectly with no problems. All for far less than race ramps and no having to mess with wood . Note after the front end was up the was enough room in the back at the jack point to get a regular jack in,( with hockey pucks) and raise the rear up to set the rear tires in my old used metal ramp pockets. This was far easier than anything I've seen on here,.....except the thousand dollar ramps . And I ain't paying that. My method was was cost effective and easy! Let's go Brandon!

@Toys4Life 2 жыл бұрын

Wow.

@tahoejohnny3991 Жыл бұрын

Dragging politics into cars. Double wow. 😔

@TJsVette 2 жыл бұрын

Got my mini ramps done tonight, I built what I call Wheel Cribs to go under the wheels to hold them tight while I do my oil change tomorrow.

@Toys4Life 2 жыл бұрын

Nice

@user-nt7dq7mz7y Жыл бұрын

Thank you for how to properly Jack up your C5 . I will be installing a Front Splitter with side skirts. 🇺🇸

@kpbhat2005 2 жыл бұрын

Amazing video. Very precise and nothing left for imagination.

@Toys4Life 2 жыл бұрын

Thank you sir!

@robbryant3125 Жыл бұрын

really helpful, great bit too on the twisting/torque effect of using the jack on the side lifting points. I just got a 2004 C5 and I love it but I've never had a car with such a low profile. This was super helpful, many thanks!

@Toys4Life Жыл бұрын

Glad it helped

@danlaur7973 6 ай бұрын

The problem with home made wood ramps is that part of the ramp is in your way as you crawl under the side of the car, Race Ramps makes a nice long low angle 2 piece ramp that detaches once the car is on the top of the ramp opening up the side of the car so you can crawl under it

@Toys4Life 6 ай бұрын

That's a Nice feature for sure if it works well.. That having been said, if you know you need to go pretty deep under the car, I usually just slide in with a creeper from the front.

@CooLMeTaL69 2 жыл бұрын

Very interesting to know about the flex of the chassis! That is good to know for sure. I might suggest checking the stability once raised a little with the hoist before going all the way up. Giver' a little shake...maybe you did that in the slight pause I saw? Either way it would be good to mention.

@Toys4Life 2 жыл бұрын

Great point!

@TheBayAreaArab Жыл бұрын

Awesome video, much needed

@Amarillobymorning777 2 жыл бұрын

Excellent video clip

@Toys4Life 2 жыл бұрын

Thank you very much!

@jsanfason Жыл бұрын

Very informative video! Nothing left out that I can see

@doncollins786 Жыл бұрын

You just answeredd my questions, thanks!

@randyteresi7284 5 ай бұрын

Great video!!! Thank you!! Your videos are always very informative.

@Eurolaflare 27 күн бұрын

I’m in luck I happen to have purchased race ramps 4 years ago so I’ll use them to get the floor jack in place

@BenFreedmanRacing 3 жыл бұрын

This was super helpful

@Toys4Life 3 жыл бұрын

Glad it was helpful!

@LHG86 4 жыл бұрын

Thank you. Great video.

@Toys4Life 4 жыл бұрын

Thanks!!

@nashrambler5246 Жыл бұрын

You INSPIRED me to build a set of duplicate ramps. Watched those videos too. Thank you!!! I noticed your car was pretty dirty in this video. How did you clean it up so well when I see your newer videos? I am six glasses in to Jack Daniels so maybe I missed a video. LOL!!! 😂 Keep up the great content man. 😎

@Toys4Life Жыл бұрын

Nah, just a good wash and maybe a little wax. Nothing special, yet!!

@papagigo1 2 жыл бұрын

Great video , thanks for posting !

@Toys4Life 2 жыл бұрын

Glad you enjoyed it!

@lionelborges8094 2 жыл бұрын

Lionel here in central California. Nice video. Here's some food for thought. According to the factory the 2 spots where you put the tape ate the recommended lifting points. Plus they make, as you called them, hockey pucks, for lifting the car. But I get your point. Just saying...

