How to change and remove front left wheel drive and drive shaft LEFT side Toyota Corolla years 1995 to 2012. Front drive axle.CV axle. Driveshaft. Look also RIGHT side. Here is link: • How to replace drivesh... x9
Пікірлер: 257
@geraldsaliva55598 жыл бұрын
The fact you were willing to go under a car held up by only a jack and a rock on a dirt road makes this video deserve a million likes. You my friend are a daredevil and I respect it.
@PeterFinnTheCarDoctor8 жыл бұрын
+Gerald dasilva Thank You for feedback. :-)
@drksilot6 жыл бұрын
There is not just a rock, there is also a big piece of log under it, redundant safety, jackstands in that dirt would have just sank. If anything, he is a much safer mechanic than Americans here doing oil changes with bottle jacks. A+. This vid gave me lots of pointers.
@neilward59055 жыл бұрын
I have been wrestling with half of the trans axle being stuck in the transmission for near on a a full day now, tried clamps / pullers / j bars etc etc.... this video was my last hope, and the good old Hammer & over sized flat head masonry ? drill bit from behind has finally done the job!!!!! after hours of tapping away and finding the optimum angle Peter Fin....... thanks a million man. all the way from Melbourne, Australia... where we would consider your fine self a "....Bloody Legend ! " 10/10 , excellent !!!
@PeterFinnTheCarDoctor5 жыл бұрын
Hi and Thanks for comment. :-) Best Regards Peter
@paulnunya34297 жыл бұрын
Not everyone has all the stuff to do work on their cars, I have used stuff that I had no choice to use and got the job done and saved $100 if not $1000's of dollars by avoiding a trip to the shop. The main things are safety and not breaking other stuff while fixing your car. He did both and got the car fixed. I think him taking the time to explain the procedure deserves respect. Thanks for making the video. 😎👍
@PeterFinnTheCarDoctor7 жыл бұрын
Thank You and good comments. :-)
@fritzschneider327610 жыл бұрын
Thank you for making a video showing how average people work on cars without proper equipment!
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks. And my idea is to do videos for beginners.
@Jk-oz5qn Жыл бұрын
No way those ball joint bolts on the control arms and the hub nut will ever come out this easy, at least not in the damp and wet shitty uk where every car part turns to rust
@nickduque511nd7 жыл бұрын
I have searched all of you tube and not one video showed me to take out the axle until I came across ur video and bam!!! very well demonstrated and I will subscribe thank u so much for this video
@PeterFinnTheCarDoctor7 жыл бұрын
Hello, You are welcome. :-)
@RevivalFireChurch5 жыл бұрын
Good job, Peter! Thank you for taking the time to show every little detail on doing this. Thanks for all the great work...God bless you!
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks my Friend. :-)
@BRaff-hl4ip4 ай бұрын
Peter Finn, thank you for helping me keep my 2004 Toyota on the road. You're a mighty man.
@PeterFinnTheCarDoctor4 ай бұрын
Thanks. I'm like a poor traveler on the road. 👍😀
@crissy75036 жыл бұрын
This remained me working on cars back in Mexico Every little job was a big challenge, basically doing a job without tools Well done Sr, good video
@PeterFinnTheCarDoctor6 жыл бұрын
Hi and Many Thanks for feedback. :-) Regards Peter
@RobWithTheHat10 жыл бұрын
Great video mate, I love the Borat accent to, great work for helping the world !!! 10/10
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks!
@FngBaker9 жыл бұрын
that's some nice improvise skills you have Love to see ppl doing stuff without professional tools
@PeterFinnTheCarDoctor9 жыл бұрын
Kai to Mak Thank You for comment.
@masthahn6368 Жыл бұрын
You did a pretty good job for working outside without any professional lifting equipment! 👌
@PeterFinnTheCarDoctor Жыл бұрын
I appreciate that!
@ryszardjacekrusniak79933 жыл бұрын
The best video on the subject... my drive shaft popped out by the second stroke of hammer against the chisel. Thank you very much for sharing.
@PeterFinnTheCarDoctor3 жыл бұрын
Glad it helped
@anssivahakuopus206810 жыл бұрын
Is easier open the axle head lock nut when wheel is on. Then no need brake pedal pressing systems...
