@@mariogca Click "more info" or send me picture.. but genneraly it will be on thr bottomright hand side next to the dut smoke
@Fireprotectiontech416 Жыл бұрын
Yea exactly what I was thinking, those devices are still out of service. I’m having the same issue at a site, there’s workers doing renovations and they’re taking detectors down and putting back up after work is done. Some smokes are not restoring to normal and staying in “No Answer”. I’ve tried many things, cleaned contacts, tighten base, ensure dip switches are correct, ensure wiring is correct along with voltage and nothing has worked as of yet. Wondering why they all of the sudden won’t restore to normal and stay in no answer.
@muktitamang69293 ай бұрын
Hello sir can you give more information for Esser IQ8 please
@mobinalam112011 ай бұрын
Hello
@raniz1973 Жыл бұрын
Lol, easier to disconnect the cables from the channel and do a warm start. All devices will become "normal" but you will get channel failure. But easiest way is just to shut off the power from the panel and you will have no troubles at all 🤦
@lifelikerun2358 Жыл бұрын
Excellent but vedio not clear
@rehanzahid54396 ай бұрын
But last you take exit from the menu of hiding all the troubles but at least you have to show when all troubles hide and panel shows Normal
@yingfaichong Жыл бұрын
If want to release all over hundred disable trouble of signal, is it same case and same way release the signal.🙏🙏
@manjeshishwar7195 Жыл бұрын
Hi sir How to sir manual add idnet address form detector to panel?
@MrrNat99 Жыл бұрын
Can you wash me about program addressable panel integlex
@user-cx6tq8sh1e Жыл бұрын
Plz help me how to remove, install mode active abnormal
@mobinalam112011 ай бұрын
Hello
@mobinalam112011 ай бұрын
Hello
@abdulkhayoom4083 Жыл бұрын
What to do two alarm active same time? Pls reply
@anilkolanchery Жыл бұрын
This same problem how to sove in simplex 4010
@satheeshchandran23 Жыл бұрын
Hw disable sonders &outputs
@rehanzahid54394 ай бұрын
But where trouble gone it appeared again
@user-lp3le1un7b Жыл бұрын
How to turn off the alarm sound permanently without shutting down the system
@MrSuper_416-jx1rsАй бұрын
You didn’t solve the problem, you just shoved it under the rug.
@IftikharKhan-jq5rj9 ай бұрын
Simplex 4010 OVERCURRENT TROUBLE how i slove plzzz any bady answer?
@johntherecluse51217 ай бұрын
There's a short in the system. It could be a device that was connected wrong and needs the right contacts.
@marcosnoguera69635 ай бұрын
One minute?
@user-uy9vy9sn9s Жыл бұрын
Liar your self,Trouble in system not cleared
@rehanzahid54394 ай бұрын
It's not an understandable video you didn't show us in last that all the troubles went hide
@ajaysingh1212singh-uq9ck6 ай бұрын
Very bad camra shoot but you speak good but vidio is not good
@AsifAli-nk7lm4 ай бұрын
This is not healthy
@ZeePirateMan Жыл бұрын
I have a common trouble point for node 2 card status fault. Any idea what may be wrong?
@Fireprotectiontech4169 ай бұрын
Have you checked the batteries? They come up as that but also should have a battery charger/depleted trouble so I’m sure that hasn’t gone over your head. Maybe ground faults? If not try a full panel reset cold start