How To Rebuild Backhoe Hydraulic Steering Cylinder - Ford New Holland 555E

How To Rebuild Backhoe Hydraulic Steering Cylinder - Ford New Holland 555E - 4WD

Рет қаралды 10,583

Күн бұрын

Backhoe is a 1998 Ford / New Holland 555E.
We saw a puddle under the machine and it ended up being the steering cylinder. It's not too bad of a rebuild but it is a double action cylinder which is different then a standard cylinder.
Edited by: Dylan
Timecodes
0:00 - Intro
0:26 - Locating the cylinder
0:42 - Cylinder removal procedure from repair manual
0:48 - Loosen cap bolts
0:57 - Remove left wheel
1:03 - Unseat cylinder cap
1:11 - Break ball joints free
1:32 - Remove tie rods
2:42 - Remove ball joint
2:50 - Remove hydraulic hoses
3:25 - Remove oil
3:39 - Remove cylinder
4:07 - Closeup of old seal
4:18 - Remove old seals
5:16 - Install new seals
7:50 - Remove cylinder seals
8:33 - Install new cylinder seals
8:33 - Install new cylinder seals
10:18 - Seal kit part #
10:22 - Remove old seals
11:07 - Install new seals
12:40 - Mark which side of the cylinder had the end cap
12:55 - Install end cap on cylinder
12:15 - Reinstall cylinder
14:16 - Reconnect hydraulic hoses
14:50 - Reinstall ball joints
15:08 - Remove right wheel
15:18 - Reinstall ball joints
16:08 - Test the cylinder
16:54 - Reinstall wheels
17:30 - Remove jack-stand and test
#Backhoe #Ford555 #StabilizerCylinder

Пікірлер: 9

@troypeterson5536 2 ай бұрын

Great , thorough instruction and cautions. Will be doing this on friday

@larryeddington9170 Жыл бұрын

Thanks I am now looking at the same procedure for my 655E your video helped immensely. Then gonna do the boom swing cylinders, not leaking yet but dust shields are gone.

@BrollBrothersProductions Жыл бұрын

We have a video on the swing cylinders too, eventually we need to do the boom cylinder too as it is weeping a bit.

@user-ci2hl8ib1o Жыл бұрын

thank you for sharing sir

@luigisartori9758 Жыл бұрын

Looking for a video on start to finish for this job on a 1972 Ford 4400

@amoniable 3 ай бұрын

I have the 675E and transmission stopped going into gear and now won't start, any ideas/suggestions?

@BrollBrothersProductions 3 ай бұрын

Luckily we haven’t had any tranny problems yet. When you say it won’t shift do you mean the gear selector or the power shuttle forward reverse? If it’s the switch on the steering column I would check the connections that’s a purely electric toggle switch.

@amoniable 3 ай бұрын

@@BrollBrothersProductions yeah it's on the steering column, seems to just not want to get out of neutral but if I'm honest I have no idea what I'm doing in general with it, my neighbor let me have the backhoe and I'm trying to figure it out as I go. I can "trick" it to get into forwards by up-shifting at the same time as putting it into forwards gear but no luck outside of that. The parking brake indicator light is also stuck on which I think might also be at fault of not letting it out of neutral

@BrollBrothersProductions 3 ай бұрын

@@amoniable the parking break is gone on mine lol. If you look up the manual you can get a wiring diagram, if I recall the forward reverse switch goes through the console and plugs into the transmission. If that plugs looks okay you might just need a new switch, not sure if that is replaceable or comes with the stalk. If you don’t have the manuals drop me your email and I’ll send you a copy. I think messicks (online store) has the microfiche/parts diagrams to look up replacement parts. I would also throw a post up on heavy equipment forum there are some knowledgeable and helpful folks over there.