How to replace CVT drive belt on Kymco AK 550. 12K Service. USA

Рет қаралды 6,023

Kahuna_550

9 ай бұрын

Kymco
AK 550
USA
English
Cvt
Drive belt
Clutch

Пікірлер: 24

@RobertShwery 9 ай бұрын

Yeah, I noticed the addition of the 2 bolts into the threaded holes to hold the secondary pulley plates apart in the service manual. But I didn't know where those bolts came from or why they were needed, for certain, until I was at that point and I did pull the old belt off and heard/felt the plates slap together and knew there was no way to get the belt back on properly without those bolts to hold the plates apart. So I made a trip to Lowe's and bought a few stainless bolts, M5- .80 x 40 mm. I knew the could be 30 mm and still work for this, or even longer too, but 40 mm was plenty long enough. Putting the belt back on was simple with those 2 bolts holding the plates apart. I am storing those 2 bolts (actually a package of 4) with my EasyBoost variator holder tool since I will want them handy for the next time. I never removed that pulley assembly at all since there is no need to do so. I also bought a set of 13 Torx bits and 12 e-Torx sockets and the 23 mm socket needed for this job. Adding to my special tools for working on bikes. Now I have just over 12,000 miles on mine and it's going great. Best bike I've owned. -rjs987

@Kahuna_550 9 ай бұрын

Yupp, those M5- 80 are the correct ones! Me and you seem to like to work on the bike ourselves, I recognize your username from the Kymco Forums, your knowledge there has helped me to work on mine. Thanks and nice to meet you 😊

@go5582 6 ай бұрын

Its service time. Yes great video. More videos please.

@sonofodin5514 5 ай бұрын

I purchased a kymco CV3 which is basically the ak550 great video. Will help me later in time 😀

@jeandunow7794 9 ай бұрын

Well done! Now that you have 12k miles on your scoot, it'd be great if you did another video reviewing your experience with it so far, i.e. favorite accessories, likes, dislikes, etc. Many thanks!

@Kahuna_550 9 ай бұрын

I'll try to do that! Thanks 😊

@omodd 9 ай бұрын

i just bought one of these scooters. dealer service departments near me are apprehensive about working on it, thank you for the info.

@JQUICK21 3 ай бұрын

Did they say why they are not really wanting to work on them?

@omodd 3 ай бұрын

@@JQUICK21 dealer i bought it from, tech would not confirm they would work on it for several days. local dealer finally agreed to work on it for 1st service, even though they were listed on kymco’s website.

@demivrachanski9275 5 күн бұрын

You don't need this special key.... just hit it wit power toll impact

@markowade6834 6 ай бұрын

Nice informative video.

@danielnegri2993 4 ай бұрын

Well done Thank you.

@cper3587 8 ай бұрын

thanks for the tip, I get it all the tools belt , filter, roler it have 9000 mi.

@Kahuna_550 8 ай бұрын

Yeah, be good to order now and have it ready. Little expensive for shipping and parts but the tool will pay for itself the first time you is it 😎.

@milo6507 8 ай бұрын

Change the belt at 12k? I'll stick with my old Vespa, which is practically maintenance-free

@Aaron_Ron Ай бұрын

Where you buy that speacial tools?😊

@davidbrown5082 5 ай бұрын

nice video can you give us the link of the website where you got the kymco parts?

@Kahuna_550 5 ай бұрын

taiwanbigscootershop.com/collections/ak550

@Timo-Epis 6 ай бұрын

How often do you need to replace the roller weights ? I can't find it in the manuel

@Kahuna_550 6 ай бұрын

I'm not sure, when needed I assume. They were still somewhat good but I'm just going to replace them every 12k.

@jimmygrbk2b137 8 ай бұрын

I have a kymco ak 550i super touring. My drive belt got broken. Want to replace it my own. Is this a difficult job to do?

@Kahuna_550 8 ай бұрын

For the rear wheel? A little bit, lot of stuff has to he removed and doing belt tension.

@cper3587 9 ай бұрын

were to get the part

@Kahuna_550 9 ай бұрын

Taiwan big scooter shop