This video shows how to remove and replace a driver's door actuator (door lock motor) on a 2003-2007 Honda Accord.
Пікірлер: 493
@tjwtrumpet4 жыл бұрын
Thank you for this video! I just replaced the left door latch cable and your video got me through it. BUT...I found a shortcut that everyone should know. The hardest part of removing the door actuator is that ONE rod with the green clip. After trying for at least an hour to get my fat fingers up into that area with no success, I took a short break. Stood up to stretch and noticed a rubber access hole cover on the side of the door that looked to be right at the height of the green clip. I popped that puppy off and EVERYTHING is right there. And as you suggest of inserting one screw to hold the actuator in place while reconnecting everything, doing that puts that rod almost right in line with the hole & clip. Unfortunately there's no way to post pics but when you remove that cover you'll see for yourself.
@zacharygateley18273 жыл бұрын
Thanks for the tip!
@Glaze_N_Pop5 жыл бұрын
Thanks Paul! There's a few videos out there for replacing the actuator, but yours is the most detailed and thorough. You didn't miss a step. I have a working door lock now!
@gt4329b4 жыл бұрын
Thanks so much for the awesomely detailed walkthrough! Bought a new actuator off of Amazon and made this same repair on my 03 Accord this afternoon (but passenger side) - couldn't have done it without your video! 🍻
@PeterGKendall4 жыл бұрын
Whole video is darn near perfect - we changed out left and right sides using it - thanks! At the end, the final door handle cable connect with the plastic clamp - I did this just now, but forgot to seat the cable sheath's slotted plastic collar into the metal forked slot - result, I couldn't open the door from inside the car! So:: there are TWO final steps before you secure the door panel - clip the cable end to the handle AND seat the cable slotted plastic collar into the metal fork to keep the sheath in place!
@larrypisarcik2082 жыл бұрын
Very easy to understand, after walking though disassemble and installing door works great. God bless
@fadisaibi94164 жыл бұрын
Kudos! Very well made video that highlights how to handle important and tricky steps (for instance, how to not break fragile plastic piece on door handle cable). I have used it to successfully replace a failing actuator on my 2006 Honda Accord. Works like a charm now.
@jimmccullagh83074 жыл бұрын
This video is the best I found. Thank you! It was my first time pullling a door panel and replacing the actuator, your step by step instructions were very helpful. Removing the clip on the interior door handle and the window rail were the most difficult for me. Patience and watching your video on repeat really helped.
@raiderman284 жыл бұрын
jim mccullagh glad it was a help for you 👍👍👍
@thethompsons23144 жыл бұрын
Paul, your video was incredibly helpful in replacing the lock actuator in our 2006 Acura TSX. I literally had it replaced is 34 minutes start to finish thanks to your insight regarding the process and steps to do it. The process on our Acura was just like the Accord. Thanks very much, well done and very, very helpful.
@raiderman284 жыл бұрын
The Thompsons glad it worked out for you, but my name is Raul, not Paul. Hahhahaha
@thethompsons23144 жыл бұрын
Crud, sorry Raul. Guess I should have had my reading glasses on, my apologies. :-) Thanks again for your help.
@daddymac595 жыл бұрын
Hi Paul - awesome video! I used as a step by step guide to replace the actuator in my son's car. Everything worked out great. so thank you! You not only saved me a pile of cash but increased my confidence in completing other work on our family cars and keeping them out of the "stealership" as much as possible.
@raiderman282 жыл бұрын
Glad it helped you out. By the way my name is Raul not Paul. 😂
@2tommyrad6 жыл бұрын
Thanks my friend! My wife [it's her car] will be so happy to see it fixed and, for $34 I'm REALLY happy! And as far as your video-explanation, lighting, view into tight spaces... very well done! AND, you did what so many diy YT channels don't do, and that's to show the OEM part number.
@raiderman286 жыл бұрын
Tommy Rad glad it worked. If you could subscribe to my channel that would be great ( there is no charge). KZfaq wants to take down channels that don’t have 1000 subscribers or enough viewing times. I am at 762 subscribers and have to reach 1000 in 30 days or no more videos. Thank you if you can do me a solid.
