HOW TO REPLACE A CUB CADET LTX1045 DECK BELT.

Рет қаралды 50,866

Жыл бұрын

Пікірлер: 36

@Ky-Alf 4 күн бұрын

I was watching your video, I picked up this mower cheap and needed to replace most of the springs and belt, your video helped showed the location and how to install new-belt, and springs which I have. Great job on video I followed it completely worked like a charm. now good to go! thank you very much:)

@Srt8Jeep Жыл бұрын

I had an extra spring when I reinstalled my deck. 😂 Thanks to your video I figured out where it went!

@VickiMcKeen Ай бұрын

Thank you for the video. I had an issue with a pulley and you helped me with that.

@DougHall65 Жыл бұрын

Thanks, Jason. Very helpful.

@bryanscheeler Ай бұрын

Thank you this was extremely helpful

@boogaloo62 9 күн бұрын

Thank you

@edhartman2860 Жыл бұрын

I was looking for a video showing the removal of the spring and engaging cable.... Thanks, it looks like I can do that...Good video...I have the Cub Cadet LTX 1042, same set up...

@justinsweet2028 Жыл бұрын

Glad it helped

@mybrass41 2 ай бұрын

So clear! Thx!!

@1randyful Жыл бұрын

At 11:00 minutes you show the 'L' bracket' under the idler pulley, being mounted on top of the main mounting bracket. It should be underneath that mount being held by the bolt that holds everything together. the short side of the 'L' should be touching the deck.

@rogerdodger1831 Жыл бұрын

Thanks for the video, is there any adjustments to make the belt a little tighter ? I just replaced the same belt with the correct part number ,it's flopping more than it should ,

@michaelbarcz326 11 ай бұрын

Dude ya gotta get someone - ANYONE to hold that phone

@aaronwism Ай бұрын

Tripods are cheap!! 😂

@sissymurphy9620 Жыл бұрын

3 screws on each deck belt cover as grass will push the cover up that gets caught under them . The new cub cadest at least have the new covers that don't allow that to happen They are metal and have openings to allow grass to be pushed out . I am having problems with the belt coming off and the screws to the belt holders keep coming down and rubbing on the pulleys . I ordered the new covers for my 2016 cub cadet hydrostatic since the screw holes match it . I am hoping that will solve the problem of the belt coming off while mowing . I also had to level the deck side to side

@beerleagueeverything8030 11 ай бұрын

Are the covers just to keep the user from stepping or knocking something into the pulleys and damaging them? Half tempted just to keep mine off. I get the grass build up as well.

@sissymurphy9620 11 ай бұрын

@@beerleagueeverything8030 if you take the covers off the belt keeps coming off . I tried it and belt kept coming off , The metal posts in the covers hold the belt . I hate the plastic covers as they just hold grass that is hard to get out . But found out not as much grass got stuck under the covers when I changed to gator blades and cleaned the underside of my deck and applied slip plate graphite to keep grass from sticking to the underside

@beerleagueeverything8030 11 ай бұрын

@@sissymurphy9620 thanks!!

@sissymurphy9620 11 ай бұрын

@@beerleagueeverything8030 your welcome and plus I ruined 1 belt by taking the covers off . So glad I could help . Try slip plate graphite under you take I have been a fan of it since my son who owns a towing company uses it on his flatbed tow trucks . It is a little expensive for a quart but 1 quart will do 2 lawnmowers and lasts for years and that is doing 3 coats and still some left over so did mny push mower and still sme left . I got my can on e bay

@kostia1975 11 ай бұрын

ltx1042 I replaced the idler pulleys with new ones, and after tightening them, they are not loosely spinning, is that normal?

@stevendiffy768 3 ай бұрын

What clip did you use in place of the bowtie clip?

@justinsweet2028 3 ай бұрын

Hair pin cotter key looks like a R

@user-xv2qf2vs7k 7 ай бұрын

Show me how to tighten the belt

@mytruthslays1303 Жыл бұрын

Why is there no tension on the belt?

@RicardoBigTime 10 ай бұрын

Your your attention comes when you actually activate the blades while you're riding that's what pushing that lever forward does

@LolethaBoyd-ct9dz Жыл бұрын

Belt keeps jumping off

@user-nd5bx8fk6v 3 ай бұрын

We have Mulch Plug that may fit your lawn tractor. We can provide for free. Do you need?

@michelboisvert5684 Жыл бұрын

hi, before working on your machine, wouldn't you like to clean it instead of working in dirt, because it would be much better

@justinsweet2028 Жыл бұрын

You absolutely can clean it / wash it but then you getting nasty water all over ya little dirt never hurt ya

@RicardoBigTime 10 ай бұрын

What size built isn't because there's no way in hell the 42-inch that I got reaches. It looks like it should be 60 to 80.

@nathananthony2552 10 ай бұрын

Ya, I bought the belt for a 1040 ltx but it's too small or I'm not doing something right.

@ashriver7710 10 ай бұрын

@@nathananthony2552the 42" measurement is the size of the deck. Ltx1040 takes a 96" belt I believe

@barbwire4879 Жыл бұрын

Dam. I said. ,46 in not a 42. Dam you tube

@coachtyler_ Жыл бұрын

A lot of skipping

@stanbryant7360 Жыл бұрын

try cleaning the grass off

@Srt8Jeep Жыл бұрын

Try not being a douche

@justinsweet2028 Жыл бұрын

It's not a how to clean the deck because we don't want to get dirty its to show you how to save a cuple hundred at ur local rip off shop