@PeterFinnTheCarDoctor10 жыл бұрын
Great and Thank You for info.
@olenaerhardt77253 жыл бұрын
Also just Impact Wrench, it opens easy without any accommodations.
@konnichiwa79258 жыл бұрын
Man I love how detailed these videos are.
@PeterFinnTheCarDoctor8 жыл бұрын
Thanks for Your comment, :-)
@curryhousechicken5 жыл бұрын
You make the best repair videos as you show all the difficult parts. Hats off to you sir. Thank you.
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks Sir. 👍
@mikebaiker6 жыл бұрын
THANK YOU!!!!!! i have my air tools and stuff, but never changed one of these.Your video helped me alot. I kept thinking " if this guy can do it on the side of the road with hand tools and lumber, i have no excuse why i cant do it with alll the right tools. Again, thank you. ***** and thanks to the commenters for the heads up on breaking the 30mm bolt first. i would have made the same mistake. i know its a simple thing, but when you are trying for the first time, you get the blinders on thinking of the other stuff.
@PeterFinnTheCarDoctor6 жыл бұрын
Thank You for comment. :-)
@sallor225810 жыл бұрын
Excellent video. I am going to replace one on a 1991 Corolla, and will try to do the seal in the transmission at the same time. Your detailed video will help.
@PeterFinnTheCarDoctor10 жыл бұрын
Hi, Good luck to your work. Toyota's parts could be similar.
@sarahvallido13299 жыл бұрын
hey man that was an awesome video. your patience is outstanding. your step by step explanation from start to finish was excellent. you should me how what to expect on my toyota corolla project. from the perspective that i just watched, i wish we were best friends and you can help me with my toyota corolla. good luck to you. wish you the very best. this world needs more good people like you that help others. thank you very much. MACY
@PeterFinnTheCarDoctor9 жыл бұрын
Sarah Vallido Thanks. It was great feedback.
@ypcozzy Жыл бұрын
Great video and thanks for showing us simple tips 🙏
@PeterFinnTheCarDoctor Жыл бұрын
Glad it was helpful!
@chrisherke72610 жыл бұрын
Its not pretty, but its exactly how I have to work on my 98 Corolla. I even use the log to jack stand my car lol. I like the fact that you show that its not necessary to pull the brake assembly apart.
@PeterFinnTheCarDoctor10 жыл бұрын
Yes and You are welcome.
@j-somebody638411 жыл бұрын
Thank you for your video, how to CHANGE A DRIVE AXLE, it was VERY GOOD, STEP by STEP, you made it look really easy, now I know how to change my drive axle, thanks.
@sergejstark4669 жыл бұрын
I also would like to thank you for your gratefull videos. It is really helpfull for me!
@PeterFinnTheCarDoctor9 жыл бұрын
sergej stark Thank You for feedback.
@mcfcmanc3 жыл бұрын
Is there a video for refilling gearbox oil lost ? Great video this thanks
@mcfcmanc3 жыл бұрын
Edit: found one …. Changed oil now after changing drive shaft … old oil was really thin
@PeterFinnTheCarDoctor4 ай бұрын
Thanks for sharing 👍
@worldpeace329 жыл бұрын
Nice video , I have a different car, and been thinking to do it myself but maybe I'll let the mechanic do this for me, nice of you to respond to every comment here
@PeterFinnTheCarDoctor9 жыл бұрын
worldpeace32 Hello. If you have a Toyota car, the replace wil be easy. But if you have another car brand, it could be more difficult.
@worldpeace329 жыл бұрын
Peter Finn Yes it is another different model , i think i can do the repair myself but a lack some important tools like the spring compression and it costs more money to buy than to replace the shaft by mechanics , thanks for replying
@cutneditvideos10 жыл бұрын
The best video ever thanks
@sigfridbernal4809 жыл бұрын
Hello, thanks for your vídeo. I suggest to put a big screwdriver through the caliper to hold the disco. That has worked fine for me, and son need to
@archhangell10 жыл бұрын
good work! the best part is that if I do it your way I dont need to go for Car Alignment.
