very very thanks I repaired 4 LED bulbs in just 30 min thanks
@anuraggoswami287 ай бұрын
ये ज्यादा दिन नहीं चलेगा, बहुत जल्द दूसरा और फिर तीसरा और एक एक कर सारे एलईडी बंद हो जाएंगे। कारण? इन एलईडी को जलाने वाला सर्किट एक निश्चित मात्रा में करंट और वोल्टेज इन सभी एलईडी को देता है। आप जैसे ही एक एलईडी हटा कर वीडियो में बताए गए तरीके से टर्मिनल को शॉर्ट करेंगे, दूसरे जितने भी एलईडी हैं उन पर लोड बढ़ जाएगा और कुछ दिनों में ही एक एक कर सारे खराब हो जाएंगे। इसलिए एलईडी निकाल कर टर्मिनल शॉर्ट करने के बजाए एलईडी के बराबर का रेजिस्टेंस लगाएं उस एलईडी के स्थान पर। तब शायद एलईडी कुछ ज्यादा दिन चले।
@m.s.r.987 ай бұрын
Right 👍👍👍
@vikramsingh-iy5vd7 ай бұрын
Bhai led ke place pr kitna resistance ka kya lagaye agr 6w ka led bulb hai to
@raonitesh4206 ай бұрын
❤️ ❤️ ❤️
@diyhard6666 ай бұрын
@@vikramsingh-iy5vddu kannst den Widerstand einer funktionierenden LED messen
@shortviralvideo6696 ай бұрын
Yek dam sahi bole
@grabinfo10 ай бұрын
Thankyou I applied this concept successfully 😁
@Agriculture_luv3 ай бұрын
But after that i was heating why do that happens
@mahendershaw95472 ай бұрын
Heating issue 😢
@rawvoicelovers673210 ай бұрын
Yeh mast tha guru 👍
@EnricoWack2 ай бұрын
Buy a resistor and solder it on. Very easy and very cheap. Fixed many untill they are so dim practically a night light(also usefull)
@valpuiatrazerschhakchhuak968322 күн бұрын
Can you tell me the resistor colour code u used?
@EnricoWack22 күн бұрын
@@valpuiatrazerschhakchhuak9683 well mine was CFR25J-8R2. But you will need to check the voltage of your specific bulb as they do differ usually 12/24/48v and then the current each LED draws (milliamps) to select the best fit. Ill give you 2 different ones that should working..worst case it just pops if its too weak. CFR25J-8R2 or CFR100J-1R0.
@vvhh95785 ай бұрын
Repair and reuse can reduce waste garbage stock piling....thanks for sharing
@gwahs12459 ай бұрын
power of foil paper
@kdrlbndang2832Ай бұрын
Can i connect the bulb directly to the main electric circuit and repair it ??will it led to short circuit?? Or we should use battery while reparing???
@jimpyu10 ай бұрын
but that will create semi overload frying the other leds in the long run.
@ClickClack_Bam8 ай бұрын
Yes but you've saved money in doing this because you didn't replace that bulb you've extended it's useful life.
@SwapPartLLC7 ай бұрын
@@ClickClack_BamUntil the tape loosens up from the heat and the intermittent contact creates enough heat to start a fire. Better to replace the bad LED with a zener diode.
@ClickClack_Bam6 ай бұрын
@@SwapPartLLCTo be fair, I didn't say it's the best fix. Imo he could replace the led with another led. Probably the best fix would be to take a burned out bulb & cannibalize it by using the same LED's from the burned out bulb to fix other burned out bulbs.
@SwapPartLLC6 ай бұрын
@@ClickClack_Bam That's a lot harder than you think. The circuit these are on is bonded to an aluminum backer. You have to heat that aluminum from the back in order to remove the LEDs. It's the same process I used to use when I did LED repair on TVs. It's easy enough on the one you're cannibalizing for parts, but the one you want to save now has to be disassembled. I was playing with a couple of these last week. The wires use push connectors, and they're pretty much one time use. If they pull out from the socket side, it's pretty much over because you can't get the wire back in. I suppose you could probably swap out the stranded wire for some 20Ga solid core like thermostat wire, then maybe you could get it back in. In my experience, the push connectors break if you loosen them. So, you would probably have to solder the wires where they go into the circuit board. It could be done, but it seems like a lot more work than it's worth. The reason I suggested a Zener diode is because it has the same characteristics as an LED (minus the light), and you could do it with a soldering iron from the top. The old LED can be removed in a destructive manner from the top.