@Toys4Life 2 жыл бұрын

Thank you sir!

@jimgraham1404 25 күн бұрын

Thank you sir

@Toys4Life 25 күн бұрын

Thank you!!! Much appreciated!

@clamc2012 4 ай бұрын

Very nice. Thanks.

@rcghalohell 2 жыл бұрын

similar to my 370z. shouldnt really flex too bad from that other way if the wheel doesnt leave the ground, then again, im not sure of the wheel travel limit... ive definitely broken that rule wayyyy too much lol

@Twobarpsi 3 жыл бұрын

Great video!!🏁🏁🏁

@petercarey6883 4 жыл бұрын

Excellent video. Just curious why you haven't installed jacking pucks in the frame of the Vette? Save the Wave.🙋🏼‍♂️

@Toys4Life 4 жыл бұрын

Extra weight - don't want them to slow me down... J.K. We are a hockey family so I have about 99 pucks. It makes me smile every time I look at a puck!

@rayguarrotxena4423 3 жыл бұрын

Good on ya mate,,,good stuff,,and very safe,,

@Toys4Life 3 жыл бұрын

Glad you enjoyed it

@ss-5553 4 ай бұрын

Good video thank's

@mr.winkie 3 жыл бұрын

@5:02 do you know if this method is high enough to upgrade/replace the OEM exhaust? Not the headers, just the mid-pipe and cat-back? Wondering if there's enough room to work with your arms in get things in and out. I'm looking at a bolt-on Corsa Xtreme kit. Thanks! Great vid!

@Toys4Life 3 жыл бұрын

I have removed mine a few times - but always on the lift so I don't know for sure. I would ask the question on Corvetteforum.com. I am sure a lot of people have tried and will know for sure.

@Oversight85 2 жыл бұрын

Would it also be okay to use two jacks on the front lifting points? So, one jack on each side and get a friend to help you lift them at the same time to avoid flex? Then my idea was the insert jack stands, and do the same thing on the rear jacking points.

@Toys4Life 2 жыл бұрын

That should work fine, just do synchronized jacking (:-)

@innovateandinvest 11 ай бұрын

Secret weapon 🔥🔥🤣🤣

@Airman.. 3 жыл бұрын

genius!!!

@Toys4Life 2 жыл бұрын

Glad you enjoyed it!

@nonya5475 3 жыл бұрын

Those tall wood ramps look dangerous. No way I would use them lol!

@Toys4Life 3 жыл бұрын

I respect your opinion. I think if you saw them in person though, you might have a different view. There plenty wide and plenty long and could support three times the weight of the C5 easily in my opinion.

@jessecampbell8007 Жыл бұрын

I’ve used them to lift a 9000lb ford F550

@MrWildfire4900 3 жыл бұрын

Curious, why do you jack with a piece of wood on the cradle? Why not just place the jack directly on the cradle?

@Toys4Life 3 жыл бұрын

I like to spread it out a little bit because aluminum can be brittle if you just catch the wrong edge. The wood deforms just enough to greatly reduce any potential issues in my opinion.

@markthompson5934 Жыл бұрын

Whats the measurements on your wood ramps i see 5 levels?

@Toys4Life Жыл бұрын

Towards the end there is a part with a tape measure lined up next to the ramp for reference. kzfaq.info/get/bejne/b6efnN1m187VdWQ.html

@gdog5841 Жыл бұрын

Your vids are awesome. Can you share any source/research that confirms it is alright to jack the front of the car from the CENTER of the crossmember? It is of course aluminum and does not seem sturdy enough to support the full weight of the engine off the ground. Thx.

@Toys4Life Жыл бұрын

I appreciate the kind words. The only documented authority that is going to stick their neck out telling you where to jacket is GM. It's in the owner's manual and I think I included a screenshot.

@chrisjay8718 8 ай бұрын

Thanks for the video....my 97 ""CHRISTINE"" &.I THANK YOU

@Toys4Life 8 ай бұрын

Welcome!

