Good job am shepherd tembo from zambia I repair gearboxes that's my professional now I need equipment to use in my workshop

Thank you so much Your video 📹 is the best of all on KZfaq. Nadir from Algeria.

I love mechanic diesel truck and caterpillars ❤️

Hello Alvin! I have a Petrbilt 387 and I am repairing my Eaton Fuller 13spd. Before starting the repair I watched a lot of your videos. You are a professional and I wanted to ask you what is the right thing to do. What parts do you use for repairs, original or auto market? If auto market, which ones can you recommend.

Great video but it would help a lot if you would have shown the spacer and shim to the camera as you are putting them in place

Excelente información ahora ya no tengo mi una duda eso quiere decir que si lo hice excelente mi trabajo muchas felicidades my friends

Again very impressive!! Great job.

top job very informative as you worked ,thanks a lot from australia

Keep up the good work buddy

Good rebuild I'll have to use u next time

Gusto en saludarte desde North Dakota solo que no me fijé de dónde sacaste referencia para tomar el tiempo de ambos piñones

can you show how to test the shifting mechanism (splitter and hi/low)?

👍 Meu Amigo Gostei do Vídeo Só que Nessa Correria Ninguém Entende Nada Ok

Thanks for the video

Great video

Ginalingan masyado haha magaling magaling👏👏👏

Thank you for your video

thank you for this video !! i have a problem with my transmission the shifting splitter cylinder is leaking oil ... is hard to replace the O rings and gaskets??? anything special that i need to know?

Another great video parekoy!

Muito bom. Tenho um cambio igual, e não está transferindo da caixa leve para caixa pesada. Alguma solução?

Here’s the link for part 1. Thank you all for watching 🙏🏼 kzfaq.info/get/bejne/ldeffNx91brZgqM.html

Hey my rear bearing cover gasket is leaking can i just pop it off and replace the gasket while the transmission is still on the truck? Any specific spec to torque the nuts after i install the gasket?

Good Job!! Nice.

Why do the gears need to be timed? Balance?

Rtlo 18913 behind strong cat popping and rolling back on hard pull in low side, does it In reverse als0. Power devider looks good. Problem in the rear box?

WHAT KIND OF ASSEMBLY LUBE ARE YOU USING? GOOD VIDEO

Gracias amigo siempre saludos desde North dakota

Kalupit mo pre makananu mu lang apangalikut den haha, Ingat pare God bless

❤❤❤❤❤❤ thanks

if you put an 18 speed shifter on the 13 can you split the lower? or a different animal?

Hi. My truck is a 10 speed manual (Eaton) the gears stock was on high range (I was told that this was a minor issue) But The mechanic told me it's a big damage, they need to rebuild it for $ 3500 without labor!!!. I agreed. Then I found out, that he replaced it with another one, that one doesn't have a cooler (my transmission had one) tell me please if what the mechanic did is right/okay?. Should I accept this transmission ( the new one without the cooler)? He's working on the truck now, haven't finished yet.. I still have time... should I accept what he did or not?? Please reply 🙏

👍👍👍

Where are you located? I’m interested in rebuilding my DT12 thank you

Nice job bro

❤

Just bought a truck with a converted 9-13 speed. When splitting from high to low in high range it always grinds. Downshifting is fine. For instances, if I’m in 5h and upshifting to 6l, I preselect and attempt a normal shift but have to feather the throttle a lot to get it into gear without grinding. In my experience this is t normal. Any ideas what the issue could be?

Amazing 👏👏👍👍

Do you have to time the front case to the rear?

HI their any way to remove tha output shaft shaft bearing , inner bearing because play in my output yoke thank you

What grease do you use?

Are the two tapered bearings that go on the counter shaft supposed to be tight mine has play and won't stay tight?

What’s that green paste ?

Show gostei 👌

What r u looking for when I mark the gears

No shims on the counter shafts?

What is your location?

Vc e demais 👏

Just wondering why are you wearing that face mask for? Are afraid to get covid from those gears?

Your in a room ALL BY YOURSELF. Wth? 🤷‍♂️🤷‍♂️ 😷😷😷👎👎👎 Dislike the propaganda.

Why are you not pre soaking the synchronizer material you know that when you start that up if it’s not resolved you can take the chance of tearing the material off the synchronizer supposed to pre soak them. 😢 Don’t mean to step on your No but if you research the manufacture suggestion depending on where you’re purchasing your synchronizer give me freeso synchronizers in transmission fluid that way the material is pre-sold prior to assembly and it’s still a good idea for a little bit overcast like you have been on her when you were somewhere because I don’t know you reinstall your transmission immediately or not because if you do not free to Lucy this is just like pre. Luby automatic transmissions yes even though you fill out the transmission fluid when you put it in here and you put all the Torque on the disk you will. Premature take the life out of the transmission same concept I’ve been rebuilding the transmission for 40 years I know what I’m talking about and I’m very good at it I wish I would’ve thought about making video shoot no I just took a picture

👍👍👍