@2tommyrad6 жыл бұрын
wow, you're not kidding about YT! Sub'd, liked and "bell" rang. Maybe do a one-time video with my buddy, Chris Fix. Surely there would be "bleed-over" to your channel. Lemme know what you think. And thanks again.
@MaddoxAir2 жыл бұрын
Nicely done Raul! Great instruction and demonstrations on a complex R/R. Also, getting that P/N out there is more than helpful. DIY heaven! Thanks
@FrankOtheMountain5 жыл бұрын
OMG Paul, thank you. I had a jammed lock mechanism and the door wouldn't close. Your demonstration saved me. I would've broken something.
@23werex4 жыл бұрын
I bought the actuator for 11€ (stark) and it includes this plastic piece. Works great. What a deal. Thanks for the tutorial.
@PBrown-mg4wy6 жыл бұрын
Great video! My 2007 Honda was a little different then some of the other videos of Honda's I saw (different screw placement on door panels). This was super thorough, and showing everything via video and step by step was very well done. Was able to replace my own actuator this morning. Took about 2.5 hours, but it's all up and working now. Thanks! For anyone else who does this, don't freak out if at first your keyfob doesn't work when you test before putting all back together, mine didn't, but once I plugged in the power to the window/lock/mirror panels, those buttons worked from lock and keyfob started to work.
@raiderman286 жыл бұрын
glad to hear
@raiderman286 жыл бұрын
Paul Brown if you Could subscribe to my channel that would be great KZfaq want to take it down because I don’t have enough subscribers the subscription doesn’t cost anything it’s free it just allows me to keep putting up more videos thank you
@conormckenna22296 жыл бұрын
I wouldn't have been able to replace the door latch cable/get out this piece without you - thank you. The repair probably took about an hour and a half. I was hesitant about taking off the parts as I went like the window guide/metal and rubber guide piece but it all went back into place just fine without any issue. I have a 2005 Honda Acoord V6 Sedan.
@raiderman286 жыл бұрын
Conor McKenna glad you were able to fix it.
@markhanson34155 жыл бұрын
Really helpful! One tip based on my experience, the little top rod’s snap had the little flap break when I opened it, which made it really hard to get back on, so just be careful when taking that off. Thanks!
@jackparker99975 жыл бұрын
Very detailed on the procedure, but most importantly took the time to explain what other parts could possibly break during disassembly, which was very helpful. Nothing worse than a simple repair made complicated by a plastic bit that snaps off!
@donniedeng97226 жыл бұрын
Hi Raul, Thanks for your video. My accord 2005 driver side latch stop working yesterday. Called dealer around 300 dollars. Then good to find you video. Will order the parts from Honda and try it myself first. You are really handyman.
@alonzovillegas26012 жыл бұрын
Thank you. Raul. For this excellent video.. I followed all the. Steps and. I made it.. may the Lord continue blessing you..!!!!!!
@raiderman282 жыл бұрын
Your welcome and congratulations on the repair
@mikeherzog85486 жыл бұрын
Thank you & subscribed! My son & I just replaced the passenger's side actuator in his 2004 Acura TSX with the guidance of your superb video. Your explanations & great camera angles really made a huge difference!
@raiderman286 жыл бұрын
Mike Herzog that’s awesome, glad it helped!!!
@bigdwf16 жыл бұрын
Excellent Video and great detail. Really helped me replace my door lock actuator with no issues.
@andrewthompson55185 жыл бұрын
This was a terrific video and really helped me understand how to change the actuator. I watched your video twice before starting work and the task went much faster than I expected. I found I didn’t need to take off the black cable guide - just tease out the cable, and smearing a little dishwash liquid on the metal window track really helps getting the rubber window seal back into the metal track. Many thanks.
@kylefeilmeier72614 жыл бұрын
this is the comment i am looking for, its a bitch, going to go back to the job now and finish up
@BryanMecklenburg5 жыл бұрын
Fantastic video. Once the weather gets warmer (no more 15 degrees), I will be doing this fix to my daughter's car. Thanks!
