How to Replace Brake Pads on a 1998

How to Replace Brake Pads on a 1998 - 2002 Honda Accord

Рет қаралды 350,329

Күн бұрын

Step-by-step instructions on how to change the front brake pads on a Honda Accord. This is a simple and easy to execute process -- once you know how. Tool Dude Tony walks you through this in an easy to understand style and it's subbed!
Please share this with your friends and follow me on Twitter - #!/tooldudetony
Tool Dude Tony's Disclaimer:
Due to factors beyond the control of ToolDudeTony, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ToolDudeTony assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ToolDudeTony recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ToolDudeTony, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ToolDudeTony.

Пікірлер: 112

@jackieg1518 9 жыл бұрын

Brother..Thank you so much!!!! I watched your vid this morning before work and replaced my pads on my '99 Accord after work. I am not mechanically inclined at all, and i did both front pads in half an hour..Aloha from Hawaii my Brother and Thanks again for this video...😄

@uselogic22 8 жыл бұрын

VERY IMPORTANT BOYS AND GIRLS !!!! YOU NEED TO REMOVE THE CAP FROM THE MASTER CYLINDER (BRAKE FLUID RESERVOIR) BEFORE COMPRESSING THE PISTON IN THE CALIPER. OTHERWISE YOU COULD CAUSE A LEAK IN THE BRAKE SYSTEM BY FORCING IT. Dude you really should of mentioned this, some people out there don't have common sense...smh

@jamescc2010 8 жыл бұрын

+uselogic22 Thanks for this safety tip.

@joseachavez8002 10 жыл бұрын

This was the easiest way to replace the front brakes on my 2000 Accord

@SEBAS31077 10 жыл бұрын

damn i put the gel on the other side of the pad

@Christiantimmy 8 жыл бұрын

Best brake video I've seen for this car so far! Thank you!!!

@DiegoVansante 9 жыл бұрын

Thanks for the video and instruction. . Sure took the mystery out of doing the break job on my 1998 honda accord. Replacement went exactly as shown. Thanks again.

@SilverMoonJoe 9 жыл бұрын

Thank you kindly for your informative and instructional video. Will be doing mine this coming weekend!

@eliellison3822 10 жыл бұрын

thank you for the great video. I will be attempting my Honda Odyssey brake pad job tomorrow, the good Lord willing, and hope to have good results. Your video game me the needed gumption to try it. I bought the same brake pads you used, and will still be far cheaper than the brakes and exhaust places prices.

@bfw59 10 жыл бұрын

Wrong grease for the slide pin bolts plus grease both bolts. One more comment on old rotors check the thickness to make sure they are not too thin.

@eduardokrause1234 10 жыл бұрын

great video and made with humor! will give it a go an save myself the 800 bucks I was quoted for the 4 wheels - thanks!

@mrsberg09 10 жыл бұрын

My husband said I should put brake grease on the ends of my brake pads where they sit inside of the slide guides. This is do to the fact that they are moving parts and will help them from binding as they slide. Is this true? If so why wasn't this mentioned in your video. Thank you for this information. This was a very informative video for a girl like me to understand.

@MrWomey 10 жыл бұрын

I finally got around to watching this one... great video (don't have any brakes to fix right now, but will definitely keep this one in mind to fall back on)

@ELChavalon.3 8 жыл бұрын

Thank you for making this video so simple ;and infromative.

@jdawa6569 8 жыл бұрын

Thanks man. Just followed your advice and did it. Keep up the good works.

@Pimpscoify 10 жыл бұрын

first time doing it myself and this video help out so much. thanks tony!

@joet4806 8 жыл бұрын

Great Video. good lighting! Very clear & easy to understand.

@naturaldude64 9 жыл бұрын

Thanks for video. Easy brake job I have seen. Will do mine this time

@attpureownpk 11 жыл бұрын

Thanks for the great simple and informative video Tony!

@adrianortega7007 10 жыл бұрын

Thank you so much:). This video was detailed and helpful, I successfully changed my brakes. I subscribed too!

@snideelf 8 жыл бұрын

Thank you very much. Clearly explained and done. Great video. Well done. Hey. Crocks are very comfortable for kicking around the house. Thanks again. To remember when I look at this video again before I start: REMOVE THE CAP FROM THE MASTER CYLINDER (BRAKE FLUID RESERVOIR) BEFORE COMPRESSING THE PISTON IN THE CALIPER. OTHERWISE YOU COULD CAUSE A LEAK IN THE BRAKE SYSTEM BY FORCING IT.

