How To Replace Ford Fusion Cabin Air Filter

Рет қаралды 128,679

3 жыл бұрын

How to replace cabin air filter in your Ford fusion 2013 - 2021 model year. This video will give you a visual guide on how to replace or change the cabin filter in your ford fusion. This cabin filter replacement works on all ford fusions (titanium, platinum, hybrid, energi, ecoboost, and se models). The car in this video is my 2017 Ford Fusion Energi Titanium. Let me know if you have any questions as I am more than happy to help! I hope this video helps you change the cabin filter in your ford fusion!
FRAM Fresh Breeze Cabin Air Filter with Arm & Hammer Baking Soda, CF11775 for Ford Vehicles Cabin Filter Used In This Video: amzn.to/3naqAaB
The BEST Pressure Washer Set-Up:
pressure washer : amzn.to/2BNGqQT
mtm foam cannon: amzn.to/36mw0pS
mtm spray gun and wand combo: amzn.to/2qRojY7
coupler: amzn.to/2Zw2RXQ
50 foot hose (not needed): amzn.to/2zZfxMb
best snow foam: amzn.to/3eaac3n
water filter: amzn.to/2zYHmnS
1.1mm orifice: amzn.to/3bOve60
MY DETAIL SETUP! :
P&S BRAKE BUSTER: amzn.to/3aHryTP
SPRAYER: amzn.to/39IAAi6
WHEEL BRUSH KIT: amzn.to/3dVzWRE
AIR BLASTER: amzn.to/2yvtSiF
Rust Stopper: www.autogeek.net/hydes-serum-...
CarPro CQuartz Leather Coating: amzn.to/2xEOeWs
P&S Xpress Interior Cleaner: amzn.to/39xAEBh
Detail Brush: amzn.to/3bJL02H
Microfiber Towels: amzn.to/2JsxX9D
Best Foam Cannon: amzn.to/2p8d2SR
Best Pressure Washer: amzn.to/2BNGqQT
Sprayer With Swivel: amzn.to/36e2ZfG
Pressure Washer Sprayer and Wand Combo: amzn.to/2qRojY7
Foam Cannon and Sprayer Combo: amzn.to/2pWCf2E
Favorite Snow Foam: amzn.to/2WoOBMX
Favorite Paint Sealent: amzn.to/2MTV3Zg
Best Bug Release: amzn.to/31M2l5C
Best Car Soap:amzn.to/31WqpCF
Best Detail Spray: amzn.to/2qJBeLw
Best Detail Towels: amzn.to/2NppYvM
Best Wash Mit: amzn.to/31OAXUF
Wash Bucket: amzn.to/2MR3Rza
Drying Towel: amzn.to/2MTJH7N
Favorite Tire Shine: amzn.to/2MTZdAv
Glass Cleaner: amzn.to/2MTwHid
Best Leather Cleaner Combo! : amzn.to/2pavdaz
Best Clay Bar: amzn.to/3466dzS
Favorite Interior Detailer: amzn.to/2pWdeo8
Favorite Ceramic Coating: amzn.to/2BNF9sW
The Best Iron Remover: amzn.to/36cidBE
BEst Wax Liquid: amzn.to/2pTBCXv
BEst Wax Paste: amzn.to/32QXdP2
Video equipment:
Camera: amzn.to/2CSNQ5S
Mic: amzn.to/2OeoPHu
Camera Stabilizer: amzn.to/2OnippE
Monitor: amzn.to/34iyyUl
mouse: amzn.to/35rmhNr
Keyboard: amzn.to/2O4SoMS
Amazon Floor Mats LINK: amzn.to/2O8p5Jy
Car Bubble lower: amzn.to/2rgIP4M
Top Model Car Bubble: amzn.to/2qyod7Y
Car Battery Charger: amzn.to/2O5gRlf
Rhino Hitch: amzn.to/2NSUYpg
LED lights:
High beam Low beam LEDs: amzn.to/2XlHANs
Switchback LED turn signal: amzn.to/32WNyFC
LED Fogs: amzn.to/2KuAWz4
My Dash: Cam: amzn.to/34SzD52

Пікірлер: 227

@johnmal5975 3 ай бұрын

2 minute project turned into a nightmare. Thanks Ford! Great video well done!

