How to Relip 3 Piece Wheels - Nikita's Work Rezax II's

No video

How to Relip 3 Piece Wheels - Nikita's Work Rezax II's

Рет қаралды 142,084

OffBeat Garage

Күн бұрын

Пікірлер: 161

@TopherHatch 7 жыл бұрын

Can't wait for another vid of your build. This channel is super underrated. Keep up the good work Man

@OffBeatGarage 7 жыл бұрын

Thank you buddy

@tyranwaltees9207 7 жыл бұрын

Just a tip when sealing anything, put down your sealant then spray it down with window cleaner ( this makes it not stick to your fingers) then use your bare fingers and smooth it out! 😃

@webwebber 5 жыл бұрын

Best video out here. Straight to the point and no hairdos. Awesome.

@myrondaniels5136 7 жыл бұрын

3 piece gang gang

@pikerdm7466 7 жыл бұрын

even tho you are planning on taking apart the wheels in a year i'd still recommend using purple threadlocker, purple is the lowest strength threadlocker it helps the parts hold together but can be undone by hand tool pretty easily.

@OffBeatGarage 7 жыл бұрын

Good to know, thank you!

@tarmokaupal5052 7 жыл бұрын

OffBeat Garage where is your own drift car?

@OffBeatGarage 7 жыл бұрын

In the garage, 30 feet from where I'm typing this lol

@JustinSmith- 7 жыл бұрын

All my work hardware had locking nuts. Although I'd recommend undoing the hardware from the back and torquing from the back. Those bolts are expensive lol

@DavidSciberras1993 7 жыл бұрын

i cant believe you missed the opportunity to make a brief shooting stars meme when disassembling the lip.

@iamawatermelon9299 7 жыл бұрын

David Sciberras dead meme

@Dorgie20 7 жыл бұрын

glad to see the content is back! keep killing it man!

@Shadowen925 7 жыл бұрын

That electric tire machine sounds so much better on the ears than the pneumatic ones I use all the time.

@ahamedkhan232 7 жыл бұрын

gang gang. Adel is back.

@mikemedeiros5458 7 жыл бұрын

Bring the old intro back, shit had me dying every time

@OffBeatGarage 7 жыл бұрын

+Mike Medeiros Hahha I need to make a new one! Old file is corrupt

@HksTopAndRock 7 жыл бұрын

Next time dip your finger in soapy water before smoothing the sealant helps it to glide over the sealant so it doesn't stick as much to the glove. 😁

@alabar9795 3 жыл бұрын

How to change lip. Undo bolts fit new lip fit bolts?

@goddamitgar8470 6 жыл бұрын

Always, ALWAYS spin the nut not the bolt.

@horrorhawk7320 4 жыл бұрын

why is that?

@scrub_lord 3 жыл бұрын

HorrorHawk i would imagine so you dont strip the bolt or the hole

@seansmile 7 жыл бұрын

I remember when you started and never did a burnout lol look at you now rebuilding wheels..

@kylebanta1903 7 жыл бұрын

Daaamn Nikita's rich homie! Rich gang gang!

@TheRuneCrew2 7 жыл бұрын

For real. Who buys a $500 dollar torque wrench?

@TheSupradude26 5 жыл бұрын

@@TheRuneCrew2 mechanics who use them all a lot buy expensive tools like that all the time. When I used to work on cars for a living I had tons of expensive tools. Plus the Snap-On truck showed up to every shop.i worked at every week so you can buy whatever you need, or they will replace or fix anything that is broken for their lifetime warranty, and all of our snap on dealers would give us 0% interest on anything we wanted. I would grab a few hundred to a couple thousand worth of stuff then pay him $100 to $250 a week. Even if things were tight or I didnt have the cash on me you could skip a couple payments with no penalty. Yea, Snap-On, Cornwell, Mac etc tools are expensive, but when you use them every day all day it's worth it. They are all so much better than anything you can buy in any store really... The 0% interest when they dont even pull your credit or anything cant be beat either...

@ryliegreen7997 6 жыл бұрын

Thanks for the awesome fast pace video guys..

@YoeriKurvers 7 жыл бұрын

one and a half million dollar tire machine

@shaun6437 7 жыл бұрын

More like 1 and a half million dollar set of wheels.