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks for comment.
@cj7andotherjeeps9407 жыл бұрын
Nice video. This job can be a pain in the ass. I've done this job before but forgot the trick I used yo get the out. I couldn't get a pry bar or screwdriver between the axle and the drive axle because the sub frame didn't give me enough clearance. I used a chisel eith a hammer on the drive axle and it came right out.
@PeterFinnTheCarDoctor7 жыл бұрын
Thank You for feedback. :-)
@1mic1stage1life10 жыл бұрын
brother you are the man. thank you very much. this video was very helpful. i would have thought it was 20x's harder to change this cv axle out. un fortunitly the 2007 im working on is slightly different because of the pressed on bearing assembly but the just of the video is perfect. to the poiunt and very detailed. thank oyu for takeing the time to explain very thing out as clearly as possible as well. as i m an american you commuicated very well to us how truly easy it is to do this task with minial bull crap unlike other videos ive watched. i my friend thank you very much for helping my and my friend save alot of time and struggles and money doing it ourselves.. A+ al the way...
@techkenX10 жыл бұрын
Nice but you could of just ask me bro I have changed out many
@1mic1stage1life10 жыл бұрын
dam foreals shit i would have if i had known. ive never seen you work on your own stuff before...you know me bro im not scared to do it... but im use to rear wheel drive cars with v8's not frt wheel drives and 4 cylinders... lol good shit tho.
@techkenX10 жыл бұрын
Lol yeah I used to work on 4banner all the time.
@1mic1stage1life10 жыл бұрын
ya im working on bobs toyota so far ive done the front calipers and pads, rear rotors and shoes, and this monday im doing tranny drain and refill along with the cv axles on passanger side and drivers side... that is the only thing i cant find is how todo the passanger side. from what i gather from others is it is different not completely but slightly. so im still looking for the video with that in it. but this guy has alot of good how to's... and i plan on making mine since i finally found my camera again...
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks Sir, Your feedback was excellent !
@aguilarkatie10 жыл бұрын
I NEED TO CUT DOWN MY TREE TO HOLD MY CAR. OK VID
@PeterFinnTheCarDoctor10 жыл бұрын
aguilarkatie Thank You.
@tomjones15779 жыл бұрын
thankyou very much for your video not so hard after all, cheers been a real help!
@PeterFinnTheCarDoctor9 жыл бұрын
tom jones Thanks for comment.
@retrobro66678 жыл бұрын
thank you Peter on changed Axel by myself you are a good person
@PeterFinnTheCarDoctor8 жыл бұрын
+Adrian Vallejo Hello and many thanks! :-)
@GeorgiGeorgiev-ne9ps4 жыл бұрын
Put a scredriver in the ventilated rotor. The wooden log on the pedal is far harder to achieve
@Barabonga9 жыл бұрын
Hey, Peter Great video! I plan to replace mine in couple of weeks by your video instructions. I have just one question:do we need to lift both front sides of the car, or just the side where we are replacing the axle?
@PeterFinnTheCarDoctor9 жыл бұрын
Павел Русаков One side is enough.
@murderWhornets7 жыл бұрын
I've got the repair manual for the Corolla, and alternative to the wood block for the breaks and having it in gear you can put a pry bar in-between 2 of the threads for the lugnuts and lock that against the floor, although I would imagine that would be easier on the 5 lug cars like my 04 Corolla.
@PeterFinnTheCarDoctor7 жыл бұрын
Hi, Thanks for Your comment. :-)
@resultsds9 жыл бұрын
Thanks for this great video, I'm planning to change mine tomorrow. I like the way you explain every step of the way. God bless you.
@PeterFinnTheCarDoctor9 жыл бұрын
Fredis Joya Thank You for your comment.
@marceberhardt662510 жыл бұрын
Thank you very mutch . I have to change it on my toyota corolla (modell 92-97) 97 touring . It helps me a lot i guess . Great video .
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks.
@melsailsnorth17 жыл бұрын
You make awesome videos! Really enjoyed this as I prepare to do the same on my mom's car!! You should be a teacher!!
@PeterFinnTheCarDoctor7 жыл бұрын
Hello and Thanks. I have been sometimes teacher too.