@pickygarage 3 ай бұрын

It’s such a pain in the ass

@lmoore3rd 10 күн бұрын

Christ Ford, you sure made this easy. My previous Toyota was also behind the glove box and required no bolts or screws.

@Schwxrzritter 2 жыл бұрын

Just started working at a Ford dealership this Monday and was taught these filters today. Apparently that left screw always gets lost behind all the stuff trying to put it back in and most techs don't bother to retrieve it, the other 3 are good on their own. So if anyone loses it, just know 90% of the time ford techs do too and aren't too pressed about getting it back, so don't worry too much if any of you guys drop it and can't get it 😂

@pickygarage 2 жыл бұрын

Hahahahha thanks for this !

@srf1984 Жыл бұрын

That just happened to me😆

@carstenwilliams7733 Жыл бұрын

Yeah I just had a replace a 4th blender motor so was on that side. I have changed my filter. The blender motors are junk for ford and my ford fusion my ford's won in four years

@bertburger6024 3 жыл бұрын

Someone please fire the dude who thought of that air filter placement at Ford! This is mostly the worst I've ever seen!

@jameshoopes6467 2 жыл бұрын

And beat the person with cabin air filters on the way out.

@ralphstinson6133 2 жыл бұрын

Wait until you change the headlights...

@whoc4r3s117 2 жыл бұрын

Came here to mention the headlights. There is a reason ford isn’t making cars anymore and focusing on trucks.

@neilreid2298 2 жыл бұрын

@@ralphstinson6133 - no kidding. Entire front end clip has to come off. Absolutely ridiculous. Love my 2016 Fusion but some of the maintenance work shows the poorest engineering design of any car I've ever owned.

@ashekferdous2567 2 жыл бұрын

It's really easy compare to light change....😂

@dan4vallejo Жыл бұрын

Great video. Just shows how crazy these car designers make it to do SIMPLE maintenance!

@daviedanger1633 Жыл бұрын

Heads up for anyone stuck, there are 2 more hidden screws under the left and right side of the bottom of the glovebox. Removed those and the glovebox came right out.

@pickygarage Жыл бұрын

Thanks for the help Davie

@mandibeeharris6927 8 ай бұрын

There’s a reason that NO ONE. Literally not ONE mechanic has EVER mentioned to me that it needed to be replaced or asked when’s the last time I had it checked.

@Sleepynachos 3 жыл бұрын

Thanks for the video man. Always such a pain in the ass to replace the cabin air filter on this car lol.

@pickygarage 3 жыл бұрын

They really make it so hard these days ! Glad my video helped! Thanks for checking out the channel!

@yusuftunc3444 2 жыл бұрын

I've just changed my cabin filter by watching your video. Thank you for making this video.

@pickygarage Жыл бұрын

I’m super happy that this video helped!!!

@xMysticalIcex Жыл бұрын

Thank you! I’m not handy to put it mildly and this made it super easy. I really appreciate you!

@robertbird9830 3 жыл бұрын

"show you just how easy it is" in 74 different steps

@mrjoshua6979 3 жыл бұрын

Right I was think same shit

@claytonk.515 2 жыл бұрын

Really pretty simple as long as you can listen.

@thejeffbomb 2 жыл бұрын

He had me at his “9 and 32 mm socket.”

@marcdpadova146 2 жыл бұрын

That’s because it’s a 💩 Ford. Look at the 2003 & above Honda’s take under a minute with no tools nor removing parts.

@decarloswilliams6099 Жыл бұрын

@@marcdpadova146 Toyota's are very simple as well. I can only imagine what Ford service department charge for this procedure.

@angelfandan 2 жыл бұрын

Well done! Followed you to the letter and it was a piece of cake!

@Montrail.101 7 ай бұрын

Thank you!! Liked and saved this vid. Ppl at Valvoline was confused

@stuartbrear6537 Жыл бұрын

We have owned a 2014 Fusion since new (Feb 2014) and I replaced this filter myself every 10,000 to 15,000 miles (16,000 to 20,000 km). Most were quite dirty. Be very careful not to drop any leaf debris into the fan below the filter or you will be trying to vacuum that difficult spot out. Debris in the fan will make some strange buzzing noises, trust me. I agree with everyone here that the Ford designer tasked with making the glovebox easy to hinge down well out of the way like my Mach E does, should have been supervised by a mechanic then sent back to school to finish a course on common sense.