@sejincheon3 жыл бұрын
Really Great video, going to fix my son's car door tomorrow. watched your video 2 times. Feels like I can do without much trouble. Thank you very much. You are Great.
@raiderman283 жыл бұрын
Se Jin Cheon you do it!! Good luck
@ISpinUWin4 жыл бұрын
Thumbs up from another person you helped. It is nice to be able to watch someone else go through this even if it is just to verify what you think should be done or reference video for before and after steps. Thank you!!!
@raiderman284 жыл бұрын
Eric H glad to help out
@shootr045 жыл бұрын
I just bought a 2004 Accord and I’m pretty sure both front door actuators are toast. This video will be a huge help, thank you!!
@raiderman285 жыл бұрын
shootr04 your welcome
@tomvandentop38425 жыл бұрын
Excellent video and thorough. Needed help with some of the critical points of replacing the actuator on our '05 Accord. Great job and thank you for posting this one!
@raiderman285 жыл бұрын
Tom Vanden Top glad it helped
@jsutmeasimpleman4 жыл бұрын
well explained, step by step, great job. Thank you you saved me a lot of money by learning from you, how to replace my door lock. Thank you!
@2004AIH6 жыл бұрын
Thanks for taking the time to put this video together. It made replacing the actuator in our Honda very easy. Your style of filming and ability to narrate make a perfect How To Video.
@raiderman286 жыл бұрын
Mark Bennett Thank you for your kind words I really appreciate it. Subscribe to my channel, its free.
@lifesack5 жыл бұрын
Thanks so much for taking time out to share this with us!!
@ericsonmaia24215 жыл бұрын
Just perfect bro how you make the video, explanations and everything. Very detailed and patient. Thanks bro. I will do that on my car, same problem. But as it was not locking, I was using the car key and the lock stopped working too after a while, going to look for that fixing now.
@kevingentry7519 Жыл бұрын
Thank you so much for this high quality, very informative video. I was having the same problem with getting the rear rod unclipped on my 2006 Accord. I was not successful, so I decided to look for a video, and yours was the first that popped up. Answered my question very clearly. Much appreciated!
@Hymnalysis5 жыл бұрын
Thank you for posting this. It helped me make sense of some of the finer points of my latch cable replacement. Getting that assembly out and back in was the tough part!
@raiderman285 жыл бұрын
Hymnalysis yes it is. Hahhahaha you are correct.
@cayrick4 жыл бұрын
Paul, thanks for the video. I have a 2004 CRV. When I attempted to reinstall the window channel. I lined the channel bolt hole with the lower of the two holes on the door frame. Unfortunately when I tried to put on the door panel a clip was designed to fit in that lower door frame hole. To move the channel up to the higher hole it proved to be a big challenge. Mine was the frt. passenger door. This problem stopped me dead in my tracks. In your case it seems the channel was designed to fit in that lower hole.
@raiderman284 жыл бұрын
Cayrick Pan sometimes things ate not as easy as they look,& take a bit more patience. I walk away and then come back when issues arise
@Hahntech5 жыл бұрын
Awesome video. Well done. Not an easy job and on top of completing it you produced a video that showed every single detail from start to finish. You are very talented.
@raiderman285 жыл бұрын
Hahn-Tech, LLC thank you for the kind words, very appreciated
@OutOfOrderMai5 жыл бұрын
Very informative!!! I just did mine in less than an hour! Thank you!! Edit: my car is a 2006 Acura TSX and the process is exactly the same
@raiderman285 жыл бұрын
SirMai O your welcome
@kylemeyers60464 жыл бұрын
There is a plastic plug on the door jamb that you can remove to help with the inner(back) rod where it connects at the top. It made the job a bit easier. Other than that thanks for the video, it helped a lot!
@raiderman284 жыл бұрын
Kyle Meyers thank you
@Ondree6 жыл бұрын
Thank you! I've just replaced my driver's door actuator following your video tutorial :)
@raiderman286 жыл бұрын
Ondřej Svoboda subscribe to my channel its free. It helps me through youtube. Thank
@amazingtbone3 жыл бұрын
Thanks for the great video. I fixed my daughters ‘07 today. My VDO actuator from rockauto came with the new clip and looked identical to the OEM part.
