How To Replace Intake Manifold Chevrolet Cruze [1.8L 1st Gen 2011-2016]

Рет қаралды 15,752

3 жыл бұрын

🔴 In this video I will show you the procedure to change out your intake manifold on your 1st Generation Chevrolet Cruze. If you have a bad intake manifold tuning valve, they you have to change the entire intake manifold since they do not sell that part separately. If you also have a cracked intake manifold then you have to replace the entire unit. I'm replacing the intake with an OEM GM intake that comes with new fuel rail, fuel injectors, purge valve, map sensor and intake manifold tuning valve.
🔩 Parts And Tools List Below !
🔸Basic Socket Set amzn.to/3aUtPwk
🔸Cordless Ratchet amzn.to/3tCIpRI
🔸3/8” Ratchet amzn.to/36YOJJQ
🔸Deep E socket set amzn.to/3eJQWx5
🔸Torx Bit Set amzn.to/2WWGubA
🔸E-Socket Set amzn.to/3qQqtk3
🔸Lisle Master Disconnect Set amzn.to/3fWxcXy
Parts:
🔹GM GENUINE 55570283 Intake Manifold Assembly amzn.to/3cm0XPi

Пікірлер: 61

@pangthepeach 2 жыл бұрын

Thank you so much for this. This video is honestly super helpful.

@dbell9201 2 жыл бұрын

My man! You’re a blessing I needed this video!

@destroyer1025 2 жыл бұрын

Thank you!! I appreciate you making this video. Followed it step by step and everything works great. Thanks!

@OneTrickTech 2 жыл бұрын

You're welcome!

@stephenmuckenfuss5615 Жыл бұрын

@@OneTrickTech Can that nipple on the right side of the intake be replaced by its self? The one that that vacuum hose connects to for the break boost

@josefranciscoesquertalaman3827 3 жыл бұрын

Excelente tutorial recibe mi Poderosísimo *Like !!!* desde Sonora México.

@SteveRobReviews 2 жыл бұрын

Well done bud 👍

@andrewkoob4674 2 жыл бұрын

Thank you!

@pur3mind683 3 жыл бұрын

Awesome video ill attempt to replace my intake tomorrow . I'll let you know how it goes

@OneTrickTech 3 жыл бұрын

good luck!

@pur3mind683 3 жыл бұрын

@@OneTrickTech hey can i damage my car with my intake not working properly the control arm thing disconnected but i found its not moving properly ?

@OneTrickTech 3 жыл бұрын

@@pur3mind683 is that on your old intake? Im guessing you're talking about the intake tuning valve lever being disconnected. That wont damage your car but might throw a check engine light.

@pur3mind683 3 жыл бұрын

@@OneTrickTech yes sir thats it , the valve its not moving though

@OneTrickTech 3 жыл бұрын

@@pur3mind683 so the arm will move under certain conditions. The engine computer is responsible to command it on and off. You can command it on and off by yourself if you have a high end scanner. If the arm is broken on your intake manifold, you could just replace the arm itself. they do sell it separately. here's a pictures. www.amazon.com/Intake-Manifold-55570283-2011-2018-Chevrolet/dp/B088ND7ZR3/ref=sr_1_3?crid=1RG409BXU1HLT&dchild=1&keywords=intake+tuning+valve+lever&qid=1627617251&sprefix=intake+tuning+%2Caps%2C194&sr=8-3

@duaneulman9915 11 ай бұрын

Thank you

@jackgardner2594 8 ай бұрын

Will this video fix the p2070 code

@josefranciscoesquertalaman3827 3 жыл бұрын

👌 excelente.

@chrisvanek4754 Жыл бұрын

Thank you for your video! I did this today. It started but idles rough. Any suggestions on what to look for on what would cause this? Just hoping to keep it running but also realistic that it might be time to let it go.

@OneTrickTech Жыл бұрын

Tough to say. Will need to look at scanner data to see what's wrong. If there's a flashing check engine light because of a misfire, could be ignition coil and spark plugs. You could have a clogged cat converter, bad oxygen sensor. Also make sure you connected all connectors.

@chrisvanek4754 Жыл бұрын

@@OneTrickTech I truly appreciate the reply. Its misfiring. Flashing check engine light right away. All started with a P2076 code. The replaced intake linkage didn’t fix it. Car would run a few days and one day die 4x. I borrowed a OBD2 to test today. Love your videos.

@chrisvanek4754 Жыл бұрын

Well. It started just fine this morning. Go figure. Codes I get now are P0031 and P0037 for both O2 sensors. It still hesitated a little after driving for a bit so maybe those are the causes of that. Your fix looks to have done the job for the P2076 so thank you! and on to the sensors 😳🙂

@OneTrickTech Жыл бұрын

Glad to hear that. I think you can fix the performance issue just by replacing the first o2 sensor that's bad. Second one is only to monitor catalytic converter performance.

