I used kzfaq.infoUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K this for the first time today to replace the front wheel bearing on my rwd 98 dodge dakota. This had absolutely no issue removing or reinstalling the lug nuts and it took off the axle nut without any struggle. Sounds like it's got some muscle to it. Time will tell

Let me give you some words of advise. Get some sheet lead and line those jaws with the lead. Clamping down on those gears with steel jaws will ruin some gears. The lead will cushion the gear while holding it stable.

Nice dahil sayo madamikang natutulongan mga carpenter

Open the chuck jaws. Remove the screw located in the centre. Fit a 3/8" (10mm) Allen key into the chuck and tighten with the chuck key. Smack the end of the Allen key with a hammer in an anti-clockwise direction and it will unscrew from the machine. Refitting is a reversal of this procedure. You do not have the split the drill body.

Sir thank u sa video mo natuto ako pano mg replace Ng drill chuck more bless sa channel mo sir..now I know...yes!!

Thank you very much, now I can easily replace mine🇿🇦

Great Video! This is the only way to change the chuck if your drill spins too loosely to untighten the chuck the other way. The other way is tightening the chuck on a hex wrench and hitting it with a snap. My chuck was actually stuck in the open position so I couldn't tighten it on a hex wrench....this video saved my drill! Thanks.

nice bro maraming matulongan

Thank you po Sayo sir.maaayos Kona itong sira na electric drill na SI na Ang drill shop.

Very good information, thank you bro

Very helpful boss galing napalitan ko na chuck ko nabasag kasi ang bit kala ko may naiwan pang turnilyo big help talaga

Thank you, that helps me.

lol.that was easy.glad the gear didnt break when you lock on the vice.😅

Desde colombia. Gracias por el video. Solo es que el tornillo que sujeta al mandril es rosca izqierda para que tomen nota y miren como gira el destornillador. Gracias vale.

Canal show de bóla dicas top mesmo parabéns amigo 💯👍👍🇧🇷

Thanks for the video. If the video had been available many years ago I would have replaced the chuck on my old B&D. Replacement parts were more readily available and cheaper. These days the replacement chuck costs as much as a new drill so I would just toss the worn-out B&D and buy a new one.

ကျေးဇူးတင်ပါတယ်ဆရာ.....နည်းလမ်းလေးဝေမျှပေးတာ

Thanks it is good video but it can be replaced without opening the cover..

Good nagkaroon ako ng idea thanks

Thanks for video now I can replace my drill chuck

Amigo creo que debiste colocar algo,entre las quijadas o mordazas de la prensa, algo así como unas tiras de madera, para no dañar el engrane.

Great job and good video if u move the music🙏👍🤣🇩🇰

never seen it done like this before. There is a much easier way

Very nice 👍👍

kafi bidwan ho bhaisab aap..gear ko vice me tight kardiye bina packing k... naman aapko

Very good idea thanks

You don't clamp gear on a vice Steel to steel .you can use Taflon or copper in between To avoid damage the gear. To replace chunk today is not Profitable as too many cheap Chinese drilling machine on the market

Thank you so much for sharing this video idol keep safe and stay healthy idol Godbless you always 🙏😍❣️

The 'smack with a hammer' technique probably applies to older drills. I have a drill dating from about 2015 and wanted to remove the chuck. Unbeknown to me, there is a screw, left-hand threaded accessible with an Allen key placed into the fully open chuck. Old man with 'weak' hands that I am, trying to undo this screw as though it were normal RH, snapped said screw in two. Drill and driller are both fine but replacement LH screws are not that cheap or readily obtainable!

Good idea dear

ILike 😻😻

unbelievable, unscrew the whole Drill to change the chuck; he did not need my friend

DE VALT ,10mm ഡ്രിൽ മെഷീൻ റെ ബോൾ ബെറിങ് കിട്ടുമോ നമ്പർ അറിയില്ല

Never clamp a cog wheel in a vice. If it is necessary, then use a soft wood in the vice jaws to protect the teeth. The drill does not need to be disassembled to replace the chuck. See other videos.

Exelente video

maraming salamat boss godbless

Maraming salamat sa kaalaman bro stay safe god bless.

Thanks I didn't know that

I would bet Noah was the previous owner of the vice.