@robertholsopple94515 жыл бұрын
Would doing it this way require a front end alignment when finished?
@PeterFinnTheCarDoctor5 жыл бұрын
Yes
@ryanbowman87082 жыл бұрын
you do a good job explaining, but i’d invest in some real jack stands if i were you.
@PeterFinnTheCarDoctor2 жыл бұрын
Thanks 👍
@OP-ik7qb5 жыл бұрын
My respects for this video, really tough scenario to work! Thank you for sharing
@troys52865 жыл бұрын
Great videos and really good at replying to people.
@PeterFinnTheCarDoctor5 жыл бұрын
Thank You. :-)
@txchcych04 ай бұрын
Did you refill any transmission oil? I have to do this repair myself and wonder do I need to fill more
@PeterFinnTheCarDoctor4 ай бұрын
Yes Rifill
@axenz19 жыл бұрын
Thanks for the nice tips. BTW I cannot separate my Honda outer Driveshaft , I've hammer many times and it Jammed. I've use my "95MM Car CV Joint Drive Shaft Assembly Installaiton Removal puller Tool " and pipe trick still cannot separate it. Let me know you tips. Thanks again
@PeterFinnTheCarDoctor9 жыл бұрын
axenz axtiz Hello. I have made new video on drive shaft dis assembly, please look it when it is ready. So, I am planning to some video also on Honda Civic.
@axenz19 жыл бұрын
Thankyou :)
@1981blazn8 жыл бұрын
Rocks and Tree Trunk ! How about mentioning that it would be great if one also had a Jack Stand and maybe a New Auto Parts Store bought Axle because the one you are installing is clearly a junkyard Axle.
@PeterFinnTheCarDoctor8 жыл бұрын
+Robert Redford Your idea is good. Thanks for your feedback. :-)
@olenaerhardt77253 жыл бұрын
Great film, I've learned a lot.
@PeterFinnTheCarDoctor3 жыл бұрын
Glad to hear it!
@fabioferrazandradesilva96856 жыл бұрын
Show Peter, você tem os melhores conteúdos sobre o Corolla... parabéns!
@PeterFinnTheCarDoctor6 жыл бұрын
Thanks. :-)
@midnitebo5 жыл бұрын
You don't have to mess around putting wood blocks on your brakes and all that to keep the wheel from spinning. Just put a bar in between the lug studs and touching the ground to keep it from spinning. Or put the wheel back on and lower the car down just until you break the axle nut loose.
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks for comment. 👍
@samuelsippola70253 жыл бұрын
Mitä öljyä kannattaisi tuonne laittaa jos samalla öljyt vaihtaa? Which oil should i use?
@mirabilo10 жыл бұрын
you could place a long pry bar between the wheel studs and the ground to stop the hub from turning.
@PeterFinnTheCarDoctor10 жыл бұрын
Hi, Thanks for comment.
@oscarperez8410 жыл бұрын
The easiest way to loosen the axle nut is to insert a flat screw driver on the outer edge of the rotor. You have enough room to insert one and put it against the brake caliper bracket, it will not turn!
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks for this hint too.
@martinlefebvre50055 жыл бұрын
Hi Peter i have one question my 2003 toyota Corolla is it the same socket to open the axel nut a 30 mm are i need a bigger one thx for the info continue the good work my friend
@masthahn6368 Жыл бұрын
Can you tell me newton for three screws at the beginning? The main screw of axle is 200+ you said? I will do 210, is that enough?
@PeterFinnTheCarDoctor Жыл бұрын
Thank you for your message. I have read your message. 😀👍
@MechArm19 жыл бұрын
Thank you very much for this video! . .. followed step by step with you and I changed out the axle. ... . Will this same basic process work on the passenger side as well?
@PeterFinnTheCarDoctor9 жыл бұрын
MechArm1 Yes. Same idea.
@vikashkadoo971610 жыл бұрын
Do we need to refill the gear box oil after the replacement? I had my axle replace and there was a white liquid grease that was dripping. I ask the mechanic if that grease needed to be refill he said that was not necessary. Just wanted to confirm.