@aaronrunalls375 Жыл бұрын

First great vid... but i have to ask ...its says AND C6... are they very identical, so no C6 in video? Thanks

@stellijer 7 ай бұрын

I just got a used MaxJax. I will be putting it in the garage soon. How about jacking up a C3 (I have a 74)? How similar?

@Toys4Life 6 ай бұрын

I'm not sure, before you put it in think about the cars you're going to lift the most and make sure your spacing will accommodate your favorite cars!

@stellijer 6 ай бұрын

@@Toys4Life Absolutely! I'll primarily want to lift the c3 (74) for work, but I also have a 2007 Impala SS for bumming around in, which I'll want to do work on. Maybe I'll get a c7 in the future... but that day hasn't happened yet. LOL

@Toys4Life 6 ай бұрын

If you have a large variety of vehicles, you can drill two sets of holes for one of the columns as well, something to keep in the back of your mind.

@stellijer 6 ай бұрын

@Toys4Life True. But I don't have a large variety at the time. The impala isn't that much wider and if I got anything too much bigger it probably couldn't be lifted in my garage anyway. Well, maybe creeper height...

@blackstaticband 3 жыл бұрын

I dont think it's a good idea to support the aluminum cradle like that w/jackstands. Too much weight on the thin aluminum edge. Not to mention the fact the jackstand top shape doesnt really hold it well and easy to fall off or shift

@Toys4Life 3 жыл бұрын

I understand your concern. At the end of the day, only lift your car in a way that makes you comfortable - and after you've read the owner's manual.

@jamien9327 4 жыл бұрын

Good video!

@Toys4Life 4 жыл бұрын

Thanks for the visit

@gforcecache 4 жыл бұрын

Once the jack lifts one of the ends, is there a reason you are not placing jack stands with pucks under the side lifting points? I own jack stands that allow jacking pucks.

@Toys4Life 4 жыл бұрын

Not really, I just prefer having the jack stands under the cradles rather than under the frame rails.

@Toys4Life 4 жыл бұрын

But what you suggest should work as well.

@exoticspeedefy7916 8 ай бұрын

Is it ok to leave it up on the 2 post lift long term? I have mine up there, it didn't quite line up with the jacking points, but was close, and on the chassis..

@Toys4Life 8 ай бұрын

I would have to defer to the manufacturer for the correct answer all that sir 🙂

@russwilliamson329 Жыл бұрын

What is the inside distance between your MaxJax please.

@Toys4Life Жыл бұрын

I think I included the dimensions in this with the tape measure shown so you can see if that it is from the base plate, not the column. This is a common question and if I had to do it over again - I would mount them in the same spot.

@marks146 4 жыл бұрын

your links don't appear.

@Toys4Life 4 жыл бұрын

Thanks - I just added the Index in the description and the cards to build wood ramps and the Maxjax reveiw now. Thank you!

@d3et1roi3t 2 жыл бұрын

I do have a Giant Beer Belly.. Now what do i do? lol

@Toys4Life 2 жыл бұрын

Taller ramps and jack - and a few situps? Cheers!

@link9alink9a71 2 жыл бұрын

👌👍

@Toys4Life 2 жыл бұрын

Sweet!

@casey5018 3 жыл бұрын

you have to have the doors cracked open when lifting the car

@Toys4Life 3 жыл бұрын

What?

@casey5018 3 жыл бұрын

@@Toys4Life you have to crack the doors open on c3 c4 c5 c6 when lifting them...at least that's how we do at the dealership. Might be different using a lift

@Toys4Life 3 жыл бұрын

@@casey5018 The C3 & C4 flexxed a LOT so I believe that. C5 and C6 are rock solid so I think that simply a carry-over habit that is no longer necessary. Over the past 5 years I have opened my C5s doors while it is on the lift too many times to count and have never noticed any binding issues what so ever.