@mikemike38753 жыл бұрын
Hands down the best video on door actuator on the internet, couldn"t have done it without you,
@raiderman283 жыл бұрын
mike mike thank you for the great compliment
@icookbeckyАй бұрын
I used this video for the passenger side, still a great and informational video. Thank you for sharing
@iarpak6 жыл бұрын
Thank you for your detailed video! Just used it to replace the driver's side front door actuator on my '06 Accord VP sedan. Thanks again for taking the time and effort to do this. Really appreciate it.
@raiderman286 жыл бұрын
iarpak your welcomed
@raiderman286 жыл бұрын
iarpak if you Could subscribe to my channel that would be great KZfaq want to take it down because I don’t have enough subscribers the subscription doesn’t cost anything it’s free it just allows me to keep putting up more videos thank you
@iarpak6 жыл бұрын
Raul Romo Done! :)
@raiderman286 жыл бұрын
iarpak thanks man appreciated!!
@raiderman286 жыл бұрын
iarpak 👍
@oddysee30305 жыл бұрын
Thanks man, really appreciate you taking the time to do this. Seriously helped me out!
@user-su7di2bk7u8 ай бұрын
Agreed! Nice video and very well spoken and easy/clear to follow
@samuelaiken25705 жыл бұрын
Hoping to do this on my 2005 Acura TSX soon. Hopefully it’s the same steps because no one else has videos on it for my Acura. Thank you for the detailed video🙌 will be trying soon
@raiderman285 жыл бұрын
Samuel Aiken should be similar, not exactly the same. But it will give you a good general idea how to do it
@merrelljohnson3 жыл бұрын
Thank you for such a detailed video. The process was time consuming (4 hours) bit we were cool with that. We weren’t in a rush and wanted to make sure we did not break anything.
@raiderman283 жыл бұрын
Merrell Johnson actually takes about an hour. I did two the other day and actually was able to do both in about 1 1/2 hrs. But i have done many of these
@franksilva33022 жыл бұрын
@@raiderman28 where are you located lol
@raiderman282 жыл бұрын
@@franksilva3302 i am located in San Diego ca 6219 university avenue San Diego, ca 92115
@jasonperez53433 жыл бұрын
Great video! Enjoyed the step by step breakdown and your effort to give us a visual on the inside of the door.
@raiderman283 жыл бұрын
Thank you. It was super tough, especially with my camera.
@radijana76795 жыл бұрын
Nice one Bruva done mi honda euro 07 word for word.... my driver door is on the right side of the car and did it with no problems... cheers
@PS3er24974 жыл бұрын
Amazing video my friend! Going to attempt this once I have the part you were very helpful!
@actuallynew4 жыл бұрын
Thanks for sharing your knowledge. I was able to complete this repair thanks to your video.
@TinaCalifa6 жыл бұрын
Mr. Raul, Thank You so so much for this video! Today I fix my door latch/handle of my Honda Accord 2007 thank you to YOU!! I am so happy 😃 God bless you!
@raiderman286 жыл бұрын
bertina ramos i am glad it helped and thank you for subscribing
@TinaCalifa6 жыл бұрын
Raul Romo it was very hard but I did it and your video saved me! Thank you again :)))
@raiderman286 жыл бұрын
bertina ramos it was hard recording it and doing it at the same time. Just need some patience and time to get it done
@TinaCalifa6 жыл бұрын
Raul Romo I watched it so many times and came back again today because already forgot, it took me 1 hour and 45 minutes! You recorded it for sure need a lot of patience!! I called God so many times hahaha
@paulclark46093 жыл бұрын
Thanks for posting this video. I just replaced my actuator and saved $450. Awesome!!
@raiderman283 жыл бұрын
Yup
@despiriaa6 жыл бұрын
Fantastic video and explanations. I like how you also do things properly and didn't rush. Has helped me fix my own so thankyou.
@raiderman286 жыл бұрын
De Spiria i am glad it was useful for you.
@johnathontruong9684 жыл бұрын
Amazing video I was stumped on removing the actuator from the door until you said there was a metal rod attached (hard to see part) thanks a million!