@VikasBharti025 ай бұрын
@@SwapPartLLCInstead of a zener diode, can we use a simple resistance? If yes, how to calculate the required resistance? Will it be R=V^2/P ??
@migarakatugampala23585 ай бұрын
Success but finally I remove every small bulbs😂 thanks
@AriyanAhammedDelour19 күн бұрын
ভাই আপনার ভিডিও দেখে আমি নিজেই আমার একটা নষ্ট লাইট ঠিক করলাম এই মাএ😊😊 অসংখ্য ধন্যবাদ ভাইয়া আপনাকে ❤❤
@Ajaysharma00755 ай бұрын
You made my day bro … it worked absolutely fine
@donajmath3 ай бұрын
It works but detach due to heat. Soldering is best option
@SwapPartLLC7 ай бұрын
Seems kind of dangerous. Tape will losen up as it gets hot. Then, you end up with a bad connection. Bad connections create heat and arcing. Now you have a fire hazard. Better to use a zener diode to replace the bad LED.
@Ratnovai10 ай бұрын
Nice it works thank you very much 👍👍👍👍👍👍🤝🤝🤝🤝🤝👌👌👌👌👌👌❤❤❤❤❤
@raushankumarjha882210 ай бұрын
Use diode,so bulb can last longer
@suryakantsonkar60899 ай бұрын
Diode ka value bta do
@Kuanos_9 ай бұрын
@@suryakantsonkar6089other comment has that is should be 1 watt
@VikasBharti025 ай бұрын
@@Kuanos_the resistance is not measured in watt
@Kuanos_5 ай бұрын
@@VikasBharti02 your right, I didn't see as a resistance and how do you consider the quantity in ohms?
@VikasBharti025 ай бұрын
@@Kuanos_ Check number of LEDs in the bulb. If a 10W bulb has 8 small LEDs inside, and it is designed for 220 volt supply. Then using P=VI=V^2/R Therefore, Calculate R=V^2/P So R= 220x220/10 = 4840 Ohms for 8 small LED bulbs. Per bulb resistance = 4840/8= 605 Ohm It is generally safer to use a 1000 Ohm resistance i.e. 1K Ohm considering the availability. Otherwise, try to use the resistance of exact amount.
@Kabutar_king8Ай бұрын
Pet ki jagah pencil ka istemal karna tha
@behzadmodabberzadeh80147 ай бұрын
It works! Thanks a lot! You are wonderfull!
@DD-ms8gc9 ай бұрын
Bulb lagane ke liye jo holder banaya he wo series me hoga ya Direct AC supply me hoga ????
@JahangirKhan-bk1hs9 ай бұрын
Direct bhi chalega
@papuali1516 ай бұрын
Thank you good idea
@BChirgun-sm5pj9 ай бұрын
Thanks for informing
@MC_Alaba8 ай бұрын
Easiest technique ever
@aadhinagendraurviti58299 ай бұрын
Good Technic..
@abdulwali50909 ай бұрын
Really dis trick was amazing
@SajjadAli-lf6fd11 ай бұрын
Good information ❤
@tik4su4 ай бұрын
Thank you so much, I just fixed my bulb.😀
@user-yx8qb3mq7i10 ай бұрын
Great 👍😮
@user-oe4lr9xs1r3 ай бұрын
Thank you very much
@yondaime0user9 күн бұрын
that is quite risky for a dollar price tag
@RanjeetKumar-zh8eh10 ай бұрын
Thank you ❤
@JairoSoto-im3gkАй бұрын
👍👍
@tonydrake8179 Жыл бұрын
What resistor should one place when by passing one led, if it's not done the others will be brighter and burn faster
@ox_.stifff11 ай бұрын
Chalega
@syed_ayaan10 ай бұрын
If you do this what shows in video your led bulb will not work for long time burn too fast If u replace 1watt resistance in led place then it will work.
