HOW TO REPLACE FRONT WHEEL BEARINGS without Hydraulic Press Toyota Yaris Front Wheel Bearing Change

Рет қаралды 48,653

3 жыл бұрын

How To Replace Front Wheel Bering without Hydraulic Press
Toyota Yaris front Wheel Bering replacement
How to change Wheel Bearing for 2007 Toyota Yaris Base With Basic wheel Bearing Press Tool
#Toyota Yaris front wheel Bearing replacement
Changing front Wheel Bearing on
2007 Toyota Yaris Base With ABS
in this case I had to replace the Steering knuckle with the
Dorman 698-173 Front drive side Steering knuckle for select Select Scion/Toyota Models

Пікірлер: 69

@TrashCanDo 3 жыл бұрын

Your camera work, presentation, and work flow makes everything super easy to follow. Thanks a bunch.

@IshMotorparts 3 жыл бұрын

I'm glad you like it and thank you for visiting Ish MOTORPARTS

@penguinistas 3 жыл бұрын

6:42 great idea to disconnect the shaft without removing the ball joints. well done.

@Thegbiggamerz 2 ай бұрын

Will it hurt the suspension? It didn’t look like it, though I’m no expert. A little unorthodox but seems like it worked!

@gerardlabrecque6175 2 жыл бұрын

Thank you. I think that’s why I need a mechanic. You guys are pretty smart.

@Crystallas 2 жыл бұрын

Excellent backyard job. Thank you for this. Also brush off some of that rust, clean it up since you're already there. It will add years in some cases to the material.

@robbbarnett4978 Жыл бұрын

I would just replace the hub once removed with a brand new one, less work and also there might be undue wear to the hub. The difference in price for the bearing and complete hub isn't that awful much and you don't have to worry about knowing there is wear to the hub. Remember you will also need to get an alignment after this for sure. Thnx for video, it was explicit enough.

@ShopforCFcom 6 ай бұрын

YES! New hub all the way, its only another $40

@philipneri9482 2 жыл бұрын

Hey, that was awesome!…I replaced a wheel bearing on my Echo by taking the hub off the car..and pounding in a new bearing…liked your method better…took me a full day to figure it out!

@IshMotorparts 2 жыл бұрын

Hey Bro,Thank you for watching

@professorlanguagepartners3112 2 жыл бұрын

Great video! You the man!!

@toddcott9510 2 жыл бұрын

From Scotland the home of rusty cars. I have just done this job and the snap ring was as bad as yours. I gas welded a washer to what was left of the snap ring and levered it out. Buying a new hub is unnecessary. I did like the video.

@joelmarquez_wut Жыл бұрын

Thanks for the video!

@einsibongo 2 жыл бұрын

Thanks, well done

@penguinistas 3 жыл бұрын

Thank you for sharing. well done.

@IshMotorparts 3 жыл бұрын

You're welcome and thanks for your visiting ish MOTORPARTS

@nidaldajani728 9 ай бұрын

😊 coffee is tool number one for me too!😊

@kacperoleszek1385 5 ай бұрын

Great film

@harryhenderson2259 3 жыл бұрын

great vid.! thank u friend!:

@freddiejecha8875 3 жыл бұрын

Wow thanks bro

@alyssagutowski6809 3 жыл бұрын

Big job, thank you for sharing. I think I will go to the mechanic on this one. I did the struts and cv axle on our yaris, but this seems too advanced for me.

@IshMotorparts 3 жыл бұрын

Lol, ok Bro thanks for watching

@IshMotorparts 3 жыл бұрын

I meant Sis, lol

@user-rt7pb7qz7i 6 ай бұрын

Nice Job Bro!!!

@jamsheedsidiq4328 8 ай бұрын

Thanks man

@IshMotorparts 8 ай бұрын

You are welcome brother

@chrisdwarz Жыл бұрын

Saving me a bunch of money and time. Thank you my guy. Good tip on the ladies old undies lmao

@IshMotorparts Жыл бұрын

thanks for watching this video

@PabloLopez-ft9op 3 жыл бұрын

Excelente instructivo amigo! Gracias!