@atatkfighter 8 жыл бұрын

Very clear video and you made that look easy.

@RICKYOUSSEF 9 жыл бұрын

Nice job on the video.. very straight forward and helpful...

@DerrickMovies 11 жыл бұрын

Wow, that looked so easy! Thanks for your work!

@lesliebusby4099 8 жыл бұрын

instead of C clamp to reset caliper piston use long screw driver, insert into hole on caliper & pry piston flush before removing caliper, found on fix book video BUT Tool Dude TONY's video is the easiest & BEST I'VE SEEN TO to replace pads

@doidoi3063 10 жыл бұрын

Thanks Mr. Tony, this is really helped.

@ravenlunatic7909 8 жыл бұрын

wait,so on the accord you just have to undue the bottom bolt and flip it up?? wow! i can do that,is that all??

@jonathanjones6971 7 жыл бұрын

Great video!! You make it easy to understand............Thanks

@borderline_third_nipple 10 жыл бұрын

Right on, Tool Man Tony! Super helpful vid. You're the man.

@javiaam 9 жыл бұрын

Thanks g... the video was koo and straight to the point..... It was funny too!

@cedrik9 8 жыл бұрын

I JUST CHANGED THE BRAKES ON MY 2000 ACCORD!! THANKS TO YOU SIR!!! U ROCK!!!

@jewbacca001 8 жыл бұрын

Was it the exact same process cause I need to change mine soon

@cedrik9 8 жыл бұрын

YES!! EXACT SAME!

@ramsescastillo03 10 жыл бұрын

Really helpful! :] Gracias Sr. Tony!

@PhuongNguyen-ee1qm 10 жыл бұрын

Thank you. Mr. Tony. Have a good day.

@theweriedchananelviajero4538 10 жыл бұрын

Thanks for sharing your video and good luck tony

@marleymone2 8 жыл бұрын

I just change my own brakes!!!!!! yaaayyyeee Thanks!

@LastRonin33 8 жыл бұрын

Thanks, looks a lot easier than my Navigator! A friend changed my breaks a while back and it took forever. That seems pretty simple now that i see it done. Not sure what the problem was in the past ?? Cheers

@clawgroup 7 жыл бұрын

Thanks Tool Dude. Saved me $$$$.

@thurm101 9 жыл бұрын

Thanks Tony. I been doing this for years. There is something that I saw you do that I will start doing. Using the old brake pad with the c clamp to push the caliper back in. I bought lifetime brakes at Auto Zone. I kept the old pads that I took off the car and use those as a "core" when it's time to replace the brakes on my car again. That way I can drive the car to Auto Zone and get my "lifetime replacement " and replace them when I am ready. But if you can change oil you can do this easy easy.

@MrKmanhooks1 8 жыл бұрын

I'm a huge fan of cleaning the caliper while I'm there and using a toothbrush around the piston. Calipers need loving too...

@jamescc2010 8 жыл бұрын

+Kyle Hooks Great idea to keep parts clean to protect your investment. How do you clean the caliper?

@MrKmanhooks1 8 жыл бұрын

Wire brush, elbow grease, brake cleaner, isopropyl alcohol, and then primer and paint

@kf7tkj 11 жыл бұрын

Nice little bonus at the end =)

@jordan1261 10 жыл бұрын

Awesome video man!!

@FLYBOYENTdena 8 жыл бұрын

Great video thanks man

@lopezfred27 9 жыл бұрын

thanks bro very Helpful Thumbs up

@dannymartinez4177 7 жыл бұрын

Great video! Have a question. I bought front break pads for Honda Dealer but I two break pads came with a metallic thing to put grease on back on the them but other did not. Would something happen if I put in in without metal thing and without grease.

@rustyralston8054 7 жыл бұрын

u da man tool dude

@problematic_canik 9 жыл бұрын

Thank you for this video. Saved me money let me buy you a beer.

