No problem I'm glad you enjoyed it

haha, agreed!

I'm in the same situation, I hope this works for my 1950 windows.

I know this is 2 years old, but how did it work out? Any updates? Thanks in advance if you see this.

@@TheNarrowPath84 the process worked perfectly for me, but I didn’t put in a set screw, I just tapped around the edges to curl the metal over to stop the bushing coming out. Like he shows in the video. But I used the end of a flat file to gently hammer the lip over, instead of just hammering directly on the metal.

@@AfricanFlightStar Thanks my friend. I have some windows in my house I need to work on so thank you for the info. 🙏

Thank you I'm glad you enjoyed the video. Thanks for calling and resourceful and not off crude. Good luck with repairing your cranks. If you have any questions feel free to ask me in the comment section. Thanks again Bobby

I agree these windows are tricky

I'm glad this worked out for you and became a success. I am also happy to hear when people tell me they have saved money but doing a project thanks for being part of GetGo TV

I know the feeling. When I fixed the broken window I went to close the venitian blinds and they did not close. So I had to fix them. Lol.

Hope it helps

Only need to drill the hole deep enough so that the screw will prevent the shaft from backing out

I agree this design definitely sucks

Did you ever figure it out? I was thinking of just using a smaller self tapper. You can get them at the hardware store instead of having to drill a hole and use the set screw. You could still use the set screw in the appropriate spot. Let me know how you ended up doing it? Also, I don’t think it matters where you put screw. (I think a self tapper would look nicer. Just my opinion tho)

I got the same problem with my window

@@danlivni2097 I think this might be my problem, too. I'm going to see if a thin layer of caulk on the stem might make the window a little more usable.

+Island Gaming no problem glad you like the video

No I don't replace the screws from the handle. A lot of people leave those off anyway because they have Colonial blinds and the handles have to easily be removed to be able to close the blinds

+Jason Schade jb weld cracks

+Jason Schade. Epoxy would work I'm pretty sure. But what I was showing in the video was had to fix the operator without any material for what was there

@@-GetGoTv So I can put some epoxy on the end of the worm drive and stick it in instead of drilling?

If you look close at the actual crank, you will see that is exactly how it was assembled at the factory. The cowling is a press fit over the part that turns and it just wears out so much that it gives way. I have done this exact fix on 4 of them already.

The rubber weather sealant gasket around the outside frame of the window has swelled with age and moisture and no longer allows the window to fit tightly in the casement. If you were to remove the weather sealant gasket and replace it with a new one, the window would close until that gasket started to disintegrate five years from now. At the end of the season, I go outside and push all the windows closed for the winter. Between spring and fall, those windows are never closed properly. If you have a twin window set where two open next to each other from the center out, never open on of those windows except to help close the other one. That saves that window from deteriorating with the weather. These windows are not all they promised when they were new.

Actually a solution to a big problem more like classic problem solving . I don't Gerrit rig anything

Email me a picture of what the problem is with your window the email addresses Peninsulaimp@gmail.com I will look at that picture and tell you what I think

If it is the arm with the wheel on the end that goes under the window that opens and closes and it pops out of the track that goes Under the window part that opens and closes you can bend it upward and then place it back in the track This will keep tension on it so that it doesn't pop out

@@-GetGoTv thank you so much!

this video was taken at a client's house . I have done this at dozens of homes in a gated community and everyone was pleased with the repairs

+Katie Stewart let me know if you have any questions I'll be glad to answer them

Are the locks on the Windows disengaged? If so and they are unlock the windows might be stuck this happens a lot. I use a 5 in 1 tool insert it in the crack on the opening side of the window and move it back and forth while gently pushing the window to get it unstuck. Then push the window while cranking

Actually the window does close completely the same as any other windows that has a functioning operating crank. There was a crack in the window because the window was not crank completely closed in the video and the locks were not engaged. The cost of a window crank operator is $55 but I have done this repair on Windows that have passed home inspections on a real estate transaction eight years ago and the window still functions and closes tightly. Also before the repair the crank did not function at all on the closing side. I have done at least 30 windows like this and all function perfectly. Perhaps you should try working on Windows and window cranks before you make a judgment and comment

+NYC Babydoll7 You are exactly right this is a very good point.BPA is said to mimic the structure and function of the hormone estrogen (2). Due to its estrogen-like shape, BPA can bind to estrogen receptors and influence bodily processes, such as growth, cell repair, fetal development, energy levels and reproduction. In addition, BPA may also have the ability to interact with other hormone receptors, such as thyroid hormone receptors, thus altering their function (8). Your body is sensitive to changes in hormone levels, which is the reason why BPA's ability to mimic estrogen is believed to affect your health.