@BHIKARI-PAKISTANI-PM9 ай бұрын
1k ohm
@enchantgamer19409 ай бұрын
@@syed_ayaanhow do i know its 1w resistor 😫
@gyanklote1118 ай бұрын
I done this but my electric bill is thrice 😢
@radomihasina61975 ай бұрын
Thanks a lot, it works. Very useful tips 🙏
@JamMC4 ай бұрын
Lamp not bulb.
@belissonlighting13565 ай бұрын
nice and useful video❤
@jstranger55847 ай бұрын
I would have just used the other bulb🤦♂️
@vikaskumar27585 ай бұрын
Humane bhi try Kiya but no results
@rkbhiwani19476 ай бұрын
Real trick 😊😊
@khairulislamshakil79393 ай бұрын
১০০% কার্যকরী। আমি কেবল করলাম কাজটা।
@JinshuoDing11 ай бұрын
good way
@Happy3141510 ай бұрын
The idea is good, but the way you handle the bulb with electric on is dangerous
@VirtualPiano15 ай бұрын
I just tested it and it world , thanks for the video
@VirtualPiano15 ай бұрын
it stopped working so I used soldering iron instead
@Islamic_Beatz3 ай бұрын
Aluminum kaha se milega please reply
@ramsharma56242 ай бұрын
Bahut khoob
@jayprakashmishra88008 ай бұрын
🎉बल्कि सभी ledधीमी जलती है टच करने पर कैसे बनाएं
@VikasBharti025 ай бұрын
Jisse bhi sabse tej jale wo lgao
@vijnvij61272 ай бұрын
Thank You light on ho gai
@dheerajyaduvanshi17184 ай бұрын
Kharab led hatane k bad 220 ohm ka resistor lgaye tab kuch din life badhega bulb ka.
@HillBillyBarry20004 ай бұрын
Use wood stove flue tape its aluminum sticky tape. I just thought of it watching this.
@muruliam62413 ай бұрын
Superb
@user-de9jz7st1gАй бұрын
Isko direct ghar wali line se jod sakate hai
@SumanDevi-pr3cr2 ай бұрын
Bulb toh thik hua nhi wire aur ktwa diya 😅
@qalabeabbass282911 ай бұрын
nice 👍👍👍👍👍👍👍 Weldon🎉🎉🎉🎉🎉🎉🎉🎉🎉🎉
@amitraghav84507 ай бұрын
Thank u so much brother ❤I also fixed my LED bulb as per your video ✌️❤️
@Mani657724 ай бұрын
Bro led nikalna ka baad wo silver rang ke sheet ka kiya name tha?
@Athelxtan3 ай бұрын
@@Mani65772aluminium foil paper
@lakshyaparihar68573 ай бұрын
So are they in a series of resistance
@noorkhatun4707 ай бұрын
Main Aaj 2 saal purani bulb ko thik ki hu aap ki is video ko dekh ke 😅concept successful 🎉😂
@LEGEND_60707 ай бұрын
Ye sach me work karta hai ?/
@alicoolpoint1536 ай бұрын
Abhi chal raha he yaa band ho gya 😅
@eswaramurthys6902Ай бұрын
Very. Smart
@muazurabiu98128 ай бұрын
Is this really working?
@tik4su4 ай бұрын
Yes I just did mine, took some playing as you need steady hands 😀, but it's working.👍👍
@Target_Success5 ай бұрын
Good idea
@abutalhamolla20812 ай бұрын
wow nice
@anilpandit78729 ай бұрын
😮 mast
@kharwarritik69864 ай бұрын
Bhai jada din nh chalega ek ek kr ke sara led band ho jayega Aisa batao jo ki led hi badal de taki jada din chale
@liberatoybanez29849 ай бұрын
thanks.....