@Big_LosF 6 жыл бұрын

😂😭😂 turbo mode. hahaha thx for the video man. great tutorial

@tooldudetony 11 жыл бұрын

Hi Donald. The top bolt holds the top of the caliper and doesn't move or pivot or anything. It is not necessary to grease it. Good idea on the wire brush work. Thanks

@GrlTakeABath 9 жыл бұрын

your awesome bro thanks.

@do0gie21 10 жыл бұрын

tool dude tony is awesome bro!!!

@landfound 8 жыл бұрын

Thank you!!!

@mattcarolina 11 жыл бұрын

Nice to the point.. 2 thumbs up

@krayzieebol802 10 жыл бұрын

Good video

@19580822 10 жыл бұрын

Thanks for the video TDT! I'm going to help my son replace his pads (he has the exact same vehicle, it's even black!), and I was wondering why you didn't mention the necessity of taking the cover off the master cylinder before compressing the piston. Is there something special about Honda brake systems that negates the need to do this? My apologies if another viewer has already mentioned this.

@tooldudetony 10 жыл бұрын

No, taking the cap off the fluid reservoir before compressing the caliper piston is something you should do. Sorry about leaving that out of the video.

@dannymartinez4177 7 жыл бұрын

Great! Thanks for video can i do the same for 98 civic?

@geechieryu8247 6 жыл бұрын

U d man tony tone..thanks

@davidwhatch 9 жыл бұрын

Thank you.

@donalddenney2954 11 жыл бұрын

Tony, should the upper caliper bolt be greased also? I find the brake pads corrode at the stationary part of the brake housing. I usually wire brush the ends where the pads slip in and grease them with the high temp brake grease.

@dannymartinez4177 7 жыл бұрын

For the multi purpose grease can i use silicone 3m paste on that bolt?

@libankatib6071 6 жыл бұрын

thanks man

@lilchooser 11 жыл бұрын

GoodJob Tony

@TheSwordofTruth 6 жыл бұрын

A little dab'll do ya. Reminds me of the brylcream ads.

@jdacdt 9 жыл бұрын

TDT....Let me know if one of your neighbors ever decide to sell their house man,I'm moving in.

@kenyonbryngel 7 жыл бұрын

Totally had one of those burlap looking starbucks tumblers, probably 5-6 years old now. neat

@Nickwithneighbors 11 жыл бұрын

More vids DUDE!!

@ashimoda9732 9 жыл бұрын

Great Video! Now can you please do a video on changing the 2 belts on a 98 Honda accord. :-)

@mandu25 10 жыл бұрын

Hello Tony, while changing the break pads of my Honda accord 2002 (LX) the mechanic broke the head of Bleed Screw which remains on Caliper Body. the break works fine, but do i need to change the Caliper Body ?

@tooldudetony 11 жыл бұрын

@etheromlet: I have done any pilots. The procedure should similar, but not identical on most vehicles with disk brakes.

@zuneid375 9 жыл бұрын

perfect video dude. hugs

@maidenwildM 10 жыл бұрын

great video Tony! what size c-clamp are you using?

@bogigasdad 10 жыл бұрын

A 6" C-clamp is what I used. Quick & easy. Don't forget to uncap the brake fluid reservoir first.

@maidenwildM 10 жыл бұрын

thank you, bogigasdad

@fanoboss 8 жыл бұрын

thanks

@bestracer500 6 жыл бұрын

No need for antisieze? Cuz 2 years down the road when we go to do this job again we can break the bolts and replace them rather than easily turn them off. Oh and it might be a good idea to pop the cap off the reservoir so that you don't bust a brake line or damage the brake system. But Mr backyard mechanic you know everything correct?

@thurm101 9 жыл бұрын

Forgot to mention. Just keep your old pads and the box in the garage. Use those as your core.

@kevinvaldez5476 10 жыл бұрын

How do I loosen my capiler nut if it is super hard like is there any tips to make it easier?

@Ricky.Ricardo 9 жыл бұрын

I'm having the same problem as well

@shanemarcotte2062 10 жыл бұрын

Same for the rear on my 1998 Odyssey?

@attpureownpk 11 жыл бұрын

parking brake should be put on? or wheels chalked off? extra jack stand in case the pump slips off or fails. when spraying brake cleaner be sure not to get it on paint! for SAFETY SAKE! A tip for the grease. sometimes the "dogs" as you call them can make a squeaking noise as well. A tip for the bolt. that mounts to the rubber gasket sometimes petroleum based lubricants can speed up the break down process of the rubber. recommended lube silicone paste. thanks! Source:EricTheCarGuy

@bfahringer3109 8 жыл бұрын

shouldn't that grease on the caliper bolt be high temp grease?