@3monkeys224 Жыл бұрын

Thank you so much for this! Just watched 2 others before yours and yours was the best! Changing it this week!

@pickygarage Жыл бұрын

Glad it helped! Let me know how it goes !

@davek1833 Жыл бұрын

Right to the point. Thank you. Wish a videos were as good as yours

@gnohn9366 Жыл бұрын

Got the job done. A bit of a pain but not too bad. Old filter was really plugged up. Didn’t bother to unplug the wire just propped up the glove box. Thanks so much for the instructional video.

@pickygarage Жыл бұрын

Glad it helped

@disciple1956 7 ай бұрын

This Was very Helpful in changing out the C A F in our 2019 Fusion Thank Y'all

@pickygarage 7 ай бұрын

So happy that it helped you!

@porkchop10 2 жыл бұрын

I'm trying to find my 9 and 32 mill socket... I have a 9/32 of an inch lol. Just teasing man....thanks for your efforts. Everyone bitching about how bad this looks can go ahead and pay their dealer $30 or more for labor. Looks like a 5 minute job if that when you have both hands available, and aren't recording a video.

@dustend1713 2 жыл бұрын

I lost it when he called it a 9 and 32 lmfao what a chudd. But still a helpful video in the end lol.

@joeoleary9943 10 ай бұрын

Very helpful video thank you

@Vzoom99 Жыл бұрын

This video helped so much ! Thank you brother

@pickygarage Жыл бұрын

Sure thing! I actually am going to be changing the cabin air filter again today !

@felixbgc 2 жыл бұрын

Great. Thank you, very useful.

@pickygarage 2 жыл бұрын

Im happy to hear that this video helped you changed the filter on your ford fusion!

@Fallcharles 5 ай бұрын

Thanks for your video, I just changed my cabin air filter in less than 30 minutes on my 2019 ford fusion hybrid titanium. The glove compartment only has 3 screws. 2 on the top and one on the far right. Once you remove the glove compartment, there is no connector to unplug. I spent a little time searching for the fourth screw. Filter was pretty nasty. I will change it very more often. I had to trim a little the CF11775 in order to fit perfectly.

@ebikereviews101 Жыл бұрын

Thank you. Never new my Fusion had a filter. Oops. So I just ordered one.

@pickygarage Жыл бұрын

It will help a ton with air quality

@JoseRamirez-tj5oc 3 жыл бұрын

Cool thank you

@BeccaD79 Жыл бұрын

Thank you for the video.

@pickygarage Жыл бұрын

you are more than welcome! I am so happy that it helped!

@tomshieldsmith9687 2 жыл бұрын

Watched this video, went out to the garage and completed the filter change on our 2019 SE Hybrid in 16 minutes. I'm a 67 year old man with trifocal glasses. This job isn't that bad. I did not have to remove the airbag screws, though the left side under dash glovebox screw is not the easiest thing to spot. Also note, my filter cover did NOT have any screws, the tabs were hefty enough that I think you'd have to be pretty brutal to break them, and, the lid was hinged on the bottom. Apparently, Ford made improvements along the way. Again, if you have a little bit of mechanical sense, this job is not bad at all. Thanks for the video!

@pickygarage 2 жыл бұрын

Thank you for commenting I am so glad the video was helpful to you!

@mspressure1000 3 жыл бұрын

A clip fell out for me too. I don't know where it goes. Where did you put yours? So I can see if it's the sane for me.

@williambowman7037 Жыл бұрын

I noticed a filter behind the right windshield wiper motor on my '14 Fusion SE, what is that filter? What is it called and for?

@rdbramwell 2 жыл бұрын

Thank you so much!!!

@pickygarage 2 жыл бұрын

You’re so welcome !

@coquitlam6332 2 жыл бұрын

Thanks 🙏

@enacku Жыл бұрын

I just did this in my 2019 2.0 SE and there wasn't even screw holes holding the air filter flap, just the clips and there wasn't a wire harness connected to the glove box ether because there isn't a light LOL. But was still a b1tch to access the bottom left bolt , its hidden pretty good.