@PeterFinnTheCarDoctor10 жыл бұрын
You are right. Always we need to refill gearbox after driveshaft replace. Same amount new oil in, what drained out.
@baaghiisu5 жыл бұрын
The god bless him who has a good soul.
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks Sir. 🙂
@divineavengers9 жыл бұрын
Hi Peter I am going to do this on my 1994 Toyota Celica tomorrow so when I remove the axle the fluid that will leak out is transmission fluid since it is an automatic? So I just refill by adding Dextron III like I would when topping of transmission fluid?
@PeterFinnTheCarDoctor9 жыл бұрын
goldiegoo Yes, You are right. Same amount new Dexron III oil ito nside, what went outside. Please insert canister below the car.
@PeterFinnTheCarDoctor9 жыл бұрын
goldiegoo Yes, You are right. Same amount new Dexron III oil to inside, what went outside. Please insert canister below the car.
@retrobro66678 жыл бұрын
I changed Axel by myself thank you
@PeterFinnTheCarDoctor8 жыл бұрын
+Adrian Vallejo Hello and many thanks! :-)
@obiwan9225 жыл бұрын
Just wondering....You cant adjust camber and caster stetting in this car, can you?
@mdrouin1002 жыл бұрын
Hi Peter, Thanks for this video.. One trick: to block the axle you could use a strong screw driver placed in between one of the slots of the brake disc and lock it against the brake block. What do you think? Terveisia from Lpr, EK
@PeterFinnTheCarDoctor2 жыл бұрын
Good idea
@kozytoes106 жыл бұрын
Thank you sir for your excellent video
@PeterFinnTheCarDoctor6 жыл бұрын
Hi and Many Thanks for feedback. :-) Regards Peter
@reytriton8 жыл бұрын
thank you very much, very useful explanation
@PeterFinnTheCarDoctor8 жыл бұрын
+Reymar M Hi and Thanks for your feedback. :-)
@diyoregonnowtexas92023 жыл бұрын
I just did this on a 97 Toyota Tercel, but now the driver side wheel is locked up solid. wont move. Do you have any idea why this is happening?
@PeterFinnTheCarDoctor3 жыл бұрын
Use more Force and hit hard. It clicks finally. Good work, Thanks ! 👍😀
@mushukitafileso437110 жыл бұрын
is it the same process with the toyota ipsum 2000 and what are the estimated costs of the new and second hand drive shaft
@PeterFinnTheCarDoctor10 жыл бұрын
Hi, used shaft costs about 100US$ and new one about 400US$.
@raimondassemeta91053 жыл бұрын
thanks for video
@PeterFinnTheCarDoctor3 жыл бұрын
Most welcome
@magaan47174 жыл бұрын
Lol😂the the 4x2 on yhe brake pedal is epic. Try this on your next Mercedes-Benz 🙏🔫
@geojor6 жыл бұрын
good work Peter ...
@nigeldunwell814 жыл бұрын
Thank you Mr meerkat
@davidh45388 жыл бұрын
Why don't you loosen that spindle nut while it is on the ground with the tire on, then jack it up.
@PeterFinnTheCarDoctor8 жыл бұрын
Hello and Thanks for feedback. :-)
@TheLokoViejo3 жыл бұрын
Rust makes everything take twice as long to fix and last half as long as it should.
@PeterFinnTheCarDoctor5 ай бұрын
Thanks for comment 👍
@mikkopaavola7596 Жыл бұрын
10vuotta vanha video, mutta olis kyssäri mestarille aiheeseen liittyen. Itellä on vm.99 manuaali e11 1.6 4afe:lla. Onko tietoa noiden vetoakselien yhteen sopivuuksista 1.6-1.3, automaatti-manuaali, vvtkone facelift-prefacelifti? Ite pitäs akseli vaihtaa, mutta motonetti myy pelkkää vetoniveltä joten pitää hakea purkuautosta osa tai tilata ulkomailta eikä 100% tietoa mikä sopii.
@PeterFinnTheCarDoctor Жыл бұрын
Commenting on this video is FREE, but if you have technical questions for me, I charge a small fee for answering them, normally 5 USD $ per question. I am a true Technical Professional, Black Belt in engineering and The Car Doctor! Enjoy and ask. I'll answer professionally. So, if you have question: You pay 5 USD $ via the THANKS button below the video to me. Add user your name to text line. Make the payment and I will then give you a professional answer.
