How To Remove Brake Drum On 2006 Ford Focus

Рет қаралды 77,636

7 жыл бұрын

How To Remove Brake Drum On 2006 Ford Focus, quick video on how to remove brake drum, hope this helps. Link to puller below.
Tools Used:
ABN Axle & Front Wheel Hub Puller: amzn.to/2WzsEiX
CRAFTSMAN Breaker Bar: amzn.to/3l1XzO7
1/2-inch Power Electric Impact Wrench: amzn.to/3A3GhVl
Film Gear Used:
Blue Yeti USB Mic: amzn.to/2GnK4Dl
IPad Air: amzn.to/2Exopb8
Soft-box Lights: amzn.to/2Ezg6M3
AMIR Phone Camera Lens: amzn.to/2EwpT5K
GoPro HERO3+ amzn.to/2QfBAGp
Editing Equipment:
Dell Latitude E6420 Laptop: amzn.to/2SHZc3I
MacBook: amzn.to/2yjlLma
Zelotes Mouse: amzn.to/2LKwJJQ
Cyberlink PowerDirector 17 Ultra: amzn.to/2S2wFqS
Contour ShuttleXpress: amzn.to/3amkISO
Stay connected:
Instagram - / channel.ron

Пікірлер: 32

@nathanewing1978 11 ай бұрын

Puller is the only way to get them off if the bearing is stuck, Thanks for the video!

@ryanbianchi6582 4 жыл бұрын

“Just like that” thanks Ford for creating this. Other manufacturers drums just come off 😂

@musicauthority7828 2 жыл бұрын

Goes to show how much you know, quite a few manufacturers have drums quite similar to that.

@nomadsteve5297 4 жыл бұрын

Thanks for posting this straight to the point and very informative video 👍

@svtsuperveloce8559 10 ай бұрын

Thank you i was looking for this specific vid life saver 🍻🍻👌🏼👌🏼

@channelron3593 9 ай бұрын

Glad it helped

@louislamboley9167 5 жыл бұрын

Thanks

@channelron3593 5 жыл бұрын

Your Welcome! Glad that I could help

@musicauthority7828 2 жыл бұрын

I would really like to know where you got that puller. mainly the head assembly that goes on the lug studs. I already have the rest of the components I have been looking for one of those for quite some time, any assistance would be helpful thanks in advance.

@channelron3593 2 жыл бұрын

Sorry about that I will put in the description amzn.to/3itvrSn

@musicauthority7828 2 жыл бұрын

@@channelron3593 Thank you so much I will check it out.

@joehyundaitech7961 6 жыл бұрын

are you sure the socket size is a 29 mm? my 03 focus is a 30 in the rear

@channelron3593 6 жыл бұрын

Not sure? I am thinking that is what I used but maybe I was wrong, could be the years may be different, Thanks for watching.

@silkysmooth9515 4 жыл бұрын

No Channel Ron is right one I'm working on is 29mm as well!

@joehyundaitech7961 6 жыл бұрын

where did you buy your puller ? I want to buy one

@channelron3593 6 жыл бұрын

Amazon for about $20.00www.amazon.com/OEMTOOLS-27037-3-75-Axle-Puller/dp/B004FDMWE0/ref=sr_1_6?ie=UTF8&qid=1526462603&sr=8-6&keywords=hub+puller

@cocodog85 3 жыл бұрын

folks HELP!...my drum is seized to the axle shaft at the wheel bearing. the wheel bearing is inside the drum hub. my drum puller broke because of the torque used to try and remove the drum. any thoughts? i used a small hand torch to heat the bearing sleeve. it didn't work. what should i try next?

@channelron3593 3 жыл бұрын

Sounds like the brake adjustment is holding in on? if the puller is not working? not sure

@cocodog85 3 жыл бұрын

@@channelron3593 . the bearing is welded to the spindle, some how. i took the whole assembly off by removing the spindle from the backing plate. replaced the spindle with a used one, new shoes and drum/bearings. a lot of trouble for a normally two minute job. i smashed the old spindle a few times with a sledge hammer but it is still stuck in the drum. i put some grease on the replacement spindle to avoid a repeat welded bearing.

@paulg.celentano5739 2 жыл бұрын

@@cocodog85 Nuthin' like 10 pounds of steel on a stick!

@cocodog85 2 жыл бұрын

@@paulg.celentano5739 never was able to separate the two. the item went to the recycler.

@mariogomez4359 3 жыл бұрын

What if I don't have a puller?

@channelron3593 3 жыл бұрын

Umm, (: guess you could put a pry bar behind and maybe work it out?

@warrenpeas Жыл бұрын

they never show how much muscle it takes to remove the 29mm nut. good god

@mlbjr 5 жыл бұрын

This is not the preferred method for this vehicle. You should just remove as the workshop manual states. Remove the drum and bearing assembly as a unit by removing the 4 bolts behind the backing plate. This eliminates the need to replace the bearing, exposing the spindle, and replacing the hub nut.

@channelron3593 5 жыл бұрын

Thanks for the info I will try that the next time I need to remove it.

@VideoServicesLI 5 жыл бұрын

Pulling the 4 bolts won't work on a 2010 focus unless you want it all in your lap - be careful what year you do this on.

@chuckadams5565 5 жыл бұрын

The manual states this, but at least on my 2004, the brake lines are in the way of the bolts so it's not practical at all.

@smoberdeen 4 жыл бұрын

It may depend on the model year because the bearings and studs are already installed on the replacement drum for the 2010 Focus. www.autozone.com/brakes-and-traction-control/brake-drum-rear/duralast-brake-drum-22116/315959_0_0

@tommy_2_trill 4 жыл бұрын

This is basically how I am going to have to remove my drums because my rear driverside bearing is shot and has fused to the drum housing.