@stillboutit 3 жыл бұрын

Can you come up with a video on how to replace the knock sensor?

@OneTrickTech 3 жыл бұрын

I already replaced the knock sensor on this car. If you're looking to replace it on your car, the procedure is very similar to this video but you don't have to remove the fuel rail or the throttle body. Just remove all the bolts holding the intake manifold and it will give you enough space to move it backwards and get to the sensor which in directly below the intake manifold. It's a E14 or E12 bolt holding it then just disconnect the sensor. Hope that helps!

@stephenmuckenfuss5615 Жыл бұрын

Can that nipple for that break boost vacuum line only be replaced?

@OneTrickTech Жыл бұрын

most likely not, its part of the intake manifold assembly

@doncasillas2609 2 жыл бұрын

Where is the PCV non-return valve located? Can it be tested?

@OneTrickTech 2 жыл бұрын

its on the valve cover. It cant be tested because there is no solenoid or anything. Its vacuum controlled

@jorgebarrera2828 8 ай бұрын

Is it supposed to suck air behind the rectangular hole behind the intake, near the pvc.

@OneTrickTech 8 ай бұрын

you mean in the tuning valve?

@jorgebarrera2828 5 ай бұрын

@@OneTrickTechidk the part but it’s behind the intake. There’s an opening. If you check near the intake by the manifold mine is sucking in air idk why

@realcharlebois8719 Жыл бұрын

can a cracked intake or bad tunning valve cause a cold start rattle? or rough idle without causing the engine light to come on?

@OneTrickTech Жыл бұрын

yes especially the rattle, it tends to disappear as the intake manifold warms up

@realcharlebois8719 Жыл бұрын

@@OneTrickTech that's exactly what it does, it used to have a Cam phaser rattle, but theve both been replaced along with the valve cover. Now its a whole different rattle, cold start only and goes completely away when the engine is warm.

@OneTrickTech Жыл бұрын

Hard to call, its a ~600$ part. You will need to isolate the noise to see exactly where is coming from. Try listening with a stethoscope kit like this one (Lisle 52750 Stethoscope Kit). It will help a lot to isolate the noise.

@afiqariff10 Жыл бұрын

will it sound like tapping noise? cause i already adjust my lifter but still have tapping noise at cold start. it almost dissapeared after the engine warm up

@JustaVegasBaby 10 ай бұрын

I forgot to take the fuse out for the fuel will I be good?

@OneTrickTech 10 ай бұрын

get lots of rags ready because the fuel will spray a lot when taking off the fuel line

@JustaVegasBaby 10 ай бұрын

I’m still working on it, is it still too late to remove it? I think I’m just going to continue in the morning

@JustaVegasBaby 10 ай бұрын

Also thank you so much for your response 🙌🏻

@andyuscum Жыл бұрын

the bolt from the bottom..how do you access it ?

@OneTrickTech Жыл бұрын

you have to go underneath the car, with a long extension.

@andyuscum Жыл бұрын

@@OneTrickTech ok thanks gonna tackle this soon

@LyncolnYo 4 ай бұрын

Did you need a empty gas tank for this repair?

@OneTrickTech 4 ай бұрын

@LyncolnYo nope

@AirFriedCPU Жыл бұрын

FUCK I snapped the nipple that the brake booster hose goes onto do I have to replace the whole intake manifold assembly?

@OneTrickTech Жыл бұрын

if you can still put the hose back on then put it on with a worm gear clamp. If no, try to glue the broken piece and put a clamp afterwards.

@AirFriedCPU Жыл бұрын

@@OneTrickTech I have it glued on right now I’m scared to even touch it before I purchase my new manifold because I don’t want it to come apart

@Nk155 2 жыл бұрын

Can a cracked manifold make a knocking noise?

@OneTrickTech 2 жыл бұрын

Not really. A cracked manifold can cause engine performance issues and misfires.

@MasQueAutosRD Жыл бұрын

@@OneTrickTech One more question, can a crack manifold generate code P0442 Small leak detected?

@OneTrickTech Жыл бұрын

@@MasQueAutosRD No. That's an evap related code. You will need to smoke test the evap system to find the leak. There is a purge valve on the intake manifold which can cause that code.

@MasQueAutosRD Жыл бұрын

@@OneTrickTech ok, thanks. I replaced the gas cap and purge valve. Still getting same code and symptoms...

@OneTrickTech Жыл бұрын

@@MasQueAutosRD yea like I said, you will need to smoke test it to isolate the leak. You will probably need to go to a shop for that. If there's no drivability issues then it wont be so urgent to fix.