@babyxjesus5305 7 жыл бұрын

Yoeri Kurvers 1.5 million dollar tire machine😱

@KubaWicha21 7 жыл бұрын

Lol its probally not even 10k LMAO

@YoeriKurvers 7 жыл бұрын

If you don't follow his snapchat you don't get the joke 😂

@YoeriKurvers 7 жыл бұрын

Infandous Ktenology haha desperate? Why would i feel desperate if i follow his snapchat? I mean you're here watching his videos that's almost the same as watchen a snapchat. It's just a video of what's happening in his life. And Turbo douches? 😂

@alpalchevskiy3886 7 жыл бұрын

OMG so much work (no pun intended) if I had 3 piece rim, I would never take them apart... unless they are damaged or something

@Juniorrrrrm 7 жыл бұрын

Great video just what i was looking for! Now i just need to know how the offset works when you change out barrels or lips ! Make avideo on that!

@Moneygrip 7 жыл бұрын

He really wise dabbed on y'all when he turned the wheel

@xZoulos 7 жыл бұрын

when are new build videos are to be expected?

@BillyMOV 7 жыл бұрын

Should have run the 11s #hotboistatus

@Iain240 7 жыл бұрын

Damn i love this channel.

@DONTRAGEQUlT 5 жыл бұрын

1.5 inches is like 38mm why would it be 18x9.5+ 19 and not +38?

@gabenewell4582 2 жыл бұрын

because offset is measured from dead centre of the wheel not from the face

@ThisIsLife21 7 жыл бұрын

In class "fuck it d000d gotta watch dat new vid"

@shanejohnson9531 7 жыл бұрын

"don't get bloody, cut towards a buddy"

@Wrenchlife604 7 жыл бұрын

Good video just did a set of 2 piece wheels on my channel. always wanted a set of 3 pieces SUbbed!

@NYSIXFIFTH 5 жыл бұрын

Great job guys

@georgiohenderson5998 7 жыл бұрын

Would it make more sense to use the power drill on the inside of the wheel and wrench on the outside? I'd rather scratch the inside with a spinning tool than the outside of the wheel.

@OffBeatGarage 7 жыл бұрын

+Anthony Buscemi Can't reach it because the barrel has the drop center built into it. Take a closer look when I show putting the 10mm wrench on the back side and you'll see that fitting a socket there on a drill isn't possible. If it were, that would definitely be the preferred method.

@pocketsearch 7 жыл бұрын

I should really be in the garage rebuilding my wheels..

@djuanejackson4215 3 жыл бұрын

Great Job!

@915Performance 7 жыл бұрын

Notification squad!!

@Null__82 2 жыл бұрын

But u could take any three piece wheels and take theese apart, (no matter the method) and for example make it have more offset or less (deep dish/ less deep dish) right?

@DavidSciberras1993 7 жыл бұрын

Oi. almost crashed trying to watch your live stream. notification squad waddup

@OffBeatGarage 7 жыл бұрын

Hahaha

@ricotheunprofessional 7 жыл бұрын

David Sciberras don't watch adels live and drive

@basbeunhaas 7 жыл бұрын

F*ck yeah another upload! :)

@DMbros14 7 жыл бұрын

holy angle 👀

@godshammgod5792 7 жыл бұрын

you should go help my man chris fix and his project car

@JohannesKonow 7 жыл бұрын

Why would anyone need a 12 point socket other than for the occasional 12 point nut btw (of which we have extremely few in europe anyway)? They only thing I find them good for is to round the corners on six sided nuts and bolts (and they are super common, at least in my line of work).

@markusp9432 7 жыл бұрын

thanks didn't even know my rims had a lip like that

@popclutch_100 11 ай бұрын

I want build 20x10 front and rear work vsxx wheel. Offset +30 with 5" lip to be flushed with the fender and tucked. The vehicle will be bagged too. Should I do 5" lips or 6" lip? I was told the offset would be +30. Is this true?

@cleaned5772 7 жыл бұрын

Are those Nikita's 1.5 million dollar rims?????????