@masthahn6368 Жыл бұрын
I hope that those rusty screws on my car will be as easy to be unscrewed as on your car! 🙏
@PeterFinnTheCarDoctor Жыл бұрын
Thank you for your message. I have read your message. 😀👍
@javziovaldez30245 жыл бұрын
Fuck yeah peter Finn love your videos brother ur making life look easier
@PeterFinnTheCarDoctor5 жыл бұрын
Ok and Thanks !
@jchinckley56658 жыл бұрын
Could you please put your links to your "opposing" side axle replace videos at the top of the screen? Where they are at the bottom, when I go to click them the control bar for the video pops up and won't allow me to click the link! Thanks. :)
@PeterFinnTheCarDoctor8 жыл бұрын
+jchinckley Thanks. Good idea! :-)
@reyntakemori20485 жыл бұрын
We we we we we push dee welcome my friend to America
@PeterFinnTheCarDoctor5 жыл бұрын
Ok
@MrJimbobDP10 жыл бұрын
loosen axle nut wen on ground dude
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks for comment.
@rocaba026 жыл бұрын
Jimbob Randoms that's right
@strongchong110 жыл бұрын
Informative and Entertaining! DOBRA!
@PeterFinnTheCarDoctor10 жыл бұрын
Thanks, Cobra.
@sunnycloud699 жыл бұрын
What size bolt is the big one you took off before the clip n cover ?
@PeterFinnTheCarDoctor9 жыл бұрын
sunnycloud69 This is Toyota's special bolt. Please visit Toyota original dealership shop. Price is about 7 US$.
@melvinisidro5 жыл бұрын
How will i know if its time to change my CV axle? Thanx for the video..
@PeterFinnTheCarDoctor5 жыл бұрын
Good luck my friend. :-)
@manicmandownup5 жыл бұрын
Clicking noise, rapid clicking...while turning your steering wheel. If your CV boots are ripped it’s just a matter of time before you have to replace the axle...
@Marlon_394 жыл бұрын
You forget to show how to replace the trans fluid, fix axel only to destroy trans 😩
@raheelriaz51482 жыл бұрын
Great Man
@PeterFinnTheCarDoctor2 жыл бұрын
Thank You 👍😀
@brams778 жыл бұрын
i am trying to insert my new drive shaft into the gearbox, it has gone in and stoped not all the way. i have tried a hammer, to tap it in, any advice? its a toyota yaris. thanks
@PeterFinnTheCarDoctor8 жыл бұрын
+dave bram Dol you have just similar shaft? Toyota's parts goes normally very easy way.
@bigbootyog4 жыл бұрын
Align the the teeth that goes into the transmission it needs to be perfectly aligned to go in smoothly
@corrierobinson6808 жыл бұрын
so how do u know how tight is tight Enuff if one DOES NOT have a TORQUE WRENCH to tighten up the Bolt aftr getting DRIVE Axle put bk 2gether ????
@PeterFinnTheCarDoctor8 жыл бұрын
+corrie robinson Ok, then use only long bar and your hand force.
@TheWonkax8 жыл бұрын
IF YOU DON'T OWN A TORQUE WRENCH GO BUY ONE. IT IS A NECESSITY FOR THE HOME MECHANIC
@DreamChaser5146 жыл бұрын
What is the torque spec for the ball joint ? In a corolla 2001 ?
@PeterFinnTheCarDoctor6 жыл бұрын
90 NM
@bar20bbq708 жыл бұрын
oh for gods sake man..... stick a screwdriver into the brake caliper to keep it from turning,should have broken nut loose before raising car off ground.
@PeterFinnTheCarDoctor8 жыл бұрын
+BAR 20 BBQ Thanks for comment. :-)
@fueledbytacos2187 жыл бұрын
My car makes a noise when accelarating not turning i think its the drive axle or the bearing it gets louder the faster u go what can it be . Toyota Celica 96 gt com.