Should have just bought a new crank. That's what I'll do

The crank is not the problem. The axle guide (for want of a better term) is coming out. He drove it back in, drilled a hole and put a set screw in to stop it as well as peened the edges. Looks like it works fine. Ingenious.

You may be surprised, but this exactly how this crank is assembled. It is a bad design. I've fixed about 5 around my house with the same fix. The crank is a piece of crap.

The screw that holds the handle on is insignificant. The handle will not come off unless it is pulled off. A lot of people pull the handles off and place them in the windowsill because they have Colonial shutters that will not close with that handles on the window. A lot of people just take them off. The screw that's a perfect kind of screw for this. To use a different screw more than likely you would not have the type of screw necessary and would have to go to a hardware store. Therefore is it sensible and practical to repurpose the screw that isn't necessary because the handle stays on by itself without falling off unless you pull it off

I'm glad you enjoyed the video please subscribe to the channel thank you Bobby

You should try watching the video in slow motion and count how many times it slipped out and then you will know

Glenn I'm wishing you all the luck. . Step back from it for a minute. Take a deep breath A couple of times and let that anxiety go away. Also Check your weather stripping around your window. And make sure that the Window is not stuck Which could make it even worse. Check to make sure that it's not painted shut. Once you get the crank fixed Push the window with your hand the first few times. Help it open. And pull it To help it close. To get it used to opening And closing again. If you have any questions. Just leave it. In the comments section and I will return an answer to help you through this. You got it, man. I know you do.

@@-GetGoTv Thanks so much for the reply,,,,it worked like a charm:):) Thanks so much and I didn't even smash the glass which I was afraid of because it's so cold here in eastern Canada. You made it look so easy and I'm so proud of myself. I'm so happy I googled and found you. Thanks again so much, I truly appreciate your skills!!!! Happy Sunday:) Best subscribe ever!!!!!!

+Jeff Woods I hope this was helpful

it was thanks...I didnt do the bending over with the hammer bit, but i used the screw from the crank. i am always looking for ways to keep impressing my wife...Im a hero again now.

What would you make the title? Hope your project turns out well

Not true. the only thing you see is a little screw head. I have done this for dozens of clients, and they were all happy. The repais lasts and is a lot less expensive. This particular window was discontinued and the new operators have to be ordered and installed by a person approved by marvin

When you turn the crank to the right the window works perfectly the problem is though that when you turn the handle back to the left the inside of the operator that has the threads on it backs out of the crank. You do not have to push the handle in when turning it to the right. Pushing it in when turning it to the left will not stop the threads from backing out of the hole. The housing on the operator is made of aluminum. When you tap the edge of the operator it cramps it over the edge to prevent it from backing out however this step alone is not enough as it will eventually back out anyway. that is the purpose of the set screw. I have tried washes and many other things over a course of several years on 32 town houses that have these windows Marvin Windows and some are credco windows. After the repair in this video there is no need to push the handle in when cranking either right or left and I have Windows that I did this repair on 8 years ago that are still functioning properly. The second option would be to replace the operator which runs around $45. I have no problem replacing it as it doesn't take that long to do however some people don't want to wait or spend the money so we came up with this hack for the crank that works perfectly also there's nothing to hold washes in if you put them there the handle with a set screw will not hold the washer is down because the handle is hooked to the shaft that has the threads on it so when the threaded piece with the shaft backs out the handle comes back with it. This leaves only has the option of a set screw which would probably be enough. The only reason I crimp the edges over is for a little extra insurance

Warehouses usually don't have Windows unless they're new ones in boxes to be shipped . The repair shown in the video does not make the crank look bad.

You can buy replacements if you want. They cost at least $45 and up. Me? I'd rather do what this guy did and save my money. So glad I found this as I just bought a house with about 10 of them that need repaired

@@-GetGoTv Thanks for this video!

That's right they really work well

+matthewweott you're right it is and it works really well too

Might be what you call it but it works great. Perhaps you should share some of your Genius ideas

Definitely can't buy a Marvin casemaster window at home depot. They don't make them any more . This repair is permanent and was done years ago and still works perfectly today. You should know what you are talking about before you make a ignorant coment