@carlfocker4092 7 жыл бұрын

hi, I'm using BBS RS slanted lips 18" 8.5. how do I make it wider to 9.5? I can't find the available barrel to buy

@RaceboyYT 7 жыл бұрын

Mohd Haikal blackforestindustries.com thank me later

@carlfocker4092 7 жыл бұрын

they don't have 18" barrel tho. but thanks mate

@LKGarage808 7 жыл бұрын

threepiece.us

@carlfocker4092 7 жыл бұрын

ayyyyyyyyyy thanks mate!!

@Marc-gm5cm 5 жыл бұрын

the 19 ft torque is for any two-piece wheels or just for this particular model? I just bought a speedline corse wheels and I want to remove it to paint them properly but I wanna be sure to what spec have the bolt to be tightened

@jdmcarboy64 6 жыл бұрын

Was that jingle bells you were trying to play with the hardware?

@miggydizon 7 жыл бұрын

im going to start rebuilding my 18 kranze erms. do i need to torque them bolts to the same amount when i put them back on?

@hmong337 6 жыл бұрын

I recommend a rubber wire brush to clean faster

@KevinSmith-xt8xr 5 жыл бұрын

What about a 2 piece welded wheel which is what i have , 15x9.5 ssr Watanabe

@theblakeslees7065 7 жыл бұрын

That's a lotta angle for the dangle

@cris5341 4 ай бұрын

Hello..screw/Bolts..they are iron or titanium?

@vela07 6 жыл бұрын

Could you relip my front work rezax to clear larger brakes?

@TommyBlazeHD 5 жыл бұрын

How come there was no weld in between the barrel and lip?

@theregoesmiller389 7 жыл бұрын

i do that same clap @13:35 hahahah

@mannyortiz4824 5 ай бұрын

I got spec-1 20" rims ..I want to take the steel lip out. Do u guys do that job.n how much

@TrueFunctions23 7 жыл бұрын

rich gang 😂

@chevycinco6654 7 жыл бұрын

could of used the tire machine to cut the glue off

@KanaRacingOfficial 7 жыл бұрын

Hey I wanted to order some cool Japanese drift mags but I dont know what or where to order any. Have any good suggestions?

@KrejciTom 4 жыл бұрын

Where can I get new lips for my Work Rezax 2 18” wheels?

@OpaApoPl 7 жыл бұрын

You didn't put any sealeant/glue at the edges of the tire? The man I'm going to for changing my tires always does that. Or is this not necessary? I have no idea about this.

@OffBeatGarage 7 жыл бұрын

What he's using is a tire lube to help with mounting the tire on the wheel. We also used a tire lube when mounting the tire. Although it is not necessary, just makes things easier.

@galapagosmonster5554 7 жыл бұрын

OpaApoPl they usually put that sealant just to make sure that the tire doesn't leak.

@chrisdold6296 5 жыл бұрын

y would you put a smaller lip on go big or go home

@pantomasz856 5 жыл бұрын

3tlg ❤️

@W333dm4n 5 жыл бұрын

so 2 piece is no good cuz you cant relip them to ur spec? its always gonna be inferior?

@Moneygrip 7 жыл бұрын

Be careful that's a 7 mill bench you're scratching up

@neu1113 4 жыл бұрын

Can you built one for a customer? I'm very much interested.

@anthonycruz8349 7 жыл бұрын

I'm planing on buying used vsxx wheels with a high off set. If I wanted a lower off set for a bigger lip, I can purchase a bigger barrel and achieve the look I want?

@OffBeatGarage 7 жыл бұрын

+Anthony Cruz If you want a lower offset then go with a smaller barrel and larger lip.

@lb9gta307 7 жыл бұрын

Why pull the barrel off if you're leaving it alone? Seems like extra work for no bennefit.

@OffBeatGarage 7 жыл бұрын

anytime the seal is broken it needs to be redone. So even though we only changed the lips, we still needed to take off the barrel and prep it for resealing.

@akmalps9999 7 жыл бұрын

dat clap tho

@Kris-cp3tz 7 жыл бұрын

How does Nikita have so much money?

@TheRuneCrew2 7 жыл бұрын

His dad is Vladimir Putin.

