How To Replace A Gasket On Your Big Green Egg

How To Replace A Gasket On Your Big Green Egg - Ace Hardware

Рет қаралды 67,249

Күн бұрын

Watch as Ace's Grilling Expert, Chef Jason, shows you how to easily remove and replace the gasket on your Big Green Egg.
Video Chapters:
0:00 - Introduction
0:45 - Remove Dome
2:21 - Scrape Off Gasket
3:40 - Replace Gasket
5:17 - Repeat On The Dome
5:35 - Reassemble
8:18 - Closing
Print Checklist Here: tips.acehardware.com/videos/h...
Products Featured:
Big Green Egg
www.acehardware.com/big-green...

Пікірлер: 42

@stevee7774 2 жыл бұрын

Lol! Cut bottom gasket too short and tried to hide it by covering with left hand.. 😂

@bassguitarislife3419 Жыл бұрын

I recently acquired a used medium BGE & it need a new gasket. Very helpful video!

@jamespaul1835 6 ай бұрын

Nice clear video. I was just gonna do this without the video but I’m glad I watched this first.

@kg4giy 2 жыл бұрын

If, like me, you have an XL Egg, remember that top dome is HEAVY and if you are not used to hoisting it by yourself, have a spotter nearby to help re-center the dome in the ring. I got hung up on the thermometer when the dome shifted. Great tip. I like to swap out my vent gasket at th same time as the main gasket (needs a bit more felt - they sell a separate gasket kit).

@mandypresley7611 3 жыл бұрын

Great Video! It really helped me change my gasket without any problems😊

@mandypresley7611 3 жыл бұрын

Great video! Really helped me to change my gasket 😊

@stevenlivingston368 4 ай бұрын

My large is 15 years old, I still have the tabs to hold my hinge in place. Thanks for the tips

@wordsmithb Жыл бұрын

Couldn't have done it without you!!!

@RichSQ5 3 жыл бұрын

Thanks for the video. It would be nice to have this checklist in pdf. Suggestions for content- what’s the best way to clean the plate setter and how’s the best way to avoid cracking the plate setter. I’ve gone through a couple probably due to to extreme of a temperature difference when outing into a hot egg.

@m1a1abrams3 4 жыл бұрын

Chief Jason Moore here again to enlighten us.

@ChefJasonMorse 4 жыл бұрын

Ha Ha, thanks. Happy Cooking, Chef Jason

@richardbierman16 3 жыл бұрын

My last gasket replacement I put acetone in a plastic squirt bottle and soaked the old gasket before trying to scape it off. A lot more of the old gasket will scrape off clean so there's less to scrape and brush. A little more acetone later to get it squeaky clean.

@ChefJasonMorse 3 жыл бұрын

We used acetone on this change and we’re able to get all the gasket material off to ensure the new gasket sticks good. Happy Cooking. Chef Jason

@rexluger1940 3 жыл бұрын

I use a an angle grinder with a wire brush attachment, painters suit, goggles and mask. That porcelain glaze is very resilient.

@newspokes70 7 ай бұрын

Pumice stone helps if the old one is tough to get off

@ChefJasonMorse 7 ай бұрын

that will work too. Chef Jason

@d307p 4 жыл бұрын

I don’t own a BGE (I’m Kamado Joe Big Joe guy) but I watched and liked your video cause your videos are very informative.

@bas1654 3 жыл бұрын

Hi there, did you also did the dollar test? My XL was very difficult to get the alignment properly. Also the springs tend to pull the back of the lid up, i pulled to lower band a bit down on the back and its oke now.

@ChefJasonMorse 3 жыл бұрын

I didn’t do the dollar test. I know there is a tiny bit of rear adjustment on the hinge to get it dialed in.

@dannellums7154 Жыл бұрын

What about reconnecting the spripngs?

@ChefJasonMorse Жыл бұрын

HI Dan, Once I snug down the nut caps,. I will open the dome carefully and attached the springs. they are in a relaxed position when the dome is open. Thanks, Chef Jason

@jarredmahoney719 4 жыл бұрын

Can you do a peach cobbler or apple crisp on the traeger please and thank you Jason!

@AceHardware 4 жыл бұрын

Great idea Jarred! We'll add it to the Chef's list!

@ChefJasonMorse 4 жыл бұрын

Great idea. Sounds like it’s added to my list. :-). Apple crisp with sweet cream. Mmmmmm

@sms9106 3 жыл бұрын

Word of warning sometimes the existing gasket adhesive is insufficient. 3M Super 77 Spray Adhesive may be your friend.

@richardbierman16 3 жыл бұрын

Perfect time to do a high temp burn off since you're ready to replace the gasket anyway. It would be a good video, but I think you're supposed to remove the thermometer if you get it up close to 1000 deg. You're dome and fire ring whitens up almost like new. I plan to do this soon as my gasket is getting old and brittle.

@ChefJasonMorse 3 жыл бұрын

We will take a look at that. Thanks, Chef Jason

@billwaterhouse3959 3 жыл бұрын

Where did you get that table? Thanks

@ChefJasonMorse 3 жыл бұрын

Bill that is the new BGE Modular Nest. the side table is an add on, but makes for end epic pizza station. Chef Jason

@xeroblastx 2 жыл бұрын

Ace hardware carries them

@iharfor 3 ай бұрын

You said you needed a 1/4 inch gap on the lower band but you never adjusted it to that 1/4 inch gap.

@ChefJasonMorse 3 ай бұрын

HI Iharfor, apologies, it seems I did that off camera. Chef Jason

@georgeconnelly7958 3 жыл бұрын

Not necessary to remove the lid.

@DsChelI 2 жыл бұрын

I was wondering this...

@jthet2001 9 ай бұрын

Exactly. This was a lot of work for no extra gain. I'm looking at my BGE now and no way I need to remove the lid to do this

@user-ww6jm2wg6b 7 ай бұрын

I came specifically to see the springs go on and I’ll be damned

@ChefJasonMorse 7 ай бұрын

HI User, Once I snug down the nut caps,. I will open the dome carefully and attached the springs. they are in a relaxed position when the dome is open. Thanks, Chef Jason

@jthet2001 9 ай бұрын

Complicated solution to a simple problem. You don't need to remove the lid.

@ChefJasonMorse 8 ай бұрын

Thanks for watching, I find removing the lid helps me get the gasket seated properly and then also helps with alignment of the dome to the base. No overbite or underbite. But whatever works best for each person is great. Happy Cooking, Chef Jason