@stang46l 3 ай бұрын

Do u know the type of screws that hold the clamp in?

@HOlsen-xe1xy Жыл бұрын

Thank you for your info. Now I know why people don't change it.

@pickygarage Жыл бұрын

Hahaha yes they didn’t make it easy

@OsamaBenFartin Ай бұрын

Got oil changed at the Ford dealership. They changed the oil and checked everything under the hood. I asked if they checked the cabin air filter and they said no, that would cost extra. Even the dealership don’t want to mess with these.

@pickygarage Ай бұрын

Hahahahha yeah ford didn’t make it easy

@markbreal4890 Жыл бұрын

Fantastic

@pickygarage Жыл бұрын

Thank you so much 😀

@Youtubite15 Жыл бұрын

Honestly, took me less than 10 minutes to do the job. Thanks for the upload, it looked intimidating but it was a piece of cake.

@pickygarage Жыл бұрын

I’m sure happy the video helped !

@luisflores1375 Жыл бұрын

Does this have any effect on a/c performance

@mofoco1971 2 жыл бұрын

Wix part # WP10084XP It came with very good instructions pretty much tells what you have shown us on your video . But i like your video like to see it done better then reading how to . Also it said it was for a 2013 but i have a 2019 and it's the same .It's made alot better then OEM. Note mine didn't have the 2 screws on the filter door or a wire connected to the glove box term package SEL.

@pickygarage 2 жыл бұрын

Thank you for commenting! Glad the video helped !

@alamsyyd635 2 жыл бұрын

I just changed mine in an 09 Honda and was looking to fix my moms 17 fusion. It took me under a minute to do the honda no tools needed. They make stuff so complicated nowadays

@DilanGilluly 2 жыл бұрын

It's a Ford thing. I can change the one out in my '20 Forester without any tools. You literally just push in on both sides of the glove compartment, and it separates from its carrier. Then the filter is accessible right behind it. I could probably do it in two minutes, start to finish if I hurry. But Ford is too cheap to make a glove compartment that's capable of separating into two pieces like that so they make it such a difficult process.

@a.p.980 Жыл бұрын

genius design

@pickygarage Жыл бұрын

The worst of the worst haha

@a.p.980 Жыл бұрын

@@pickygarage xD

@DorktimeBwuds 3 жыл бұрын

You skip right over the most difficult and annoying part: finding that left screw underneath. Every video on changing the cabin filter does that.

@pickygarage 3 жыл бұрын

I thought I covered that in the video .

@christopherburns9880 3 жыл бұрын

Yeah, for anyone else doing this. If you have a airbag down there, it's held on with four 8 mm screws. Yout must removed all 4 before you can get to that one 7 mm on the left side.

@melissawittman 3 жыл бұрын

What a PAIN IN THE A@@! Never have I seen a car so difficult to change the cabin air filter!

@pickygarage 3 жыл бұрын

They sure dont make it easy!

@mrmikeflo11 6 ай бұрын

What size socket did you use to remove the screws?

@nickyonstilts128 5 ай бұрын

I think he said 9/32 ml size but he meant 9/32 inch, see porkchop 1's comment above & tlover94's comment.

@istudy9 3 жыл бұрын

Holy crap what a struggle! Ford is the new german maker.

@ashekferdous2567 2 жыл бұрын

Don't watch how to change the light, please. It will take you to NASA.

@steffanieropicky3116 8 ай бұрын

Question what if my switch keeps going on when i push it off. It keeps going on i turn it off. I shut the car off went back hr later started car and was fine. Down the road a bit the air went back on i pushed it off then it comes back on Is my car possesed

@Pixiegirl1280 5 ай бұрын

Mine does the same thing and I react by turning it off but a few seconds later back on it comes. I too think my car is possessed.

@Twitledum9 2 жыл бұрын

Be careful - if you have larger debris like in this video, that when you pull the dirty filter out you don't pull the filter against the top. If you do these debris can fall into the blower below and cause a really annoying noise and if it's knarly enough it can potentially damage the blower....