@raiderman284 жыл бұрын
Johnathon Truong glad it helped
@charlesjames79354 жыл бұрын
Nice video, I like how you explain and perform the procedure.
@jakubhryniewicz53216 жыл бұрын
I need to replace my FR handle cable, was not sure if I had to take out the whole assembly...what a pain in the ass! Thanks for the detailed video, it will make it a bit less painful.
@raiderman286 жыл бұрын
Jakub Hryniewicz glad it could help
@cranrazzic3 жыл бұрын
Without this video I would be sobbing in the garage trying to figure out all the little clips and hard to see and reach things. I don't think this is a job for the less mechanically inclined. I found the most difficult parts to be the little green clip way up inside the door, and the very fragile cable end at the door handle. It won't tolerate much tugging on it at all, which happens in the course of getting it off, and then going back together. If you break the plastic cable end at the final install, the whole process has to be redone, and more, to install a new cable. Breaking any of the little clips that may be brittle from years of baking inside the door will stall the whole repair while you scramble for parts that are not readily available. There's a lot to have to pay attention to in accomplishing this procedure. Thanks to Raul for sharing! OMG, it still took me hours!
@chriscampo45255 жыл бұрын
Your Video has helped me awesome work im waiting on my part to come in the mail and after watching this im ready for the job ......
@raiderman285 жыл бұрын
Chris Campo awesome!!!
@Jez2008UK Жыл бұрын
The best explanations I've ever watched on KZfaq and I've watched a ton. You are a natural. Thank you so much!
@raiderman28 Жыл бұрын
Thank you very much for the kind words. They mean alot. I do these videos to help people out, that are either wanting to do the work themselves or just can’t afford to pay a professional to do it.
@camargoadriano1005 жыл бұрын
Excellent video, I'm Brazil and you help a lot with my 2006 honda accord. tkx
@rs112005 жыл бұрын
Thank you so much for the through explaining on how to remove certain parts it really helped great video
@raiderman285 жыл бұрын
RS1120 i am glad it helped you.
@markonovogradec6 жыл бұрын
Great video, thank you very much, you helped me a lot! There is only one thing I would want to add. On my European model there are two more screws for door panel removal, located underneath silver plastic on the door handle.
@raiderman286 жыл бұрын
Marko Novogradec thank you. Great info. 👍
@wasif93 жыл бұрын
Great video. very datailed and thorough. Took me 2 hours but in the end all is working again. Thanks a lot for all the help.
@raiderman283 жыл бұрын
Glad it helped
@Nathan-ho8qq2 жыл бұрын
Just followed your instructions and fixed mine too. Thank you so much
@raiderman282 жыл бұрын
That’s awesome. Glad you were able to get it fixed
@hamish15346 жыл бұрын
Excellent guide, just replaced my own in 2005 Accord. Cheers.
@mdavid6265 жыл бұрын
Thank you very much, it was really helpful. I was able to change my driver door actuator without any issues.
@raiderman285 жыл бұрын
Dávid Molnár glad it helped you out
@brianelliott67136 жыл бұрын
Great video. I reckon you saved by around $200. Followed it exactly and it worked as you showed. Mind you, you were slightly quicker than me....
@Amoreno5434 жыл бұрын
Great video... followed your steps and got mine replaced.
@thessentialnetwork4 жыл бұрын
Thank you for the video my brother! It worked on my 2005 Acura TSX.
@saddop695 жыл бұрын
Legend thanks for the video! Note on my Accord euro LX (cl9) I couldn't test the lock function without having the power window harness plugged in
@raiderman285 жыл бұрын
Tori Yuksel i think that harness is the harness for both door locks and windows.
@erikandmarcie5 жыл бұрын
This saved me quite a bit of time, thank you
@mogtrader84 жыл бұрын
where u buy the part?
@Ikesviewtube4 жыл бұрын
Excellent instructions! Just replace mine on my ‘06 Acura. Thank you for the video.
@raiderman284 жыл бұрын
Isaac Avilez your welcome
@bluespring743 жыл бұрын
Thank you,sir. I was able to replace mine after watching your video although mine was Acura TSX and front passenger door, it was almost same.