Good 👍

You replace the chuck but you damage the gear.

Hvala na savjetu

First and foremost, you don't really need to pull out the gears in order to change the chuck. Looking at the damage on the collet gears, it seems that you are a rough user. This is further demonstrated by the way you clamped the gears directly to the vise. I am not surprised that you will soon be changing another chuck in a very near future.

i am learning thanks.

Very good thanks you

Thanks for showing the long way to do this

you have seen the hard way now i will tell you the easy way place drill in vise open chuck insert screw driver turn clockwise to remove the screw insert the key in chuck give it a good (WACK) counter clockwise now unscrew old chuck add new chuck install scew counter clockwise you are thru a 5 min job..

good video

Awesome instruction video 😎

For a 9 mins video he has taken 4 mins to adjust camera.

You use vise to hold the thread?. It can damage the teeth

Very nice video thank you sir very much.

nice

My B/D drill with attachments to fix I just have to put bit tighten key & give it slight blow from a hammer to remove the chuck to fit attachments, eg. saw, orbital sander etc. No need to remove any screws or open the body cover.

It looks like you cheeched the teeth on that gear by clamping it unprotected in your vice. I could see the damage when you removed it. You need to put some wood, leather, or something else between the vise jaws and your workpiece to prevent marring.

Merci pour l’astuce . J’ai un problème pour changer le mandrin je ne sais pas comment m’y prendre.

i believe you can do it without overhauling the device

Wrong method... Between the steel wise plates, Gear will get damaged

thanks bro

Usta o MANDRENI böylemi değiştiriyor aslında çok basittir

굿

👍👍

Solo tienes que meter algo en el aspa para que no ae mueva y girar el trompo del lado contrarip de comongira y ae suelta y metes el.otro listo

👍👍👍

great.

Thank you for your post. I like this vd.

👌👌👌

Bos sy butuh buat merk bor maktek ...

R u not damaging the teeth of the cog, by clamping it directly on a vic?

Thanks for your time, but I don't disassemble the drill to disassemble the chuck, I have a used key that enters and blocks the axis and then I unscrew the chuck

Sir sira po angle grinder brand makita naupod po ung carbon nasagad q po nung palitan q ng carbon brush parang sinusunog nalang nia ano po dpat gawin dito tnx..po..

Vejam meu vídeo como tirar o mandril sem desmontar a máquina

THANK YOU FOR YOUR CLEAR VIDEO

That is completely correct. When I change a tyre, I also drain the coolant first.

This video can be done in 4 mins.

Methuselah called... he wants his bench vice back.

Nghĩa là m thay cái mới, vẽ chuyện

Thanks you sir

Um das zu machen, -also das Dreibackenfutter zu wechseln- benötige ich maximal 2 Minuten! Hätte er nicht so oft beim festziehen oder lösen in die verkehrte Richtung gedreht, so hätte er schon viel Zeit gewonnen. Er wird nie ein Handwerk ausüben -soll man lieber studieren- da kann er sich anders blamieren! Der Schreiber ist gute 85 Jahre alt und wwünscht noch viel Erfolg!

👍

Hahaha siraniko😂

Vice the gear to open the chuck ??

Thanks

I have a 10 mm chuck fitted in my drill which I want to change to hold 13 mm Chuck which can be used for 13 mm bits. What I had to do for this conversion.?

HAI GOOD AFTERNOON SUPER idea SUPER WORKING SUPER Replace Another THANKS 👍👍👍👌👌👌🌹🌹🌹

Kesuen langsung copot baute didrip kendoni

TQ

Thanks🌹

Big mistake! Don’t use a vice on that gear! Now you will need to replace it!

Mas maganda cguro kong samahan mo ng instruction o magsalita ka para mas lalong maintindihan ng nanood

When do you chage a drill chuck ? Blund ?

It can be done unscrewing the machine.

Con una prueba al taladro se ganan el trabajo .

Brilhante a essa eu vou aprender 😃👍

Looks like the vice (correct spelling!) is next in line for a makeover!

More easy method without opening the drill set 5 min job Plse avoid long ways

Thank you

Sir kapariho din ba ng black&decker yang nasa video nyo

the chuck may its good but the gear may cause damage at vise may cause crack

You better be careful you don't strip that drive gear.