@unglemergy Жыл бұрын

we slide a piece of plastic underneath as a 'catch all / fail safe' lol tho

@samuelorozco7735 Жыл бұрын

Me overly caffeinated... One instruction then pause to try on my own. A Lott of pausing later to the comment section...to late

@johncunningham997 8 ай бұрын

**sigh** I wish I would have read this comment before starting. Birds nest on top of the filter, debris all tumbled down in to the blower.

@Twitledum9 8 ай бұрын

@@johncunningham997 sorry bro 🫂

@gabepencea3909 2 жыл бұрын

Thx body!

@pickygarage 2 жыл бұрын

glad to help!

@Pixiegirl1280 5 ай бұрын

I had my ‘14 for 4 years and was taking it to the dealership I bought the car from for oil changes and tire rotations before they ever told me about the cabin filter needing to be changed. I was unaware my car had a cabin filter, always thought that’s what the air filter under the hood was for 🤷🏼‍♀️. Pretty sure the cabin filter needs to be changed again because it hasn’t been changed since 2018. The dealership doing a rush job to put the glove box back in could be the reason the door to said glove box isn’t flushed closed anymore.

@996TwinTurbo911 2 жыл бұрын

What’s a 9/32 mm?

@pcnetworx1 3 жыл бұрын

I just performed this on my 2019 Fusion hybrid. The cabin air filter change procedure is not as well designed as other cars where you just move a rod and the glove box drops down extra far, HOWEVER it's also not as much of a horror story as some commenters make this procedure sound. I watched this video once through uninterrupted, then I did this project right after. I took my time unfastening everything and it was fine. And by took my time... I figured this procedure out in less than 15 minutes. Note though, the final clips in this procedure holding the door over the filter tray itself are super flimsy. I did break the right one off easily while doing this process. And after seeing how easily that right clip broke off, I understand why someone made a decision to also have screws to hold the filter door shut in case you break off the clips as I did. That's over engineered because those last plastic clips are under engineered... Interesting note if you have the 2019 SE hybrid model: in my vehicle there was no wiring harness connecting my glove box to the car. When the glove box dropped, this was helpful because the box just comes out without snagging on any cable.

@DilanGilluly 2 жыл бұрын

I mean it's really not that hard to change the battery on an iPhone, you just have to use heat and pry the screen off. May seem unrelated, but we shouldn't be making excuses or justifying companies making things less repairable.

@pcnetworx1 2 жыл бұрын

@@DilanGilluly It's a bad design for sure when many, many other cars have toolless designs for the cabin air filter. I can't change the design of the car, just filled in notes of my casual repair experience. Unrelated - but as it was broached - as a repair skill level comparison - Iphone screens are way, way worse than this job.

@trip31 Жыл бұрын

Can you please check the Amazon link? It says page not found

@pickygarage Жыл бұрын

amzn.to/3naqAaB this one will fit

@UnknownMe321 2 жыл бұрын

I need to replace mine 😬

@pickygarage 2 жыл бұрын

This is the video to do it!

@frankmontez6853 9 ай бұрын

Well yesterday the no air was coming from the vents and today it's perfectly normal blowing like new . my professional mechanic friens said it's not the filter . it's the relay or blower motor

@Twitledum9 2 жыл бұрын

what size are the bolts?

@Twitledum9 2 жыл бұрын

9/32 think he mentions it. Woops

@dacvidz 2 жыл бұрын

I think they are actually 7mm … cars are all metric

@DilanGilluly 2 жыл бұрын

Meanwhile, I can change the one in my Forester in 10 minutes or less, without any tools other than my bare hands. This is ridiculous Ford. Do better. (reason why I'm watching this is bc I may have to change it soon in my parent's Fusion)

@christianvorndran2202 Жыл бұрын

He said "side piece". I laughed.

@pickygarage Жыл бұрын

Hahahahah I love it

@3monkeys224 Жыл бұрын

Changed mine! Took 15 minutes. I did however break one clip getting it out and it went flying and then when I went to put the cover on the other side broke. There weren’t 2 screws in mine but looks like there should have been. I’ve had the car since new so it’s never been changed. It was gross

@pickygarage Жыл бұрын

I bet it was! Mine was pretty bad as well!