@IshMotorparts 3 жыл бұрын

Gracias Amigo

@rosemarydominguez569 2 жыл бұрын

7:06 Girlfriends old underwear 🤣

@user-2uf2kr2c Жыл бұрын

Hello, if you have a heatgun it gets easier. you heat it up and the two parts will expand/shrink differently. Also WD40 helps. Regards

@albowlly 2 жыл бұрын

Rather that cut with a grinder it is made of case hardened steel . Put it in a vice put some pressure on it then hit it with a hammer and it will split. Wear goggles just in case of a splinter flying off.

@BlondieSL Жыл бұрын

So it's been over 2 years since this video. May I ask, that press set that you use to press the bearing back on, is it still in good condition? Is the long bolt and long nut ok and not stripped? I'm just curious, because several reviews are saying that the bolt and nut get totally stripped. But I wonder if those people who report that are perhaps using an impact wrench.

@IshMotorparts Жыл бұрын

3 hours later lol sorry for late reply, Ok Honestly I have been using this tool a lot and I been using impact wrench as well, as of right now the long bolt and Nut it's still in perfect condition, This is a very important question Thanks for watching this video and God bless

@michaelwise6970 Жыл бұрын

I tried doing the job exactly how you did, But I had to turn the wheel and I tried starting the car and it wouldn't start... I had to get it towed out of the water.. 🤔..

@jregamey Жыл бұрын

The brake pad doesn't really cover the entite rotor? My pad fits on the entjre rotor

@dustin1870 6 ай бұрын

I left when mentioned safety

@chivo850 Жыл бұрын

What is the name of the tool that was used to press in the bearing. That looks so convenient. I would like to find one

@IshMotorparts Жыл бұрын

I used the Orion Motor tech 23-piece FWD front wheel bearing adapter Press Tool

@ricaard 3 жыл бұрын

What was the torque when back together?

@IshMotorparts 3 жыл бұрын

I Torqued this one to 160 foot pounds, but as of a old car 155 - 160 foot pounds that's good, thanks for your visit at ish MOTORPARTS

@ricaard 3 жыл бұрын

@@IshMotorparts thank you for answering!

@IshMotorparts 3 жыл бұрын

@@ricaard you're welcome

@AlexRides808 Жыл бұрын

You didn't have to compress the spring?

@IshMotorparts Жыл бұрын

no, no need to compress the spring, thanks for watching

@ivanov568 2 жыл бұрын

So you were not going to remove the knuckle from the tie rods... but @12:17 it looks like you put a new knuckle lol

@IshMotorparts 2 жыл бұрын

You are Exactly right

@jinw8974 9 ай бұрын

@@IshMotorparts Hi, you didn't shown the bearing outer ring was removed using the tool. Was it difficult or unsuccessful? I'm doing this and it is very hard to do it.

@realfixesrealproblemssewel82 3 жыл бұрын

Putting the disc guard plate back on is optional i suppose

@IshMotorparts 3 жыл бұрын

Thank you for your comment because I don't remember taking ONE out or missing anything , thanks Real fix,

@DidiLeeReco 3 жыл бұрын

Lol funny video what are you doing in the water

@IshMotorparts 3 жыл бұрын

I was just cooling down before Work lol

@blueadept4689 3 жыл бұрын

I think you cut too deep, slight cut and hammer, no go, cut more than hammer wheel hub race with chisel. Other than that, thank you for the instruction.

@IshMotorparts 3 жыл бұрын

I thank are you right, but so far its running like new hope its stays running like this for 5 more Years, lol thank you Bro,

@blueadept4689 3 жыл бұрын

@@IshMotorparts Bro, I did mine, and still nipped the wheel hub, lol. No better than yours, I think I spoke too soon, lol. However, they're is a tie rod race puller by OTC that some techs are using, I think I'm going to go that route my next wheel bearing change. I'll provide the description on Amazon for you. If the tie rod race remover doesn't catch, you cut indentations on the base of the race for the teeth to lock on to.. anyways here it is: OTC (7503) Tie Rod/inner bearing race puller Remover. Again, thank you sir.

@IshMotorparts 3 жыл бұрын

@@blueadept4689 you are so funny, lol

@rikkmode 3 жыл бұрын

so in the end just buy the wheel hug with wheel bearing...

@IshMotorparts 3 жыл бұрын

That would be nice if you can find one with the Bearing already in the Hub, if not just use one already in your hand , thanks for watching and come back soon