@raiderman283 жыл бұрын
Tedd Ho-Jeong AN yes very similar.
@roadstar4996 жыл бұрын
Excellent video! now I see its a major pain in the ass job... i may just sell car with broken actuator..keep up the good repair videos...one of the best ones i have seen..
@raiderman286 жыл бұрын
roadstar499 Thanks
@vietao5 жыл бұрын
Thank you so much for making this video. I wouldn’t be able to fix my door without it.
@raiderman285 жыл бұрын
Viet Ao glad it helped
@gabe94643 жыл бұрын
Just did my 04 TSX and pretty much exactly the same procedures thank you my friend 👍
@raiderman283 жыл бұрын
Yes the acura and accord are pretty much the same.
@chrissam59975 жыл бұрын
I followed what you were showing and finished mine perfectly. Luckily I didn't break a little clip :) :) Great video Thank you.
@raiderman285 жыл бұрын
King Kong great job
@ugowoundo3 жыл бұрын
😂 Had to use this video to teach my mechanic how to do this, he was surprised when I told him what to do.
@HumbertoHacked3 жыл бұрын
You should've just done it yourself lmao
@gm328015 жыл бұрын
Dearest, Such a nice guy.Thanks for doing your part to help the people of the world, get some decent rubber glove to protect your hands and to keep your nails pretty, a good mechanics hands are protected b/c they are his best tools.
@raiderman285 жыл бұрын
i wear gloves when i can, but they get in the way, when dealing with small things that you have to remove or put on. hard to get a feel with gloves. i use them in some of my video when i am dealing with larger things that i dont need as much feel. thanks for caring. LOL
@miguelcotte33024 жыл бұрын
It was very helpful, thank you very much. I did the job step by step with you.
@Veng3fulsaint6 жыл бұрын
Raul, thanks for making this video! It was really helpful when I just changed out my door actuator. It had been dead for years. (Also, I hit the subscribe button too.)
@raiderman286 жыл бұрын
Glad the video helped you out, and thank you for subscribing
@mixedboi Жыл бұрын
Thank you very much my friend, you're God sent. Did the job without even scratching the paint. Sub is the least I can do.
@alb35996 жыл бұрын
Raul - great instructions. Removing the entire door lock assembly was the way to go. Definitely made getting the actuator out and in much easier. I did my 2004 TSX. Only variance with that car is the extra screw in the handle that needs to be removed, but other than that, everything else was spot on. Great future reference. Will be subscribed after I type this. It's content like yours that makes youtube valuable!
@ericphillips96082 жыл бұрын
OK, I give up. You did a great job of explaining. Thank you.
@G3ARHE4D133 жыл бұрын
Thank you for making this video, I was able to successfully fix my door that stopped locking.
@Gheorghe994 жыл бұрын
Awesome video, great step by step description of the process - thanks much - however, it looks to me like a lot of work - I think will just use the key to lock and unlock the old fashion way.
@raiderman284 жыл бұрын
Laurel99 hahhaha. If you take it to a shop maybe $50 for the part $150-200 labor
@Gheorghe994 жыл бұрын
@@raiderman28 - the Honda dealer asked for $327 - I said let me think about it - that was two years ago. You did the whole thing in 31 minutes - probably it would take me 3 hours plus and most likely break some cable and/or few clamps. As Dirty Harry said - a man must know his limitations! I appreciate your video for bringing awareness to my lack of skills!!!
@stevestock24396 жыл бұрын
Really nice video. Dealer wanted $350 for parts and labor. Saved my Sister in law a bundle here.
@raiderman286 жыл бұрын
Steve Stock i am glad it helped you out. I usually charge about $195 labor on these plus parts are about $50-$60. They are a bit time consuming. This one wasn’t that bad.
@CarlosArmijoMaripangue5 жыл бұрын
Gracias amigo, ahora puedo cambiar la chapa de mi Honda Accord 2005, lado del pasajero!!
@jaysheldon64432 жыл бұрын
Awesome video thanks. I would add that on the door jamb at the top is a black plug. That plug pulls out giving you better access to the green plastic holder that connects to the rod. Still a tight spot but with a screw driver in that hole and your hand through the other its doable.