@calvinhenderson4200 2 жыл бұрын

I thought I was at Lego Land. Thanks

@fw1057 2 жыл бұрын

That's why my Ford dealer never try to sell me cabin filter change service

@therezman1513 2 жыл бұрын

Lmao 😂 fr.

@charlieytpw Ай бұрын

The fan roars , growls now. I noticed the new filter you had has two or three cardboard

@pickygarage Ай бұрын

Something might have fallen down into the fan when you changed it

@TheMetalmachine467 3 жыл бұрын

What if a nut shell falls down into the fan 🤔

@pickygarage 3 жыл бұрын

That would have been a problem for sure!

@michaell4632 2 жыл бұрын

Did you know that the link to Amazon store is the wrong filter. Not the CF1175 !

@pickygarage 2 жыл бұрын

Thanks for the heads up the links been changed

@tonyclams1955 3 жыл бұрын

Very good video... Little bit too much for me....... I will live a little longer with the dirty filter....

@pickygarage 3 жыл бұрын

It’s really not too bad !

@anotherone3957 Жыл бұрын

My filter has the letters upside down and the arrow pointing the other direction. Confused

@pickygarage Жыл бұрын

If you look closely at my video you should be able to recognize the correct way the filter should look going in. Let me know .

@stuartbrear6537 Жыл бұрын

The arrow should point down. That is the correct airflow direction.

@tlover94 Жыл бұрын

It's not A 932 mill it's A 9/32 inch socket Other than that good job

@movingapollo1927 Жыл бұрын

I broke one of the tabs on the filter housing 😂

@pickygarage Жыл бұрын

I have heard this happening a lot to people.

@Will-us2uv Жыл бұрын

That’s a mission to change the air filter 😅

@pickygarage Жыл бұрын

Sure is !

@ralphstinson6133 2 жыл бұрын

7mm is the socket needed it you don't have the 9/32 socket.

@Odbayar007 7 күн бұрын

Why Ford designers thought they will make the simplest task to be this much complicated? Toyota cabin filters are replaced basically within 20 seconds and no need any tools

@denawilliams9741 2 жыл бұрын

So apparently this must be the reason why my air conditioner is fogging up my windshield window because of this filter like this filter need to be changed The air is Flowing correctly Looks pretty hard to me I hope I could find someone to do it instead of taking it to the dealership wish me luck

@pickygarage Жыл бұрын

You can do it!

@karlitosway6139 4 ай бұрын

Holy smokes, I found a mouse had cut a hole through the filter and tons of debris went down the hole. Lets hope for the best.

@pickygarage 4 ай бұрын

This is the best story yet hahah crazy what you’ll find in there

@sebastianalaimo3925 2 жыл бұрын

So you pretty much have to take apart your whole glovebox just to put a new filter in lol.

@jdtravels5140 8 ай бұрын

Unnecessarily difficult. What was Ford thinking?

@pickygarage 8 ай бұрын

I couldn’t agree more !

@caliboyrob 2 жыл бұрын

ok im not doing all that to change one thing. As soon as i hear a bit of rattle from driving after changing it im going to be pissed

@pickygarage 2 жыл бұрын

Hahahah I don’t blame you

@joeb4405 3 жыл бұрын

Why did Ford make that so difficult to change?

@pickygarage 3 жыл бұрын

I really do not know! But I agree it could be easier !

@DorktimeBwuds 3 жыл бұрын

So you will pay $150 to have one of their mechanics do it for you

@pickygarage 3 жыл бұрын

@@DorktimeBwuds hahah that is so true !

@sudeshakadaniel 3 жыл бұрын

It's so easy on the Toyota rav4 no need to do.all that Ford makes it more hard

@pickygarage 3 жыл бұрын

Yeah I agree I feel like other makers make it so much easier to do !

@YourBestFriendforToday 3 жыл бұрын

Same with Honda. Just open it, hit the tabs to drop the box, two more tabs to remove the cover and all done. Am guessing Ford will change it up in their future models.

@rickyrozay5054 3 жыл бұрын

“More hard” 😂😂

@user-ge1zh3we6j 3 жыл бұрын

Yes and why does it have to be so many steps just to change a cabin filter. Changing it took me as long as getting out an air blower on the same car. Screws on the bottom especially the one on drivers side were not easy to get to.