@OffBeatGarage 7 жыл бұрын

+The Scorpion He has a job lol how else

@Kris-cp3tz 7 жыл бұрын

I didn't know professional Hotboii was a real job

@TheAvihs 7 жыл бұрын

More info on Nikita tyre machine?

@TylerF30 7 жыл бұрын

Does the positive offset create the poke or is that how the wisefab set up works?

@OffBeatGarage 7 жыл бұрын

+Tyler Novia Wisefab creates a ton of poke.

@nullsker 7 жыл бұрын

Where can I buy new lips and barrels for my wheels and get them shipped to me?

@OffBeatGarage 7 жыл бұрын

Wheelflip.com is what we found to be the cheapest. threepiece.us as well as vrwheels sells lips and barrles as well

@1Krsna8 7 жыл бұрын

dope ass video

@OffBeatGarage 7 жыл бұрын

Ty fam

@hjibuloibgiol987 7 жыл бұрын

Saw you at Formula Drift on Friday, no camera gear though?

@OffBeatGarage 7 жыл бұрын

+hjibuloibgiol987 I don't record events like that usually

@hjibuloibgiol987 7 жыл бұрын

OffBeat Garage For sure, I can see why. Especially for qualifying rounds, it's pretty boring 😂😂

@nikita240s13 7 жыл бұрын

FIRST!

@ricotheunprofessional 7 жыл бұрын

Nikita Rushmanov y i can still see my comment huh nikita

@imhungrytoofoo 7 жыл бұрын

Nikita Rushmanov 1.5 million dollar comment

@OneCrazyMOB 7 жыл бұрын

what are the wrenches at 4:53 top right corner used for the colorful ones. are they just adjustable?

@OffBeatGarage 7 жыл бұрын

They are used for AN fittings

@ScollayTable 7 жыл бұрын

min 14 -15 #OffBeatGarage where does car sounds?

@Aron-ru5zk 7 жыл бұрын

Fucking hell holding onto the handle on the bead breaker can break your arm or rip your elbow out of its socket

@stylepoints.180 7 жыл бұрын

Tag 915 no it can't, use to work in a tire store and never had a problem

@hoseacoltes4756 4 жыл бұрын

where to purchase the lip new

@neu1113 4 жыл бұрын

Where do you get the parts?

@weallneedlove1263 7 жыл бұрын

Tip: never try unbolting 3 piece wheels without an impact gun, you get really bad cramps

@OffBeatGarage 7 жыл бұрын

+beeza copper Ohhh yes hahaha very true

@lukeybabes1 7 жыл бұрын

1:39 why does the mounting surface look so messed up?

@rosariosalinas3580 6 жыл бұрын

LukeyBabes mounting and unmounting over and over

@elliott9999999 7 жыл бұрын

torque spec says 19 lbs is that one ugg or two? Lol just seen a meme about that

@evanmastermind 7 жыл бұрын

two ugga duggas.

@FuckJayJayyy 7 жыл бұрын

#nakaisantipsandtricks

@christianserrano7344 7 жыл бұрын

Wtf! I missed 4 videos from you because you weren't showin up in my sub box. Fuck youtube

@applesyo 7 жыл бұрын

is this the three guys one sr20 from yesterday?

@OffBeatGarage 7 жыл бұрын

+Apples yo Nope that was live streamed on Instagram. This is from another time where we just relipped his wheels

@opelcorsa2012 7 жыл бұрын

#notificationsquad

@TheTruthBeToId 7 жыл бұрын

Why did I just watch this? and why is canelo worried about wheels when he should be training?

@rolexdzn6662 6 жыл бұрын

@mini_maniac4205 4 жыл бұрын

Anyone else hear jingle bells when he was drilling

@jovialvibes5962 7 жыл бұрын

the fitment lol

@Xxsharpshooter58Xx 7 жыл бұрын

these are like my dream wheels ! i just wished they made them in 5x100 for my subie

@cheapcharlie7 7 жыл бұрын

Hello from the other side I must have called a thousand times

@joewontwice 7 жыл бұрын

how long does it take to do 4?

@OffBeatGarage 7 жыл бұрын

+Nay Cee If you know what you're doing it'll probably be under an hour a wheel to go disassembly, cleaning surfaces, installing new lip, torquing to spec and then resealing. If it's your first time probably a little longer.