@tooldudetony 11 жыл бұрын

Your best bet is to go to your favorite auto parts store and tell them what you told me. They can look up the part number and order one for you. Get a nut too. Thanks

@xxSuPeRn0vA97 10 жыл бұрын

How long should it take for you to get a solid pedal? Like 5 minutes or less?

@tooldudetony 10 жыл бұрын

Yes, no more than 5 minutes or something else is wrong.

@etheromlet 11 жыл бұрын

well shit, thats it? wish I would of looked up how to do this along time ago.....would the procedure for most cars be the same, for example a 2006 honda pilot?

@MrOriuk79 8 жыл бұрын

same process for a 98 Accord v6?

@dannymartinez4177 7 жыл бұрын

What kind of grease caliper bolt?

@Ricky.Ricardo 9 жыл бұрын

i'm having problems removing the bolts on the bottom caliper, any help?

@jamescc2010 8 жыл бұрын

+RicYouSick Happens to us all the time. You will need to use a breaker bar, or 1" diameter 1-2 foot long steel pipe for more leverage, to loosen those rust or hard to loose bolts.

@Gravemind44 9 жыл бұрын

My caliper bolt won't budge, it's at the point where the bolts are almost circular

@NicodemusatNite 11 жыл бұрын

Hey tony I was wondering if you could make a video on how to channel water. I don't need anything coming from my downspouts. I need to channel water on the side fence and along the back fence and run off into a stream. hate that my backyard is so mushy after a rain. Sorry, I don't know how to message in youtube. Thanks.

@NSX-vq2ui 7 жыл бұрын

what about the back

@s1984khan 10 жыл бұрын

that turbo mode though

@leighatkins22 6 жыл бұрын

Tutorial bit gassy at the beginning... but pretty good... :)

@tooldudetony 11 жыл бұрын

That would be cool. However, I don't have any trailer brakes to repair. Sorry. :(

@DandiazOC 6 жыл бұрын

I think you have the wrong slider pin in the bottom

@yurmuddur420 9 жыл бұрын

You forgot where to property place the jack

@rashidchaudhry22 10 жыл бұрын

If your caliper piston has a hard time going back in, it may be very possible it is seized.

@iliketakingshowers 8 жыл бұрын

brake

@HonestOK2930 10 жыл бұрын

Why is it hard to compress the piston? I can't get it to budge.

@tooldudetony 10 жыл бұрын

I left this out of the video: You need to take the cap off the brake fluid reservoir before you compress the piston. With that off, it won't be so tough to compress. Sorry for omitting that.

@kishanpatel506 10 жыл бұрын

Tool Dude Tony i can't compress the piston???so can u tell me in details how i m gonna do that???

@keithweiser7521 10 жыл бұрын

Kishan Patel If there is dirt or corrosion on the outside of the exposed part of the piston, this can make it hard to push back in. Try cleaning the outside of the piston with brake cleaner (acetone). It takes quite a bit of force, so make sure to use a c-clamp. Something like a quick clamp might not be enough force.

@HonestOK2930 10 жыл бұрын

Turned out it was the screw kind.

@MistySandy 10 жыл бұрын

Kishan Patel If the piston won't compress, there may be corrosion (rust) in the piston causing it to jam or retract hard. This will also may cause excessive wear on the pad and heating of the rotor because the cylinder cannot retract when you take your foot off the brakes. Also, my 98 Accord is a sedan and the piston is not hollow , rather it has a cross hatch on it. (might only be on the back brake pistons due to the emergency (cable) brake. You need to turn those in. If you cannot get the piston to retract with a clamp, you should consider replacing the whole caliper with a rebuilt one for about $100 (I just replace my right rear caliper and pad holding bracket on the rear for ~ $75). It a all the pins and boots, and sliding wear parts are included as well. Take the old parts in as there is a core charge if you do not exchange the parts. Good luck. Local library is also a great place to get instructions for a brake job on a specific car. Take some Dimes to make copies. i.e. Chiltons or Mitchell repair books.