@toddhering7804 9 ай бұрын

OK watched to video on this. On said 7mm bolts this guy said 9/32 mil. Has anyone ever heard of 9/32 mm? Second he said screws. They are bolts. A screw driver takes out screws a socket takes out bolts.

@thegovernment0usa 10 ай бұрын

Nobody puts "6 cylinder" or "4 cylinder" in their titles when they make videos about the Fusion. I have to watch it for multiple minutes before it becomes clear which one it is. This one doesn't work for mine.

@mofoco1971 3 жыл бұрын

Fram worst filters of any kind on the market. Wix is the best PF tested.

@pickygarage 3 жыл бұрын

I will have to give those a try thanks for the suggestion!

@PtrOBrn 3 жыл бұрын

WTF... my Saturn was open the glove box. Pull the sides in to get the glove box out of its track and drop it open. Insert filter and close the glove box. DONE

@pickygarage 3 жыл бұрын

Yeah it wasn’t the easiest thing in the world

@ibkruzen 2 жыл бұрын

and how many 2021 Saturns are being sold today?

@PtrOBrn 2 жыл бұрын

@@ibkruzen about as many 2021 Ford Fusions... so your point is what exactly?

@ibkruzen 2 жыл бұрын

@@PtrOBrn chill, Ford is still a brand and Saturn is GONE!!! It’s a DYI video

@bonedatt 2 жыл бұрын

What's DYI 😕

@TsRide83 2 жыл бұрын

9/32 is not mil it sea other wise would have been just 9mm

@pickygarage 2 жыл бұрын

Thanks for the assist !

@debramonzel7357 9 ай бұрын

R U kidding ME!!!!

@pickygarage 9 ай бұрын

It’s such a pain in the butt ! I just changed it again !

@okwui04 2 жыл бұрын

1:45 "9/32 mm" ...lol

@pickygarage 2 жыл бұрын

Yeah messed that one up lol

@harrydemkee3580 11 ай бұрын

No shade at the creator of this tutorial but Ford design that to be hard to replaceable simple filter. They could of just as easily added an under dash slot to pop out the old filter. Having to remove the glove box is ridiculous

@dustinmantei76 3 жыл бұрын

What in the eff is 9 and 32 mil? You mean 9/32nds? Someone take this dude’s man card

@pickygarage 3 жыл бұрын

Thank you for the correction. I always messed those things up! Thanks for commenting hope you have a great day.

@logan143 3 жыл бұрын

Omg I hate this model of fusion! Everything is over complicated!

@DT95978 3 ай бұрын

Jesus! Why didn’t they just put it in a ziplock bag inside the fuel tank?

@ducaking 2 жыл бұрын

Would have been too hard for Ford tu just cut a hole in the glove box....

@pickygarage 2 жыл бұрын

Right !

@CountryRock2k1 Ай бұрын

9/32 inch, not 9 and 32 mil.

@FranciscoMartinez-mu1ng 7 күн бұрын

I broke all my prongs doing this

@davewood4780 2 жыл бұрын

It’s 8 mm not 9/32nds

@pickygarage 2 жыл бұрын

I messed it all up lol Thanks for the assistance.

@themoo908 Жыл бұрын

Nine thirty seconds…. 9/32

@pickygarage Жыл бұрын

messed that one up big time haha thank you for the correction.

@dilloncassell 3 жыл бұрын

I respect the diy for sure but my dealer replaces them for $35....

@justinskaggs744 3 жыл бұрын

That's a nice dinner date

@DilanGilluly 2 жыл бұрын

You can buy the filter most places for a little more than $10. That's a savings of $20 or more. It's the difference of a half tank of gas here, at least for the moment.

@bonedatt 2 жыл бұрын

Most people don't make $35 an hour, so yea, that's a lot to pay for a 10 minute job.

@careycarson7629 3 жыл бұрын

Yup. My next car will certainly be made by Toyota.

@pickygarage 3 жыл бұрын

Hahaha they do make great reliable cars

@spacebound1969 3 жыл бұрын

Good for you. In the meantime, I'll be driving a car with a powerful engine, modern features, and a platform less then a decade old. Boohoo, I have to spend 10 minutes taking out an air filter for the Fusion...