How To Quickly Anneal Wire & Metal Sheets

No video

How To Quickly Anneal Wire & Metal Sheets

Рет қаралды 63,980

Күн бұрын

Discover various quick and easy ways to anneal wire and metal sheets with the help of John Sartin. John demonstrates how to anneal various metals with and without flux, discusses what temperature indicators to watch out for, and explains the special quenching considerations for other metals such as Argentium® Silver, red gold alloys and white gold.
Shop some of the suggested products based on those seen in this video:
Vermiculite Soldering Block, 13" ow.ly/sfc650G8vy3
Copper 6" x 12" Sheet, Dead-Soft ow.ly/vDDT50G8vDq
Solderite™ Pads, Hard ow.ly/kIxf50G8vEf
Smith® Silver Smith™ Acetylene and Air Torch Kit with Tank ow.ly/8J4R50G8vFx
Handy Flux for Soldering and Annealing ow.ly/XOhi50G8vGI
Non-Contaminating Flux Brushes ow.ly/f1PO50G8vH5
Sterling Silver 3" x 3" Sheet, Dead-Soft, Brushed Finish ow.ly/cXCj50G8vIP
Cupronil Anti-Firescale Coating/Flux Combinations ow.ly/y53K50G8vKy
Copper Round Wire, 1/2-Hard ow.ly/pp5250G8vYP
Argentium® Silver Round Wire, Hard ow.ly/I6v650G8w1w
14/20 Rose Gold-Filled Round Wire, 1/2-Hard ow.ly/QiQQ50G8w20
Rio Grande stands for makers who create with their hands and their hearts and who are courageous enough to make jewelry their livelihood.
Connect with Rio Online:
Visit Rio's Website:
Subscribe to Our Channel: ow.ly/dAbu309U7eg
Find Rio on Facebook: ow.ly/DpRd309U63Z
Follow Rio on Twitter: ow.ly/wdtU309U6oF
Follow Rio on Instagram: ow.ly/eu5A309U6vM

Пікірлер: 43

@cmevans 2 жыл бұрын

"Heat to 'bright cherry red" says one 'expert' video; "heat to dull cherry red" says another; "heat until the Sharpie disappears" was what my first instructor said; "heat until the shine dulls" says my current instructor. Then I get to this video. THIS VIDEO MAKES SO MUCH SENSE! I knew I could count on Rio Grande! Thanks!

@RioGrande1944 2 жыл бұрын

We are glad you found this helpful. Thank you for watching!

@ActiveAtom 4 жыл бұрын

Nice lessons, we will give this a try here, thank you we learn here and we did that wire rolling up for annealing consistency was fantastic. Lance & Patrick.

@AlwaysMetaling 4 жыл бұрын

Great and very helpful video. I liked hearings about using flux as an indicator. Thanks so much. 👩🏼‍🎨🌵🔨

@milouschmidt 2 жыл бұрын

Brilliant, simple and clear, all a student needs to start :) thanks!

@RioGrande1944 2 жыл бұрын

You are welcome! Thank you for watching!

@zero_____given 4 жыл бұрын

They make temp stick's, and it will melt when it's at the right temp you just rub it on the metal your heating,I'm not trying to take away from the video and I apologize if I sound that way, I'm actually subcribe to this channel.

@crystalfabulous 4 жыл бұрын

Thank you so much excellent video

@redman8067 4 жыл бұрын

Awesome! Subscribed!!!

@ibmoondance23 3 жыл бұрын

Thank you!!!

@jillianmorkan3319 4 ай бұрын

Really good video- to the point and really well explained!

@RioGrande1944 Ай бұрын

Thank you. We are glad you found it helpful.

@eyedownload 3 жыл бұрын

Fantastic info! Thank you!

@RioGrande1944 3 жыл бұрын

eyedownloader thank you for watching we are glad you like it!

@AltheaMayberry Ай бұрын

I'm a complete novice bench jeweler. I am taking a diploma course through New York Institute of Art & Design by Penn Foster. I'm working on my project, making an ID bracelet. I am to shape the links for the bracelet myself. The wire I am to use is 14 gauge brass wire. This wire is very difficult to bend with my round nose pliers, and is even worse using my stepper pliers. Of course, the course has taught me about annealing, but I wasn't sure how to go about it. There are no videos in the course. This video is very helpful. Thank you for making it. However, I do have one question. Can a butane torch be used to do the annealing?