@PeterFinnTheCarDoctor7 жыл бұрын
Maybe wheel balancing too
@ezradmello70216 жыл бұрын
wheel bearing
@janzx19 жыл бұрын
Hello! I'd like to ask about gearbox oil that flows out. When i pull the shaft out and the oil starts to flow to a vessel, can i return the same oil to the gearbox afterwards or do i have to add some new oil or is it fine if i dont add anything and it stays at it is?
@PeterFinnTheCarDoctor9 жыл бұрын
Winten R Yes, if oil is clean. So No any sand or trash in oil.
@janzx19 жыл бұрын
Peter Finn Thank you for your answer. Also as i havent opened it yet, how much oil actually flows out? Only some of it or it keeps flowing till empty as its pretty hard to refill the gearbox in my opinion.
@PeterFinnTheCarDoctor9 жыл бұрын
Oil drain out about 1 liter.
@janzx19 жыл бұрын
Peter Finn Thank you again. I managed to change it, but now another problem showed up. My steering wheel is not straight at all when driving. When i dont drive and turn my steering wheel straight, then one wheel seems to be a bit angled as the otherone is straight. Is it possible, that i broke something or should i align it somehow?
@PeterFinnTheCarDoctor9 жыл бұрын
Winten R Hello. You need to adjust your Tie rod end. Look this video: kzfaq.info/get/bejne/gJ2aa6ikma-zmWw.html
@roman0617957 жыл бұрын
will it work the same if the transmission is automatic?
@PeterFinnTheCarDoctor7 жыл бұрын
Yes
@odanne298 жыл бұрын
Very helpful, thanks man..
@PeterFinnTheCarDoctor8 жыл бұрын
Hi and Thanks for Your comment. :-)
@odanne298 жыл бұрын
First time changing a drivaxel, it was not difficult i must say. Your video help alot :)
@juozuks8 жыл бұрын
Thanks Peter!
@PeterFinnTheCarDoctor8 жыл бұрын
You Are Welcome !
@junjun79728 жыл бұрын
Do you need to put transmission fluid after?
@PeterFinnTheCarDoctor8 жыл бұрын
Yes, about 2 liters
@junjun79728 жыл бұрын
+Peter Finn but i heard if you have automatic transmission it wont leak
@anthonyduarte8417 жыл бұрын
9 minutes in and we have our 1st bolt off. lol
@PeterFinnTheCarDoctor7 жыл бұрын
Thanks for comment. :-)
@omarabdelaziz-el-ashry-Eg7 жыл бұрын
but i have Toyota corolla 98 and 30MM bolt is not the right size and 28MM is to samll and i never see 29MM bolt.
@Jamesnov197010 жыл бұрын
The other side is not the same.. Have you done the other side?
@PeterFinnTheCarDoctor10 жыл бұрын
Hi. Thanks for feedback. I need to do new video.
@louiesboys71615 жыл бұрын
great video thanks
@PeterFinnTheCarDoctor5 жыл бұрын
Thanks for comment. 👍
@omarabdelaziz-el-ashry-Eg7 жыл бұрын
are you sure it 30mm this bolt or 29MM bolt ?
@PeterFinnTheCarDoctor7 жыл бұрын
30 mm
@PedroPerez809279 жыл бұрын
Amazing video pete
@PeterFinnTheCarDoctor9 жыл бұрын
pedro perez Thanks.
@octavianconstantinescu29906 жыл бұрын
Hello! How you tup the transmission oil back?
@PeterFinnTheCarDoctor6 жыл бұрын
Yes, but new oil.
@panchovilla434310 жыл бұрын
how i going to refill the oil?
@PeterFinnTheCarDoctor10 жыл бұрын
Gearbox oil fill video link is here: How to change gearbox oil Toyota Corolla. VVTi engine. Years 2000-2010
@JH-wu7co6 жыл бұрын
How much oil is there to refill if only changing the drive shaft?
@AZNowners6 жыл бұрын
all 3l
@genaroaviles85554 жыл бұрын
I WII PUT ANYTHING BETWEEN THE ROTOR TO STOP THE ROTOR
@pupupipi98874 жыл бұрын
All the explaining in pauses make the videos annoying af. Makes no sense