@ToThePoint6904 ай бұрын
Some time inside ballast is bad.
@RahulYadav00525 ай бұрын
Thank you so much
@VinodGautam-jq1on2 ай бұрын
सर सफेद कागज लगाया है क्या
@SohidulIslam-lc7vi10 күн бұрын
😊😊😊
@Girish30094 ай бұрын
Thank you❤
@user-oc5gj7ze8k8 ай бұрын
Use this pepar name please sir
@user-oc5gj7ze8k8 ай бұрын
Please reply
@SuperMicro-nm7px8 ай бұрын
Silver foil paper available in general kirana store
@hanifshaikh460825 күн бұрын
Plus minus kaise pat lagaye?
@Krishuko Жыл бұрын
First comment🎉🎉
@migarakatugampala23585 ай бұрын
My led bulb was not work then i repair it by watching this video then it work after repair it again its not working then I repair it again but finally I remove all the bulb due to unwork problem then I put into dust bin😂😂
@Natureportrays4 ай бұрын
I just did this and it worked 😮
@rajamallurachakatla44163 ай бұрын
Instead of repairing LED better buy new one it costs sum 100₹ only. Repairing is sometimes dengerous also, I was abroad Dey never repair, replace part.
@wckfrenando73039 ай бұрын
❤❤❤
@PinkBee-px5xh11 ай бұрын
This is only for 15 minutes 😂
@vijayahirwar65564 ай бұрын
ये कोन् सी पत्ति लगाया है
@harshitasingh11174 ай бұрын
It works ❤😊
@user-ut4mo2xk6z2 ай бұрын
It is very danger 😮😮
@shashiranjanofficialkks74734 ай бұрын
Current bhi dena hai
@malayghoshdastider16515 ай бұрын
Difficult to open upper part
@viras1413 ай бұрын
Nice
@DavidScaggs3 ай бұрын
I can't get it to work.
@AyushGuptaofficial049 ай бұрын
hiting problems nahi hoga na 😢😢
@debadritas_art5 ай бұрын
Maine Kia to ek chorke ek lite on ho raha hai
@snchongloi158011 ай бұрын
only problem is it won't last
@malikhassan35836 ай бұрын
Bhi ye pepar ka name kia ha are kha se mile ga
@rifasumai46998 ай бұрын
just fix the resister
@sachingite891411 ай бұрын
Do din se jyada ni chalega Ek led nikal Dene par kyuki sab led series me hai bhai
@marvelmovies5811 ай бұрын
Chalta hai bhai mene khud kiya hai one week se jyada ho gya
@sachingite891411 ай бұрын
@@marvelmovies58 bhai mai khud electronic tech hu kabhi kabhi driver se kam voltage aane ke karan chal jata hai lekin led ya plat badal Dene par sahi chalega
@syed_ayaan10 ай бұрын
1watt resistance lagado us jagah pey phir 1year ki gurrantey dio it will work
@sachingite891410 ай бұрын
@@syed_ayaan resistance value
@BHIKARI-PAKISTANI-PM9 ай бұрын
@@sachingite89141k ohm
@shuvomelodioussongs16944 ай бұрын
Mashaa-Allah 😂😂😂😂😂
@nehagarg23569 ай бұрын
It's not working
@MAbIslamic786media5 ай бұрын
Ye apne konsa silver paper astamaal kiya h
@kabirkhan97865 ай бұрын
Aluminium foil
@kabirkhan97865 ай бұрын
Aluminium foil
@DigantaChetia-cu4seАй бұрын
nice
@echaferdiansah3842 ай бұрын
Pakai kertas apa itu
@user-bs1sk3fz1h7 ай бұрын
Good
@starshine519 Жыл бұрын
I̲t̲'̲s̲ w̲o̲r̲k̲ 🎉🎉🎉🥳🥳t̲n̲x̲
@user-uc1fc2ls6c7 ай бұрын
😊😊😊😊
@tcfdesilva176119 күн бұрын
When bulb is heat what happen you are repair.💡 buld.🤔🤣🤣