@raiderman282 жыл бұрын
Yes you are correct. I noticed that when i was done
@danielrusu20906 жыл бұрын
you are a genius man, God bless you!
@raiderman286 жыл бұрын
Daniel Rusu glad i could help you out.
@raiderman286 жыл бұрын
Daniel Rusu if you Could subscribe to my channel that would be great KZfaq want to take it down because I don’t have enough subscribers the subscription doesn’t cost anything it’s free it just allows me to keep putting up more videos thank you
@Zerohvx15 жыл бұрын
This is the best video I've seen so far I have a 04 accord which needs both driver and passenger door lock actuators to be replaced. I already have the parts to replace the old although the only question I have is the passenger door wont open from inside or out what could I do? Thanks.
@raiderman285 жыл бұрын
Erik Burgueno you will have to probably take the front seats out through the drivers side, then try to remove the door panel ( which might get damaged in order to remove) then find a way to open the door, by pulling on the cable that’s attached to the handle. That cable has a tendency to break off right where it attaches to the pull handle ( they get brittle)
@walterllop664 жыл бұрын
Gracias Raul por el video. Este fin de semana es mi turno de hacer lo mismo en 2006 Accord
@raiderman284 жыл бұрын
WALTER LLOP 👍
@stevensanabria13262 жыл бұрын
Hey Raul. I don’t mean to be part of the chorus, but I have to say it. It’s true. This was a great video. You really did everything well and I appreciate it. There is only one problem and it’s not your fault. The door rods are mysteries to me. I think part of the problem is that I need to see pictures, and I’m not real clear on how they were attached. I think it’s some thing I would have to try and do. Anyway, this video is perfect. God bless and thank you.
@raiderman282 жыл бұрын
The kind words are always appreciated. Like the video , it helps me out. Thanks again
@stevensanabria13262 жыл бұрын
@@raiderman28 Hi Raul. Me again. What is that pink part that you busted? I’ve been looking at the schematics online and I don’t have any idea what the part number or name is. I want to order one because I don’t have a body shop next door to my house. LOL. Thx!
@raiderman282 жыл бұрын
Its called door lock rod clip. Have no idea of a part number
@stevensanabria13262 жыл бұрын
@@raiderman28 thank you!
@thebarrowfamilyaquarium55535 жыл бұрын
Thank you, this helped my through my DIY project.
@raiderman285 жыл бұрын
The Barrow Family Aquarium i am glad my video was able to assist you 👍
@daviderhahon3 жыл бұрын
4:30 and 10:30 Thanks for the details and camera angles there. Extra tip, anyone doing this job could get an endoscope to help view internal clips better.
@ruthmartinez83274 жыл бұрын
Excelente explicacion, todo funciono tal y como el video lo muestra.
@kerrydailey33744 жыл бұрын
The video was very good and it saved me several hundred dollars. But I caution you, if the car is an older model be sure to get a new cable for the inside door release. On older cars the plastic becomes extremely brittle and the head of the plastic sleeve WILL easily break as mine did. After this I needed to replace a window regulator and the second one broke (as the one in this video did). Save some time, the cable only costs about $15.
@raiderman282 жыл бұрын
You are correct on that door release cable, they do break easy, since those vehicles are older now. This vehicle didn’t have alot of miles on it, so the cable gave me no issues
@juniormartinez89496 жыл бұрын
Raul Romo.Thanks for the video.....it was very helpful.
@raiderman286 жыл бұрын
Junior Martinez glad it helped
@hectorcortes11384 жыл бұрын
Enjoy the video like the way you did the step by step very helpful
@cntrdsole6 жыл бұрын
Saved me. Thank you very much!
@gilsongallego23286 жыл бұрын
Good video. You should do a link to the parts needed on Amazon. They give you a commission on things sold thru the video. Good luck and thanks
@raiderman286 жыл бұрын
gilson gallego you ha e to be pretty big on KZfaq before you can be an associate. Then they sponsor you and you can try out products and can make money if people’s buy from the link