@lorimichels4515 Жыл бұрын

Hi, where did you get the metal stand to hold your torch handle? Thank you.

@klcwarchitect 2 жыл бұрын

If you have a large quantity of wire, can you put it in a kiln? If so, what temperatures would you need for silver and copper and for how long? I use 8 gauge wire (it comes in coils ) and torching it ends up with very inconsistent results. I have heard temps between 1100 and 1300 degrees F for 30 min. for silver and cannot find info for copper.

@onelove762 11 ай бұрын

After annealing the metal such as brass does it go back to being hard after folding it?

@kroscuro 3 жыл бұрын

Coiling works great for fine wire, but ... What about wire that's too thick to bend in a coil like 6 ga? Or square, half round, or some bezel wires that you don't want to get twisted up? Also, you didn't mention (or maybe I missed it) fine silver - same as sterling?

@pattyjones5131 Жыл бұрын

Would nickel silver be annealed the same as sterling silver?

@palumbodesigns 3 жыл бұрын

I use paste flux a lot too.

@desijewelr4663 Жыл бұрын

Where you located, I have some Bangles-Brass metal featuring with Cubic Zirconia and poor quality rosegold plated. So I want re plating all approximately 30 Bangles, I'm not sure how and how much Cost for that ?

@user-qo3il3fz9m 3 жыл бұрын

Can it be useful? I want to know how to weld carbide with styrene with flex. Can you help me?

@RioGrande1944 3 жыл бұрын

Hello محمد نبيل, in order to best answer your question we spoke with our Tech Team. They wanted to know if you could provide them with an example or a photo of the items that you wish to weld in order to better understand your question? We look forward to assisting you!

@brucefulton 4 жыл бұрын

Any tips about annealing gold-fill wire and sheet?

@grannygrumbles4119 4 жыл бұрын

I would also like to know this. Especially gold filled wire. I am always sad that I can't purchase 19ga rose gold filled wire and use a lot of it. I'd love to be able to have a few ounces at a time of 19ga rose gold filled dead soft wire.

@brody334 2 жыл бұрын

What about Anne sling platinum sheet? Do you quench or air cool?

@brody334 2 жыл бұрын

Annealing

@RioGrande1944 2 жыл бұрын

Hi, for annealing Platinum, the most accurate way is to use a kiln, heat to 1700°f and hold for 15 minutes at which time you can quench or air cool. For torch annealing heat the piece to a bright orange glow and hold for about 1 minute and then quench or air cool. The time will depend on thickness of material. One thing to note is that if you're picking up the extremely hot piece of metal with tongs there is a chance of cross-contamination, so air cooling may be safer. We hope this answers your question, but please let us know if you have any others.

@enolarama 3 жыл бұрын

What is this torch you're using? Is it sold by Rio Grande?

@RioGrande1944 3 жыл бұрын

Hi Tammy, John is using the Smith® Silver Smith™ Acetylene and Air Torch Kit, and you can find it at Rio Grande by clicking on this link, ow.ly/j1Rv50D6NiV

@casandradaly9698 2 жыл бұрын

I’m starting to work with 8-12 ga copper and brass wire at home for my jewelry and figured annealing would make the process a lot easier. Can I just use a regular torch for this instead of the one you’re using?

@RioGrande1944 2 жыл бұрын

Hello, we will go ahead and ask our Tech Team and get back to you with with their answer.

@casandradaly9698 2 жыл бұрын

@@RioGrande1944 thank you!

@RioGrande1944 2 жыл бұрын

@@casandradaly9698 Not a problem! Our Tech Team got back to us and they said that, yes, you can use a torch to anneal metal. You will need to have a good size tip like the #2 tip from the Acetylene Air Torch and flux on the metal.. Place a X with a sharpie. Once the sharpie disappears the metal is annealed. We hope this helps and let us know if you have any other questions!

@casandradaly9698 2 жыл бұрын

@@RioGrande1944 thank you for the tips! I’ll try it out next time

@casandradaly9698 2 жыл бұрын

@@RioGrande1944 Is there a way to restore the brass color after it’s been annealed?